Dooya DC1680/DC1681

Contents

Dooya DC1680/DC1681 Wall Control Switch and Receiver User Manual

Models: DC1680 (Single Channel), DC1681 (Dual Channel)

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dooya DC1680 (Single Channel) and DC1681 (Dual Channel) Wall Control Switches and Receivers. These devices are designed to control four-wire curtain motors using RF433 technology, operating within an AC100-250V power supply range. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

2. Specifications

AttributeValue
Model NumberDooya DC1680/DC1681
Voltage110-240V AC
Wattage0W (Receiver only, controls motor)
OriginMainland China
CertificationCE
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
Battery IncludedNo
High-concerned chemicalNone

3. Product Overview

The Dooya DC1680 and DC1681 are wall-mounted control units designed for automated curtain systems. The DC1680 is a single-channel receiver, while the DC1681 is a dual-channel receiver, allowing control of one or two curtain motors respectively. Both units feature intuitive up, down, and stop buttons for local control.

Front view of Dooya DC1680 single-channel wall switch with up, down, and stop buttons.

Figure 1: Front view of Dooya DC1680 Wall Control Switch

Dooya DC1680 unit on its product box, showing the single-channel design.

Figure 2: Dooya DC1680 Single Channel Unit

Dooya DC1681 unit on its product box, showing the dual-channel design with two sets of up, down, and stop buttons.

Figure 3: Dooya DC1681 Dual Channel Unit

4. Installation

4.1 Wiring Connections

The receiver unit requires a 110-240V AC power supply and connects to a four-wire curtain motor. Ensure all power is disconnected before attempting any wiring.

Back view of Dooya DC1680 receiver showing wiring terminals labeled V, N, A, E, N, L.

Figure 4: Back view of DC1680 Receiver with Wiring Terminals

Side view of Dooya DC1680 receiver showing wiring terminals for power and motor connections.

Figure 5: Side view of DC1680 Receiver

4.2 Wiring Diagram (DC1680 Single Channel)

Refer to the diagram below for connecting the DC1680 single-channel wall-mounted receiver to a curtain motor and a DC1600 single-channel emitter. The system operates on 230V/50Hz.

Wiring diagram for Dooya DC1680 single-channel wall-mounted receiver. Shows connection from 230V/50Hz power to DC1680, and from DC1680 to a curtain motor. A DC1600 single-channel emitter is shown wirelessly communicating with the DC1680.

Figure 6: DC1680 Single-Channel Wiring Diagram

Wiring Terminal Labels:

  • L: Live wire (AC power input)
  • N: Neutral wire (AC power input)
  • E: Earth/Ground wire
  • A: Motor Up/Open control wire
  • V: Motor Down/Close control wire
  • N (Motor): Motor Neutral wire

Ensure all connections are secure and correctly matched to avoid damage to the device or motor, and to prevent electrical hazards.

5. Operation

5.1 Manual Control

The wall control switch features three buttons for direct operation:

  • Up Arrow (↑): Press to open/raise the curtain.
  • Dash (–): Press to stop the curtain at its current position.
  • Down Arrow (↓): Press to close/lower the curtain.

5.2 Remote Control (RF433 Emitter)

The receiver unit can be paired with a compatible RF433 emitter (e.g., Dooya DC1600) for wireless control. Refer to the emitter's manual for pairing instructions. Once paired, the emitter's buttons will replicate the functionality of the wall switch.

5.3 Smartphone App Control (if applicable)

Some Dooya systems support smartphone app control via a smart hub (sold separately). If your setup includes a compatible smart hub, you can control your curtains remotely through the dedicated app. The video below demonstrates this functionality.

Video 1: Demonstration of smart curtain control using a smartphone app.

6. Maintenance

  • Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
  • Do not use abrasive cleaners or solvents, as these can damage the surface.
  • Ensure the device is not exposed to excessive moisture or direct sunlight.
  • Regularly check wiring connections for any signs of wear or looseness.

7. Troubleshooting

  • Curtain motor not responding:
    • Check if the power supply to the receiver is active.
    • Verify all wiring connections are secure and correct according to the diagram.
    • Ensure the remote emitter (if used) has a working battery and is properly paired.
    • If using app control, check the smart hub's connection and app settings.
  • Buttons not responding:
    • Ensure the unit is receiving power.
    • Check for any physical obstructions or damage to the buttons.
  • Intermittent operation:
    • Check for sources of RF interference (e.g., other wireless devices).
    • Ensure the remote emitter is within range of the receiver.

8. User Tips

  • Remote Battery: The remote control (emitter) does not typically include batteries due to shipping restrictions. Please purchase the required battery type (usually a small coin cell or AAA, check your remote's specifications) from your local market.
  • Chromatic Aberration: Product photos are taken of real products, but slight color discrepancies may occur due to lighting conditions and computer screen settings.

9. Warranty and Support

For warranty information and technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.