ETENWOLF S1

Contents

ETENWOLF S1 Portable Air Compressor User Manual

Model: S1

Introduction

The ETENWOLF S1 Portable Air Compressor is a compact, lithium-powered inflator designed for a variety of inflation needs, including passenger cars, SUVs, motorcycles, bicycles, and sports balls. Featuring a high-capacity 5200mAh battery, it delivers efficient inflation up to 160 PSI with a 100% duty cycle. This manual provides essential information for safe and effective use of your device.

For a downloadable PDF version of this manual, please refer to the official user manual PDF.

Package Contents

Ensure all items are present in the package:

  • 1 x ETENWOLF S1 Tire Pump
  • 1 x Air Chuck
  • 1 x A to C Charging Cable
  • 1 x T-shaped quick connector
  • 1 x French copper adapter
  • 1 x Ball needle
  • 1 x Storage Bag
  • 1 x User Manual
Contents of the ETENWOLF S1 package including the air compressor, various nozzles, charging cable, and storage bag.
Image: What's in the box - ETENWOLF S1 Portable Air Compressor and accessories.

Product Overview

Familiarize yourself with the components and display of your ETENWOLF S1 air compressor:

Diagram of the ETENWOLF S1 Portable Air Compressor with numbered parts and their functions.
Image: Product Overview - Numbered diagram of the air compressor's buttons, display, and ports.
  1. '+' Pressure Increase Button
  2. '-' Pressure Decrease Button
  3. Start/Pause Power Button
  4. Light Button
  5. Mode Button (for switching units)
  6. Manual Mode Indicator
  7. Car Mode Indicator
  8. Bicycle Mode Indicator
  9. Ball Mode Indicator
  10. Pressure Unit Display
  11. Target Value Display
  12. Actual Pressure Value Display
  13. Progress Bar
  14. Battery Level Indicator
  15. Safety Warning Icon
  16. High-Pressure Hose
  17. Type-C Port
  18. LED Light

Setup

Quick Start Guide

  1. Power On: Press the power button Power button icon for 0.5 seconds to turn on the device.
  2. Retrieve Hose: Take out the high-pressure hose (16) from the back of the unit.
  3. Connect: Screw the hose nozzle clockwise into the object to be inflated.
  4. Select Mode: Short press the mode button Mode button icon to switch between the four preset modes: Manual Mode, Car Mode, Bicycle Mode, and Ball Mode.
  5. Set Pressure Unit: Long press the mode button Mode button icon to switch the pressure unit between PSI, KPA, and Bar.
  6. Adjust Target Value: Press the '+' button to increase the target pressure value, or the '-' button to decrease it.
  7. Start Inflation: Press the power button Power button icon again to start inflating.
  8. Auto Stop: The pump will automatically stop once the preset pressure value is reached.
Four-step visual guide for using the ETENWOLF S1 air compressor: Connect & Power On, Set Mode & Unit, Start Inflating, Auto Stop.
Image: Quick Start Guide - Visual steps for inflation.

Operating Instructions

Button Operation Guide

  • Mode Button: Short press to cycle through Manual, Car, Bicycle, and Ball modes. Long press to switch between PSI, KPA, and Bar pressure units.
  • Start/Pause Power Button: Long press for 0.5 seconds to turn on, long press for 2 seconds to turn off. Short press to start or pause inflation.
  • Light Button: Short press to cycle through three lighting modes: High Beam, Slow-Speed Strobe Light, and SOS Light.

Preset Pressure Values

The display shows the target value (smaller numbers) and the actual pressure value (larger numbers). The following preset ranges are available:

Mode Adjustable Pressure Range
Manual Mode 3.0 - 160.0 PSI
Car Mode 8.0 - 130.0 PSI
Bicycle Mode 10.0 - 145.0 PSI
Ball Mode 3.0 - 16.0 PSI
Diagram showing four inflation modes: Bicycle, Ball, Car, and Custom, with default PSI values and approximate inflation times.
Image: 4 Inflation Modes - Default PSI and approximate inflation times for various items.

Memory Pressure Setting

The inflator remembers your last set target pressure value and unit. This allows you to change the default pressure at any time without re-entering it.

LED Light Functionality

The LED light is located at the top of the inflator. Short press the light button to turn it on and cycle through High Brightness, Flashing Mode, and SOS Signal.

Note: After one hour of continuous operation, the light will flash as a reminder. Press the light button to cancel the auto shut-off. If no operation is performed, it will flash and then turn off.

Image showing the ETENWOLF S1 with its LED light illuminating an engine bay, demonstrating Illumination Light, Slow-Speed Strobe Light, and SOS Light modes.
Image: LED Strong Lighting - Demonstrating illumination, strobe, and SOS light modes.

Battery Charging and Indicator

The battery level indicator (14) is divided into four bars, each representing 25% of the total capacity. The indicator will flash when the battery level drops below 10%.

For optimal charging, use a certified PD charger and the provided charging cable. A full charge from 0% to 100% typically takes 2-3 hours. Fully charge the inflator before its first use.

Remark: The inflator will automatically shut off if inactive for 5 minutes after being fully charged. The inflator cannot be used while charging.

Pressure Calibration

Altitude variations can cause a pressure reading difference of 1-3 PSI. In high-altitude areas (above 5000 ft / 1524 m), you may need to recalibrate the pump's pressure sensor.

Calibration Steps:

  1. Press the power button to turn on the device.
  2. Press and hold the light button Light button icon and the mode button Mode button icon simultaneously for 10 seconds.
  3. The screen will restart, indicating successful recalibration.

