MEKEDE Universal Headunit Android 15 Navigation GPS Intelligent Systems Wireless Carplay AUTO

Contents

MEKEDE Car Multimedia Player User Manual

Intelligent Car Navigation System

Introduction

Thank you for choosing the MEKEDE Car Multimedia System. This manual provides essential information for the safe and effective use of your device. Please read these instructions carefully before operation.

Safety Measures

  • It is forbidden to watch videos or use other visual accessories while driving. Active use of the system during driving is not recommended as it can reduce attention and may result in violation of traffic laws and accidents.
  • The unit is designed for use in cars with a 12V power supply and a negative ground. Do not install the system in a bus or truck with an on-board voltage of 24V, as this may cause damage to the device.
  • Use a special cleaning device to care for the screen.
  • To avoid overheating, do not allow direct exposure to sunlight and do not install near heating systems. Operating temperature is between 0°C and 35°C. If the temperature inside the vehicle is too high, cool the interior before switching on. It is also not recommended to operate the unit at very low temperatures; wait until the interior temperature returns to normal.
  • Only use the fasteners provided (screws, mounting frames, etc.) for installation. The use of other fasteners may result in damage to the system, and this is not covered by the warranty.
  • Installation and connection of the device shall be performed by a qualified specialist or specially trained staff of the service center.
  • Do not reset to factory settings on your own unless in extreme cases, as this will cause loss of your settings, which may result in incorrect operation of the system.
  • Violation of the above items and improper use may cause the system to malfunction. In this case, warranty service will not be performed.

Setup

Package Contents

The package includes the following items:

  • Head Unit
  • Power Cable
  • Panel bracket
  • RCA Cable
  • Reversing Camera
  • GPS Antenna
  • USB Cable
  • 4G Antenna (for K4 Plus models)

Gift Items (may vary by package):

  • Rearview Camera (AHD 720P)
  • Disassembly Tools
  • Microphone (MIC)
Package Contents for MEKEDE Car Multimedia Player

Image: Contents of the product package, including the head unit, various cables, and mounting accessories.

MEKEDE M800S 10-inch Car Navigation Headunit with included gifts

Image: MEKEDE M800S 10-inch Car Navigation Headunit highlighting gifts like a rearview camera and disassembly tools.

Connection Diagram of the Device

Ensure all wires are properly connected to avoid device faults. Refer to the diagrams below for correct wiring.

K2 Plus Back of Main Unit Wiring Diagram

Image: Detailed wiring diagram for the K2 Plus model, showing connections for power, USB, RCA, GPS, and radio.

K4 Plus Back of Main Unit Wiring Diagram

Image: Detailed wiring diagram for the K4 Plus model, showing connections for power, USB, RCA, GPS, 4G antenna, and radio.

Device Connector Pinout Diagram

Refer to the following pinout details for precise connections:

Interface Area Pin Description
A: RCA Audio and Video Input/Output A1 AMP-POW
A2 AGND
A3 AUX-R
A4 RCA-FL
A5 AUX-L
A6 RCA-FR
A7 SIM-DATA
A8 GND
A9 SIM-CS
A10 GND
B: 360° Panoramic Device (5V DC) B1 L-TURN
B2 R-TURN
B3 GND
B4 F_CAM_VID
B5 GND
B6 R_CAM_VID
C: Digital TV, CAN C1 GND
C2 TV12V
C3 TV_L
C4 TV_R
C5 M_NRST
C6 TV-V
C7 MCU-RX(CAN-TX)
C8 MCU-TX(CAN-RX)
D: One USB Interface D1 USB_DPO
D2 USB_5V
D3 USB_DNO
D4 GND
E: Double USB Interface E1 USB_DPI
E2 USB_5V
E3 USB_DNI
E4 GND
E5 USB_DP2
E6 USB_DN2
F: Reverse Video Cable F1 CDC-TX
F2 NC
F3 CDC-RX
F4 GND
F5 IR-OUT
F6 CAM-VIDEO
G: Power Cable Interface G1 GND - 12VDC
G2 B+ +12VDC
G3 ACC Key Switch +12VDC
G4 ILL small lights detecting
G5 BACK Reverse detecting line
G6 KEY2 Steering wheel control study -2
G7 KEY1 Steering wheel control study -1
G8 ANT ANT power +12VDC
G9 FR- Front right speaker (-)
G10 RL- Rear left speaker (-)
G11 FR+ Front right speaker (+)
G12 RL+ Rear left speaker (+)
G13 FL- Front left speaker (-)
G14 RR+ Rear right speaker (+)
G15 FL+ Front left speaker (+)
G16 RR- Rear right speaker (-)

