HOMEFISH Solar TPMS

Contents

HOMEFISH Solar TPMS Tire Pressure Monitoring System

Model: Solar TPMS

1. Introduction

Thank you for purchasing the HOMEFISH Solar TPMS (Tire Pressure Monitoring System). This system is designed to enhance your driving safety by providing real-time monitoring of your vehicle's tire pressure and temperature. Upon installation, the system continuously monitors these parameters. Should any abnormal tire pressure or temperature be detected, the system will alert you with audible warnings and flashing icons, enabling prompt action. This proactive approach helps prevent traffic accidents and ensures driver safety. Furthermore, the TPMS contributes to improved vehicle comfort, reduced tire wear, optimized fuel consumption, and prevention of tire blowouts.

2. Package Contents

Please check the box for the following items:

  • 1x TPMS Display Unit
  • 4x External Tire Pressure Sensors (labeled FR, FL, RL, RR)
  • 4x Anti-theft Nuts
  • 1x Spanner
  • 1x USB Charging Cable
  • 1x User Manual
Contents of the TPMS package including display, sensors, nuts, spanner, and cable.

Figure 2.1: Package Contents

3. Product Overview

3.1. Display Unit Components

Diagram of the TPMS display unit showing solar panel, USB charging port, cooling vent, control buttons, and screen indicators.

Figure 3.1: TPMS Display Unit Components

  • Solar Panel: For solar charging.
  • USB Charging Port: For USB charging.
  • Cooling Vent: Helps dissipate heat.
  • Control Buttons:
    • Left Select Button (<): Used for menu parameter selection.
    • M Button (M): Long press to enter menu settings.
    • Right Select Button (>): Used for single parameter selection.
  • Display Indicators: Shows Battery Power, Tire Pressure, Temperature Unit, Pressure Unit, Vehicle Icon, and individual tire status (FR, FL, RL, RR).

3.2. Display Unit Dimensions

Dimensions of the TPMS display unit: 94.5mm length, 79.5mm width, 26.7mm height.

Figure 3.2: Display Unit Dimensions

4. Setup and Installation

4.1. External Sensor Installation

The external sensors are designed for quick and easy installation.

Three-step diagram for external sensor installation: 1. Screw in nut, 2. Screw sensor onto valve, 3. Tighten nut with spanner.

Figure 4.1: External Sensor Installation Steps

  1. Prepare the Valve: Remove the original valve cap from your tire.
  2. Install Anti-theft Nut (Optional): If you wish to use the anti-theft feature, screw one of the provided anti-theft nuts onto the tire valve stem. Do not tighten it yet.
  3. Attach Sensor: Screw the corresponding sensor (FR for Front Right, FL for Front Left, RL for Rear Left, RR for Rear Right) onto the valve stem until it is hand-tight.
  4. Secure Sensor: If you used the anti-theft nut, slide it up against the sensor and tighten it using the provided spanner. This locks the sensor in place.
Four external tire pressure sensors labeled FR, FL, RL, RR.

Figure 4.2: External Sensors

Four anti-theft nuts and a spanner tool.

Figure 4.3: Anti-theft Nuts and Spanner

4.2. Internal Sensor Installation

If your system includes internal sensors, professional installation is highly recommended as it involves dismounting the tire from the wheel.

4.3. Initial Power-On and Pairing

  1. Position Display Unit: Place the display unit on your dashboard where it can receive direct sunlight for optimal solar charging and clear visibility.
  2. Power On: The unit will automatically power on when it detects vibration (e.g., when you start driving) or when connected to a power source.
  3. Automatic Pairing: Once the sensors are installed and the vehicle begins to move, the sensors will automatically transmit data and pair with the display unit. Tire pressure and temperature readings should appear on the screen within a few minutes of driving.

5. Operating Instructions

5.1. Unit Settings (BAR/PSI, °C/°F)

To change the pressure and temperature units:

  1. Long press the 'M' button to access the settings page.
  2. Press the '<' or '>' button to select the desired unit (e.g., BAR or PSI for pressure, °C or °F for temperature).
  3. Long press the 'M' button again to confirm your selection and exit, or wait for the page to automatically advance to the next setting.

