Important Safety Information and Warnings
Please read all instructions carefully before installation and operation. Pay special attention to warnings indicated by the symbol !.
- This unit is designed for a 12V vehicle power supply system with a required grounding wire. Do not install in 24V vehicles, as this will cause damage.
- Do not repair the power fuse without professional guidance. Improper fuse use can damage the unit or cause fire.
- To avoid traffic violations and accidents, drivers must not watch videos or operate the unit while driving.
- For safety and proper product function, professional installation, disassembly, or repair is recommended.
- Avoid placing this product in humid environments or near water to prevent electric shock, fire, or other damage.
- Note: To prevent damage, do not energize the unit until all power cords are correctly connected. This product contains small parts; keep out of reach of children.
Setup
Pre-Installation Test
Before full installation, perform a quick test to ensure the unit is functioning correctly:
- Combine the red and yellow wires of the car stereo and connect them to the positive pole of a 12V battery.
- Connect the black wire to the negative pole of the battery.
- After 2 seconds, check if the car stereo screen lights up. If it does, the unit is functioning properly.
Installation Methods
There are three common ways to install the unit. Choose the method that best suits your vehicle's dashboard configuration. You may also re-install the new radio using the method of your original car radio.

- Screw-fixed installation: Secure the unit using screws.
- Card position fixed installation: Install the unit into a designated slot.
- Special frame fixed installation: Use a specific mounting frame for integration.
Wiring Instructions
Proper wiring is crucial for the unit's functionality and safety. Refer to the diagrams below for connections.
Note: Always connect the rear view wire, even if a rear view camera is not used, to ensure optimal WiFi and Bluetooth signal performance.
1. Main Harness Connection

2. Back Interface Diagram
Identify the various input and output ports on the rear of the unit.

- Power Cable: Main power input.
- RCA Input/Output: For audio/video connections.
- CANBUS Serial Cable: For vehicle data communication (if applicable).
- 2 USB Cables: For USB devices.
- Camera Input: For front or rear camera.
- Radio Antenna: For FM/AM reception.
- GPS Antenna: For navigation functionality.
3. Rear View Camera Wiring (Optional)
If installing a rear view camera, follow this wiring diagram:

- Reversing Trigger Line: Connect this wire to the reversing line in the power harness (e.g., Back A6).
- Red Wire (Camera Power): Connect to the positive pole of the reverse light cable.
- Camera Power Cable: Connect to the camera's power source.
- Monitor: Ensure your monitor supports NTSC format or PAL/NTSC auto switch.
Operating Instructions
1. Machine-Host Controls
| Symbol | Operation & Control |
|---|---|
| MIC | Built-in microphone hole |
| RST | Reset (press with a sharp object) |
| ⏻ | Power on/off (press and hold for 3s to power off). Short press repeatedly to mute/unmute. |
| ⌂ | Go to main menu |
| ↩ | Return to the previous interface |
| ⊞+ | Press or hold repeatedly to increase volume |
| ⊞- | Press or hold repeatedly to decrease volume |
2. On-Screen Main Interface Icons
| Icon | Name | Operation |
|---|---|---|
| ⌂ | Main menu | Touch to switch screen to main menu |
| ∧ | Hide shortcut menu | Touch to hide the shortcut menu button area |
| □ | Backstage | Touch to show all programs running in the background |
| ↩ | Return | Touch to switch screens to return to previous screen |
| ⚙️ | Setting | Touch to enter settings |
| ⊞ | Application | Touch to enter more app interface |
| ⛯ | Navigation | Touch to enter navigation |
3. On-Screen Drop-Down List Icons
| Icon | Name | Operation |
|---|---|---|
| 📶 | Wi-Fi | Turn on/off Wi-Fi |
| Ⓑ | Bluetooth | Turn on/off Bluetooth |
| ⚫ | Screen off | Open/Close Screen |
| 📸 | Screenshot | Touch to take a screenshot |
| 🚗 | Car setting | Touch to enter Car setting |
| 🧹 | Clean-up | Touch to clean |
| 📺 | Video out | Touch to set Video out |
| Ⓞ | OPTICAL | Turn on/off OPTICAL |
4. On-Screen APP Icons
| Icon | Name | Operation |
|---|---|---|
| Ⓑ | BT | Touch into Bluetooth |
| 🗣️ | ESSGOO Voice | Touch to enter smart voice settings |
| ➕ | ESSGOO + | Touch to enter the intelligent voice software |
| 📻 | DAB+ | Touch to enter DAB+ |
| 🗺️ | HERE WeGo | Touch to enter offline map |
| ⚙️ | Car set | Touch to enter car settings |
| ⚙️ | Car Settings | Touch to enter settings, enter password 000000 for factory settings |
| 📍 | Maps | Touch to enter Google Maps online |
| 📱 | Phonelink/TIMA | Touch to connect to mobile phone |
| ▶️ | Video | Touch to enter video playback |
| 📁 | Filemanager | Touch to enter file management |
5. Main Interface Quick Bar
- Long press an icon to delete it from the shortcut bar.
- Click the '+' sign to add a shortcut.
- Up to 5 shortcut icons can be displayed. Swipe left/right to switch if more than 5 icons are present.
6. Radio Operation
Access the radio function from the main menu. Icons allow for band switching, mute, station navigation (previous/next, search), near/far tuning, audio effects (DSP), RDS, fine tuning, and station list management.
7. Bluetooth Functions
The Bluetooth interface allows for dialing, accessing contacts, viewing call history, managing paired devices, and adjusting Bluetooth settings (auto-answer, auto-connect, network sharing). You can also play music via Bluetooth.
8. CarPlay and Android Auto
This unit supports both wired and wireless CarPlay and Android Auto for seamless smartphone integration.

