UGREEN ES702

Contents

UGREEN Jump Starter Power Pack ES702 User Manual

Model: ES702

1. Introduction

Thank you for choosing the UGREEN Jump Starter Power Pack ES702. This device is designed to provide a powerful and reliable solution for jump-starting vehicles with dead batteries, while also serving as a portable power bank and emergency light. Please read this manual thoroughly before use to ensure safe and optimal operation.

UGREEN Jump Starter Power Pack ES702 with clamps and storage pouch
Figure 1: UGREEN Jump Starter Power Pack ES702 and accessories.

2. Safety Information

This jump starter is equipped with multiple safety features to protect both the device and the user. Always follow these guidelines:

  • Ensure the product power is greater than 60% before attempting to jump start a vehicle.
  • Do not connect the positive and negative clamps together.
  • Avoid exposing the device to extreme temperatures outside its operating range (-4℉ to 140℉).
  • Keep out of reach of children.
  • Do not disassemble or modify the device.
Diagram showing 3C Certification and Dual Battery Protection functions
Figure 2: Built-in safety protections including low battery, reverse connection, reverse charging, overcurrent, short circuit, high temperature, overvoltage, and undervoltage protection.

3. Package Contents

Please check the package for the following items:

  • UGREEN Jump Starter Power Pack ES702
  • Smart Jump Leads (Battery Clamps)
  • USB-A to USB-C Charging Cable
  • Storage Bag
  • User Manual

4. Product Overview

The UGREEN ES702 features a robust design with a digital display and versatile ports.

  • Digital Display: Shows the current battery charge status.
  • USB-A and USB-C Ports: For charging external devices.
  • Emergency Light: Integrated LED flashlight with multiple modes.
Close-up of the digital display showing '100%' battery level
Figure 3: Digital display indicating battery level.
UGREEN Jump Starter charging a phone and tablet via USB-A and USB-C ports
Figure 4: USB-A and USB-C ports for charging other devices.

5. Specifications

FeatureDetail
BrandUGREEN
Model No.ES702
Battery Capacity12000mAh
Battery TypeLi-Polymer Battery
Input5V/2.4A (USB)
Output5V/2.4A (USB)
Total Output24W Max
Starting Current600A
Peak Current1000A
Vehicle Service Type12V/6.0L Gasoline, 12V/3.5L Diesel Engines
Operating Temperature-4℉ to 140℉ (-20℃ to 60℃)
Dimensions161.5mm x 85mm x 33mm
Net Weight470g
ProtectionOver-discharging, Short Circuit Protection, Reverse Connection, Reverse Charging, High Temperature, Overcurrent, Overvoltage, Undervoltage, Low Battery
CertificationCE
Product parameters table and dimensions of the UGREEN ES702 jump starter
Figure 5: Detailed product parameters and dimensions.

6. Setup

Before first use, fully charge the UGREEN Jump Starter. The digital display will show the battery level. Ensure the device has at least 60% charge before attempting to jump start a vehicle.

  1. Connect the provided USB-A to USB-C cable to the jump starter's input port.
  2. Connect the other end of the cable to a suitable USB power adapter (not included).
  3. The digital display will show the charging progress. Once 100% is displayed, the device is fully charged.

7. Operating Instructions

7.1. Jump Starting a Vehicle

Follow these three simple steps to jump start your vehicle:

Three simple steps for jump starting a car: Connect, Clamping, Ignition
Figure 6: Visual guide for jump starting a vehicle.
  1. Connect: Connect the smart ignition wire (jump leads) to the jump starter. Start the power supply and turn on the product.
    Note: Before use, make sure the product power is greater than 60%.
  2. Clamping: Open the car hood and correctly connect the positive (red) clamp to the positive (+) terminal of the car battery and the negative (black) clamp to the negative (-) terminal of the car battery.
  3. Ignition: If the green light on the smart ignition wire is always on, you can start the car. After the car starts, immediately remove the ignition clip from the car battery, then disconnect it from the jump starter.

7.2. Using as a Power Bank

The UGREEN Jump Starter can charge your electronic devices:

  1. Connect your device's charging cable to either the USB-A or USB-C output port on the jump starter.
  2. The jump starter will automatically begin charging your device.

7.3. Using the Emergency Light

The built-in LED flashlight offers three modes for various situations:

Emergency light modes: Normal Lighting, Alert Mode, SOS mode
Figure 7: Emergency light functions for safety.
  1. Normal Lighting: Press and hold the power button for three seconds to turn on the normal light.
  2. Alert Mode: Press the power button once after starting the normal light to switch to alert mode (flashing).
  3. SOS Mode: Press the power button twice after starting the normal light to switch to SOS mode (Morse code signal).

8. Maintenance

  • Store the jump starter in a cool, dry place away from direct sunlight and moisture.
  • Recharge the device every 3-6 months if not in regular use to maintain battery health.
  • Clean the exterior with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Ensure the ports are free from dust and debris.

9. Troubleshooting

Device does not turn on:
Ensure the device is charged. If the battery is completely depleted, it may take a few minutes of charging before the display activates.
Vehicle does not start after jump-starting:
Check that the jump leads are securely connected to the correct battery terminals. Ensure the jump starter has sufficient charge (above 60%). If the vehicle still doesn't start, the car battery may be severely damaged or there might be another issue with the vehicle.
Digital display is not working:
Try charging the device. If the issue persists, contact customer support.
Device is getting hot during use:
Some heat is normal during operation, especially during jump-starting or heavy charging. If the device becomes excessively hot or emits smoke/odor, discontinue use immediately and contact customer support.

10. User Tips

  • Always ensure the jump starter is charged above 60% before heading out, especially on long trips.
  • Keep the jump leads clean and free of corrosion for optimal performance.
  • If you need a replacement cable, check with UGREEN customer support for compatible accessories.

11. Warranty and Support

The UGREEN Jump Starter Power Pack ES702 comes with a 12-month warranty from the date of purchase. This warranty covers manufacturing defects but excludes damage caused by human factors, improper operation, or products that cannot be resold.

If you encounter any issues or have questions, please contact UGREEN customer support. We aim to respond within 24 hours and take action within 48 hours.

Warranty Exclusions:

  • Damage caused by human factors.
  • Damage due to improper operation.
  • Products that cannot be resold.

Please check the quality of products before using and inform us if any defects are found. We will replace defective products within the guarantee period, excluding the factors mentioned above.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.