Rear Camera Connection

Without CANBUS Box

Connect the reversing control wire to the reverse light power supply (12V) and the camera power to the car's ground. The yellow video cable connects to the head unit's video input.

With CANBUS Box

If you have a CANBUS box, the yellow line connection for reverse control may not be needed. Ensure the reverse control line (G3 area) is connected to the CANBUS box. Connect the camera power to the car's ground.

CANBUS Box Setup (If applicable)

If your car's original functions (e.g., steering wheel control) are not working, a CANBUS box may be required. Check your CANBUS photo and select the corresponding type in the settings.

Setup Steps for TS7, T3L, TS18, TS10, M100, M150, Y1, Y2, TS100, TS150, TS200 models:

  1. Connect the CANBUS box as shown in the picture.
  2. Navigate to Settings > Car Settings > Factory (Password: 8888).
  3. Select the appropriate CANBUS type for your vehicle.
CANBUS Box connection diagram

Image: Diagram showing how to connect the CANBUS box to the head unit.

Operating Instructions

Front Panel Control

The front panel features physical buttons for essential functions:

  • MIC: Microphone
  • RST: Emergency reassembly of equipment (Reset)
  • Power Button: Input/output switch, live switch, sound switch
  • Home Button: Return to main menu
  • Back Button: Switching back to the previous menu
  • Volume Up (+): Increase volume
  • Volume Down (-): Lower the volume
Front panel controls of the MEKEDE Car Multimedia Player

Image: Front view of the head unit showing physical buttons and their functions.

Switching the Appliance On/Off

After switching off the ignition and starting the engine, the multimedia system is automatically switched on. The display shows the initial screen. The unit activates automatically after the engine is switched off.

Touch Screen Operation

The unit is equipped with an interactive touchscreen display. Before using it for the first time, the sealed plastic membrane must be removed. Otherwise, the touch screen may not function properly.

  • Touch: Click the necessary item with your finger to start the plugin (signal source) or select the menu item (option).
  • Double Tap: A quick double touch allows you to resize when viewing images.
  • Touch & Hold: Click and hold the item for 2 seconds to trigger an additional action available for that item.
  • Dragging: Touch and hold the selected item, then drag it onto the screen.
  • Moving: Rotate the screen with your finger and keep your finger touched, move your finger in the right direction throughout the screen.
  • Scroll through: Move your finger on the screen in the direction you need to and let go. Rotation can be stopped by touching the screen, or wait until the motion stops itself.

Attention: Do not use metal or sharply sealed objects to control the interactive display. Also, do not apply excessive force when touching the screen.

Main Menu Interface Settings

You can customize the position of icons and freely edit applications on the quick menu bar. You can also set a picture or photo as the background for the main screen.

Customizable widgets and home screen layout

Image: Examples of customizable widgets and home screen layouts on the multimedia player.

UI Display Collection for K2 Plus and K4 Plus

Image: Various theme interfaces available for K2 Plus and K4 Plus models.

FM/AM Radio

To access the Radio, tap the 'Radio' icon on the main menu. The system supports automatic and manual search. You can drag station icons to replace them in the channel list.

FM RDS Radio interface

Image: The FM RDS Radio interface showing station presets and frequency tuner.