Connection Methods:
- Wireless: Turn on Wi-Fi and Bluetooth on your phone. Go to phone settings > General > CarPlay/Android Auto, select 'Essgoo-BT', pair, and connect.
- Wired: Connect your phone to the unit's USB port using a data cable (original phone cable recommended for stability). Follow on-screen prompts.
Note: For CarPlay, Siri voice control must be enabled on your iPhone. If the interface doesn't appear, tap the ZLINK icon on the unit's screen.
Important Notes on Wireless Connectivity:
- When using wireless connectivity, your phone's Bluetooth may show as disconnected and Wi-Fi as off; this is normal as it switches to a local area network.
- Wireless connectivity supports navigation, music, and radio apps only; video apps are not supported.
- Connection methods may vary between Android phone brands due to system customization.
9. Screen Mirroring
The unit supports screen mirroring for both iOS and Android devices. You can switch between wired and wireless mirroring. For Android, download the 'zPLUS' app.
10. DSP (Digital Sound Processor)
Access DSP settings to adjust audio effects, EQ, surround sound, ultra-bass, and sound field balance.
11. Local Music and Videos
Play media from USB or TF card. Functions include loop playback, track/video navigation, playlist viewing, and sound effects.
12. Map Navigation
The unit supports map navigation (e.g., Google Maps, WAZE). Features include search, location display, route type selection, and personalized settings.
13. Steering Wheel Control Learning
You can configure the unit to respond to your vehicle's original steering wheel control buttons.
- Enter vehicle settings and switch to 'Learning' mode.
- Select the function icon you wish to learn (e.g., Volume +).
- Press the corresponding button on your steering wheel.
- After learning all buttons, select 'Return' to save settings.
Note: This function applies to models with steering wheel control buttons that do not have CAN-BUS.
14. In-Vehicle Settings
Access settings for general functions (radio, rearview, reverse assist lines), display (screen saver, wallpaper, brightness), sound (navigation, media, Bluetooth volume), factory settings (password: 6 zeros), and system information. Some models also support colorful button lights.
15. Touch Calibration
If touch abnormalities occur (deviation, reverse touch, no touch), perform calibration:
- After booting, press and hold the touch screen with five fingers for 5 seconds.
- Slightly move fingers to enter the calibration interface.
- Follow on-screen prompts to click the cursor in sequence. The system will return to the main interface upon completion.
16. Theme and File Manager
You can select your preferred theme. The file manager allows you to browse, copy, cut, delete, and paste files from USB devices.
Maintenance
This product is designed for minimal maintenance. Keep the screen clean with a soft, dry cloth. Avoid using abrasive cleaners or solvents. Ensure all connections are secure and free from corrosion. No user-serviceable parts inside.
Troubleshooting
- Unit does not power on: Recheck pre-installation test steps and all power connections. Ensure the 12V supply is active and grounded correctly.
- Touch screen unresponsive or inaccurate: Perform the touch calibration procedure as described in the 'Operating Instructions' section.
- No WiFi/Bluetooth signal: Ensure the rear view camera wire is connected, even if no camera is installed, as this affects signal integrity.
- CarPlay/Android Auto not connecting: Verify your phone's Wi-Fi and Bluetooth are on. For wired connections, use a high-quality data cable (preferably original). Check the ZLINK icon on the unit.
For common problem solutions, you may refer to the full user manual PDF available at ESSGOO User Manual (PDF).
Specifications
| Feature | Specification |
|---|---|
| System | WINCE |
| Screen Size | 7 inch HD Touchscreen |
| Screen Resolution | 1024*600 |
| Radio Frequency | 87.5-108MHz (FM1, FM2, FM3 bands, 18 preset stations) |
| Bluetooth Version | 5.1 |
| Max Power Output | 4 × 60W |
| Operating Voltage | DC 12V |
| Audio Format Support | MP3, WMA, WAV, FLAC, OGG, APE |
| Video Format Support | RM, RMVB, DVD (VOB), VCD (DAT), MP1, MP2, DIVX/XVID/MP4, H263, H264, FLV, MKV, 3GP, SWF, AVI, ASF, MJPEG |
| Image Format Support | JPEG |
| Special Features | WiFi function, Steering Wheel Control, CarPlay, Android Auto, Reversing Input |
| Item Weight | 1.3 kg |
| Dimensions (Approx.) | 7 inch (Width) × 4.1 inch (Height) × 1.7 inch (Depth) |
| OSD Language | Arabic, Irish, Belarusian, Bulgarian, Polish, Danish, German, Russian, French, Finnish, Korean, Dutch, Croatian, Latin, Malay, Japanese, Swedish, Slovenian, Ukrainian, Italian, English |

Warranty and Support
Warranty
This ESSGOO car stereo comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
Support
For any questions, technical assistance, or warranty inquiries, please contact ESSGOO customer service. You can also refer to the comprehensive user manual PDF for detailed instructions and troubleshooting guides:
User Tips
- Installation Patience: While installation can sometimes require a bit of figuring out, the unit integrates well, and features like steering wheel controls are confirmed to work effectively.
- Enhanced Features: Consider purchasing additional modules, such as for digital radio, to expand the unit's capabilities and enhance your in-car entertainment experience.
- Front USB Access: The unit is equipped with a convenient USB port on the front panel, allowing for easy connection of USB devices.