Notes on Calibration:

  • Turn on the device before starting calibration.
  • The high-pressure hose must not be connected to anything during calibration. Any applied pressure will invalidate the process.
  • Battery power or another power source is required for calibration.
  • The device does not store new calibration settings. It will reset to sea-level calibration (0 ft/m) when powered off.
  • In high-altitude areas, manual calibration is required each time the pump is turned on.

Maintenance

  • Storage: Store the product between -4°F~140°F (-20°C~60°C). Extreme temperatures can damage the battery and shorten its lifespan.
  • Battery Care: Charge the inflator at least once every three months to maintain good performance and prevent reduced battery efficiency from long-term storage.
  • Cleaning: Use this product in a dry and clean environment. Dust and sand intrusion may damage the product. Do not clean the product with water.
  • General Handling: Keep the product away from heat sources and do not leave it inside a hot car for long periods, as overheating can increase the risk of fire or explosion.
Diagram showing various protection systems: Motor Protection, Low-Temp Charging Protection, High-Temp Charging Protection, Low-Temp Discharge Protection, High-Temp Discharge Protection, Overvoltage Protection, Cell Protection, High-Voltage Protection.
Image: Multi-Shield Protection System - Built-in safety features.

Troubleshooting

Problem Solution
Inflation speed is slow. Check if the inflation hose is damaged and ensure the battery is sufficiently charged.
Pump turns on but does not inflate. Check if the pressure of the object exceeds the preset pressure.
Battery indicator does not appear on the screen after charging. Use a certified PD charger and cable, then try charging again.
Pump stops working due to extreme temperature conditions. Ensure the pump operates within 0°C / 32°F ~ 45°C / 113°F (charging) or -20°C / -4°F ~ 74°C / 165°F (inflating/deflating).
Safety warning icon lights up (abnormal pressure or motor response). Turn off the machine, wait 10 minutes, then restart.
Pump is inflating but the display shows zero pressure. If the air pressure is below 3 PSI, the display will show zero due to the pump's minimum detection range.
Battery level indicator differs during inflation compared to standby. This is normal due to lithium battery voltage drop during discharge.
Safety warning icon shows E08. If the issue persists after turning off and restarting, send the device for repair.
Display E10 Error Code (Motor fault). Motor fault warning, motor stops. Should recover after 30s. If persists, send for repair.
Display E11 Error Code (Low-temp charging). Restore temperature to above 0°C.
Display E12 Error Code (High-temp charging). Restore temperature to below 45°C.
Display E13 Error Code (Low-temp discharge). Restore temperature to above -20°C.
Display E14 Error Code (High-temp discharge). Restore temperature to below 58°C.
Display E15 Error Code (Working time exceeded). Warning icon flashes for 30s. Check object for leaks.
Display E16 Error Code (Overpressure protection). Normal operation resumes after pressure release.
Display E17 Error Code (High-pressure operation exceeded working time). Warning icon flashes for 30s. Check if inflated component is functioning abnormally.
Display E18 Error Code (Battery damage). Battery damage warning icon and battery indicator light. Device shuts down after 30s. Send to factory.
Display E22 Error Code (Preset value lower than actual). Preset value is lower than the actual air pressure value.

Specifications

Attribute Value
Name Portable Tire Inflator
Model S1
Dimensions 169.2 x 53.4 x 67 mm
Inflation Pressure Range 3.0-160.0 PSI / 0.20-11.00 bar
Operating Temperature Charging: 32°F–113°F (0°C-45°C), Discharging: -4°F~165°F (-20°C~74°C)
Storage Temperature -4°F~140°F (-20°C~60°C)
High-Pressure Hose Length 355 mm
Battery Capacity 5200 mAh (19.2 Wh)
Operating Noise Below 85 dB within 1 meter
Input Type-C: 5V 2A
Working Time Approximately 20 minutes at 25°C ambient temperature, within 20–50 PSI inflation pressure range
Charging Time 2-3 hours
Sensor Accuracy ±1 PSI

User Tips

  • Pre-set Pressure: Always pre-set your desired pressure before starting inflation to avoid over-inflation and ensure safety.
  • Check Connections: Ensure the hose is securely screwed onto the valve stem to prevent air leakage and ensure accurate readings.
  • Monitor Progress: While the device has an auto-stop feature, it's good practice to monitor the inflation process, especially for sensitive items like bicycle tires or balls.
  • Regular Charging: Charge the device regularly, even if not in frequent use, to maintain battery health and ensure it's ready when needed.
  • Use Correct Adapters: Always use the appropriate nozzle adapter for the item you are inflating to ensure efficient and safe operation.

Frequently Asked Questions (FAQ)

Q: Can I use the inflator while it's charging?
A: No, the ETENWOLF S1 Portable Air Compressor cannot be used while it is charging.
Q: How long does it take to inflate a standard car tire?
A: For a 195/65/R15 car tire, it takes approximately 120 seconds to refill from 28 PSI to 35 PSI. Full inflation from flat can take around 8 minutes.
Q: What should I do if the display shows 'E15'?
A: Error code E15 indicates that the pump has exceeded its working time. The warning icon will flash for 30 seconds before returning to normal. Check the object being inflated for any leaks.
Q: Is the device noisy during operation?
A: The operating noise level is below 85 dB within 1 meter, designed for a quiet run.

Warranty and Support

The ETENWOLF S1 Portable Air Compressor comes with a two-year warranty from the date of purchase. During this period, we will repair or replace any defective product caused by manufacturing faults.

Contact Information:

Manufacturer: Guangdong Bestek Technology Co., Ltd

Brand Owner: Mozhen Technology (Shenzhen) Co., LTD

Please register your product at https://etenwolf.com to receive a 1-year extended warranty.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.