5.2. Alarm Threshold Settings

You can set custom thresholds for high pressure, low pressure, and high temperature alarms:

  1. Long press the 'M' button to access the settings page.
  2. Press the 'M' button repeatedly to navigate through the settings until you reach the desired alarm setting (High Pressure, Low Pressure, or High Temperature).
  3. Use the '<' or '>' button to adjust the alarm value.
  4. Long press the 'M' button to save the setting and exit directly.

5.3. Tire Position Swap

If you rotate your tires, you can update their positions in the system:

  1. Long press the 'M' button to enter the settings page.
  2. Press the 'M' button repeatedly until you find the tire replacement page.
  3. Use the '<' or '>' button to select the tire position you wish to swap.
  4. Long press the 'M' button to save the change and exit directly.

5.4. Sensor Matching/Pairing

If a sensor is lost, damaged, or needs to be re-paired:

  1. Long press the 'M' button and both the '<' and '>' buttons simultaneously for a few seconds to enter the sensor learning page.
  2. Press the 'M' button to select the desired tire position for the new sensor.
  3. Install the new sensor onto the tire valve.
  4. Inflate or deflate the tire slightly to trigger the sensor, allowing it to pair with the display unit.

5.5. Time and Date Setting

To set the time and date on the display unit:

  1. Short press the 'M' button; the hour display will begin to blink.
  2. Use the '<' or '>' buttons to adjust the hour.
  3. Short press the 'M' button again to move to minutes, then date, and year, adjusting each with the '<' or '>' buttons.
  4. Long press the 'M' button to save the settings and exit.

6. Maintenance

6.1. Display Unit Charging

The display unit can be charged in two ways:

  • Solar Charging: Ensure the display unit is placed where it can receive direct sunlight for optimal solar charging.
  • USB Charging: For faster charging or in low-light conditions, connect the provided USB cable to the USB charging port on the side of the unit and a suitable USB power source (e.g., car charger, power bank).
TPMS display unit being charged via USB cable in a car interior.

Figure 6.1: Display Unit USB Charging

6.2. External Sensor Battery Replacement

External sensors have a battery life of approximately 2 years and feature replaceable batteries.

  1. Unscrew the sensor from the tire valve.
  2. Carefully open the sensor casing (refer to the sensor's design for specific opening method, usually by twisting or prying a cap).
  3. Remove the old battery.
  4. Insert a new battery of the same type (e.g., CR1632, check the original battery for exact type) with the correct polarity.
  5. Close the sensor casing and re-install it on the tire valve.

7. Troubleshooting

ProblemPossible CauseSolution
Sensors not pairing / No display readingsSensors not activated, incorrect installation, display unit off/uncharged.Ensure sensors are correctly installed. Drive the vehicle for a short distance to activate sensors. Check display unit power/charge. Perform sensor matching/pairing if needed.
Inaccurate readingsPressure fluctuations due to temperature, sensor malfunction.Verify tire pressure with a reliable gauge. Note that pressure changes with temperature. Ensure sensors are clean.
Display unit not turning onLow battery, auto-sleep mode.Charge via USB or place in direct sunlight. Unit should wake up with vehicle vibration.
Menu button unresponsiveButton stuck or internal fault.Try pressing firmly. If issue persists, contact customer support.

8. Specifications

FeatureSensorDisplay Unit
Working Frequency433.92 MHz433.92 MHz
Working Voltage2.0V - 3.6V3.7V - 5V
Working Current<10 mA<15 mA
Working Temperature-40℃ to 100℃-20℃ to 85℃
Pressure Monitoring Range0 - 8 Bar (0 - 116 PSI)N/A
Temperature Monitoring Range-40℃ to 100℃N/A
Pressure Accuracy±0.1 BarN/A
Temperature Accuracy±3℃N/A
Waterproof RatingIP67N/A
Battery Life (External Sensor)~2 Years (replaceable)N/A

9. User Tips

  • Efficient Solar Charging: The display unit's solar panel is highly efficient and can maintain its charge even in indirect sunlight or when stored in a garage for several days.
  • Automatic Operation: The display unit typically turns on automatically when vehicle motion is detected and enters a sleep mode after a period of inactivity to conserve battery.
  • Normal Pressure Fluctuations: Tire pressure naturally increases with driving and higher ambient temperatures. Small variations in readings are normal and expected.
  • Anti-theft Protection: Utilize the provided anti-theft nuts and spanner to secure the external sensors and deter theft.

10. Warranty and Support

For any issues not covered in this manual, or for warranty claims, please contact your retailer or the manufacturer's customer support for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.