DSP Processor / Equalizer

The built-in DSP chip allows for advanced sound settings. Tap the 'DSP' or 'Equalizer' icon to access these features.

  • Equalizer Mode: Adjust sound frequencies using a 32-band equalizer. Presets like Rock, Soft, Jazz, Pop, Classical, and Hall are available.
  • Automatic Volume Mode: Choose recommended settings for listener position (Driver Mode, Passenger Mode, Rear, Center) or manually adjust on the car diagram.
  • Balance Mode: Adjust the volume ratio of speakers for optimal sound.
DSP Equalizer interface

Image: The DSP Equalizer interface with adjustable frequency bands and sound settings.

Music / Video Playback

Connect a USB storage device or insert an SD memory card. Tap 'Music' for audio playback or 'Video' for video playback. The system supports MP4, AVI, WMV, MOV, MKV, MPEG, RMVB, and other formats.

1080P Video playback on the head unit

Image: The head unit displaying 1080P video playback.

Attention: For safety, video playback is restricted while the car is in motion. To view videos, stop in a safe place and apply the handbrake.

Bluetooth (BT) Function

The built-in smart BT system supports mobile phone pairing, hands-free dialing, and music streaming.

Connection Steps:

  1. Tap the 'Bluetooth' icon on the main menu.
  2. On your phone, search for new Bluetooth devices.
  3. Select 'CAR KIT' from the list of available devices.
  4. Enter the PIN (default: 0000) on your phone to confirm pairing.
  5. The system screen will show 'connected' upon successful pairing.
Bluetooth function interface

Image: The Bluetooth interface showing dialing and music playback options.

Wireless CarPlay / Android Auto

The head unit supports wireless CarPlay (for iOS) and Android Auto (for Android) for seamless smartphone integration.

Wireless CarPlay (iOS system) Connection Steps:

  1. Connect your iPhone to the head unit via Bluetooth.
  2. Tap on the 'CarPlay' icon and wait for connection.

Wireless Android Auto (Android system) Connection Steps:

  1. Connect your Android phone to the head unit via Bluetooth.
  2. Tap on the 'Android Auto' icon and wait for connection.
Wireless CarPlay and Android Auto connection steps

Image: Visual guide for connecting to Wireless CarPlay (iOS) and Wireless Android Auto (Android).

Split Screen

On the screen of the main device, you can display two additional devices, for example, the navigation program and music.

MAP Navigation

The built-in global positioning system provides omni-directional map display, synchronous real-time traffic conditions, and accurate positioning. The system supports various navigation software.

GPS Navigation interface with various map applications

Image: The GPS Navigation interface showing various supported map applications like iGO, Sygic, Yandex, Google, Waze, and AMAP.

4G LTE Connectivity

The built-in 4G modules provide high-speed internet and stable signal, allowing you to watch live video, listen to music online, play games, and more.

4G LTE and WiFi module diagram

Image: Diagram illustrating the 4G LTE and WiFi module. Note: 4G Version includes an external SIM card cable.

Language Settings

To change the system language:

  1. Go to Settings > Person > Languages & input.
  2. Select your preferred language from the list.
  3. Confirm the change.

Lantern Settings (RGB)

The device features multicolor illumination. You can set different light modes or choose an automatic color change.

Additional Features (Requires additional accessories)

  • DAB+: For improved sound quality and stronger signal in EU countries.
  • OBDII: Monitor real-time data and fault codes from the on-board computer.
  • TPMS: Automatically monitor tire pressure and temperature.
  • AV Output: Output displayed content to rear headrest screens.
  • ADAS DVR: Driving recorder with collision warning, lane departure warning.
  • AHD HD Reversing: Clearer rear view video quality.
  • 360° Camera: Requires a built-in 360 Camera Chip on the motherboard. To activate, go to Settings > Factory (Password: 3368) > Switch Backup Camera > Inner 360.

Maintenance

Cooling Fan Operation

To start the cooling fan:

  1. Go to Settings > Device > More settings.
  2. Locate the cooling fan settings and activate it.

The cooling fan helps maintain optimal operating temperature for the device.

General Cleaning

Use a soft, lint-free cloth specifically designed for electronic screens. Do not use harsh chemicals or abrasive materials.

Troubleshooting

If you encounter any issues, try disconnecting and then reconnecting your device. You can also use the 'Reset' button (RST) on the front panel for a soft reset. If the problem persists, refer to the table below or consult an authorized dealer.

Possible Malfunctions and Solutions

Symptom Probable Cause Solution
General Problems
Device doesn't turn on. Ignition key not in 'On' position. Turn the key to the 'On' position.
Overheated fuses (15A). Blown fuse. Check the circuit breaker in the device; if not working, replace with a good one of the same nominal size.
Incorrect connection of electrical supply wires (black and yellow). Wiring error. Check the connection of the electrical supply.
Bluetooth (BT)
Phonebook contacts are not transferred. No rights on the phone. After connecting the phone to the device, go to the BT setting on the phone and authorize the transfer of the phone book.

Specifications

Attribute Value
Mounting Size 9"/10"
Screen Resolution 1280x720 IPS
Screen Size 9" and 10"
CPU 8-core
RAM DDR3 2GB/3GB/4GB/6GB/8GB
ROM 32GB/64GB/128GB/256GB
Operating System Android 12 (Real Android 15 for K4 Plus)
Maximum Output Power 4 x 45 W
Sound Amplifier TDA 7388/Toshiba 001 (M200S M300S), TDA7851/7850/7838 (M400S M500S M600S M700S M800S)
Chip FM Tuner NXP TEF6686
Features of the Equalizer Low Pass Filter, Tone Compensation, Balance Mode, Surround Sound Mode, Extended Equalizer settings (32 bands)
Car-Play / Android Auto Supported (add-on Car Link)
Video Format RMVB, MKV, MOV, WMV, AVI, MPG, TS, H.264 codec and others.
Audio Format MP3, WMA, WAV, OGG, FLAC
GPS Built-in receiver with external antenna
Software for Navigation Support
Wi-Fi Support
360° Camera Support
BT A2DP and BT address book transfer
Control of Steering Wheel Buttons Support
ADAS DVR Activation in the settings menu
AHD HD Reversing Automatic activation of video input
4G Internet / 4G LTE Support
DSP Support
Start 16 c~ 20 c
Voltage During Operation DC12V
Voltage at Operating Range 9V~16V
Electric Current 15A
Operating Temperature -20°C - +70°C
Main Menu Language Support for multiple national languages

Warranty & Support

The product comes with a 3-year warranty from the date of purchase. We are committed to providing continuous support and updates for your car multimedia player.

  • Free firmware, software, user interface, and GPS navigation map updates are provided.
  • All products undergo strict quality inspection before shipment.
  • If the product has problems within 15 days after receipt confirmation, free replacement is supported (contact staff for details).

For further assistance, please refer to the User Manual (PDF) for additional details.

User Tips

  • CANBUS Compatibility: If your vehicle has specific features like a JBL amplifier, subwoofer, steering wheel controls, joystick, or climate control panel, ensure you have the correct CANBUS adapter (e.g., 'Raise' type) and that it is properly configured in the system settings.
  • Powered USB Hub: For connecting multiple USB accessories (like a DVR or additional storage), consider using a 4-port USB HUB with an active power supply (e.g., converting 12V to 5V at 5A load) to ensure stable operation.
  • GPS Antenna Adapters: If using standard GPS antennas, you may need Fakra adapters for proper connection to the radio.
  • Check Mounting Brackets: Verify that your package includes the necessary mounting brackets for installation. Universal mounts are often included but can sometimes be missing.
  • Verify All Cables: Before starting installation, ensure all necessary power and connection cables are present in the package.

© 2024 MEKEDE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.