NEEWER RS-60E3

Contents

Neewer LCD Timer Shutter Release Remote Control Cord RS-60E3

User Manual

1. Introduction

The Neewer RS-60E3 LCD Timer Shutter Release Remote Control Cord is a versatile accessory designed to enhance your photography by providing precise control over your camera's shutter. This digital timer remote allows for various advanced shooting modes, including self-timer, interval timer, long-exposure timer, and exposure-count settings. It functions as a full camera shutter switch, supporting both halfway (focus) and complete (shutter release) pressing actions. Its energy-saving design ensures long operational periods, making it ideal for group shots, macro photography, long exposures, continuous shooting, and motion capture.

Neewer LCD Timer Shutter Release Remote Control Cord RS-60E3

Figure 1: Neewer LCD Timer Shutter Release Remote Control Cord RS-60E3.

2. Product Overview

2.1 Key Features

  • Full Shutter Control: Supports half-press for autofocus and full-press for shutter release.
  • Programmable Timer Functions: Includes self-timer (DELAY), interval timer (INTVL), long-exposure timer (BULB/LONG), and exposure-count settings (N).
  • Wide Time Range: Timer settings from 1 second up to 99 hours, 59 minutes, 59 seconds.
  • Exposure Count: Allows setting up to 399 exposures.
  • LCD Display: Large, illuminated LCD screen for easy viewing of settings and status.
  • Ergonomic Design: Stylish and comfortable for single-thumb operation.
  • Energy Saving: Designed for extended use.

2.2 Components and Controls

The remote control features an intuitive layout for easy operation. Refer to the diagram below for an overview of the controls and display elements.

Diagram of RS-60E3 remote control with labeled buttons and LCD display elements

Figure 2: RS-60E3 Remote Control Function Diagram.

  1. Functional Cursor
  2. Time Display
  3. Lock Indication
  4. Low battery indicator
  5. Timer Active Instruction
  6. Sound On
  7. Set Instruction
  8. Shutter Release Display
  9. Number of shots (1-399 photos)
  10. Indicator Light (Yellow: Focus, Red: Trigger Shutter)
  11. LED Screen
  12. Lighting/Lock Button
  13. Cursor Control Button (Up, Down, Left, Right)
  14. SET Button
  15. HOLD Button
  16. Shutter-release Button (Halfway: Focus, Full Press: Trigger Shutter)
  17. Timer Start/Stop Button

3. Setup

3.1 Battery Installation

The RS-60E3 requires two (2) AAA 1.5V LR03 alkaline batteries (not included) for operation.

  1. Locate the battery compartment on the back of the remote control.
  2. Slide the battery compartment cover open.
  3. Insert two AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  4. Close the battery compartment cover securely.
Image showing the battery compartment, required AAA batteries, and a list of compatible camera models.

Figure 3: Battery installation and compatibility information.

3.2 Connecting to Your Camera

Connect the remote control to your camera's remote control terminal using the provided 90cm cord. The specific location of this terminal varies by camera model; consult your camera's manual if unsure.

3.3 Camera Compatibility

The Neewer RS-60E3 is designed as a replacement for the Canon RS-60E3 and is compatible with a wide range of cameras, including but not limited to:

  • Canon EOS: 10D, 7D, 30D, 33, EOS300, EOS50, 300D, 350D, 400D, 450D, XSi, 1000D, 500D, 550D, G10, G11, 600D, 60D, 650D, T3i, XD, 1100D, 700D, X2
  • Contax: 645, N1, NX, N
  • Pentax: K7, K5, IstD, IstDL, K10D, K200D, K100D, K100DL, MZ-6, ZX-L, MZ-L, K2000D, 645D
  • Samsung: GX 1L, GX 1S, GX 20, NX10, NX100
  • Hasselblad

4. Operating Instructions

4.1 Basic Shutter Release

To manually trigger the camera's shutter:

  1. Ensure the remote is connected to your camera and powered on.
  2. Half-press the Shutter-release Button (16) to activate your camera's autofocus. The yellow indicator light (10) may illuminate.
  3. Fully press the Shutter-release Button (16) to trigger the camera's shutter. The red indicator light (10) may illuminate.

4.2 Setting Timer Functions

The remote offers four main timer functions: Delay (Self-Timer), Long Exposure (BULB), Interval Timer, and Exposure Count. Use the Cursor Control Buttons (13) to navigate and the SET Button (14) to confirm settings on the LCD screen (11).

4.2.1 Delay / Self Timer (DELAY)

This function acts like a self-timer, delaying the shutter release by a set amount of time.

  • Set the desired delay time in 1-second increments, up to 99 hours, 59 minutes, 59 seconds.
  • Once set, pressing the Timer Start/Stop Button (17) will initiate the countdown before the shutter fires.

4.2.2 BULB / Long Exposure (LONG)

This mode allows for extended exposure times, ideal for capturing light trails, star photography, or low-light scenes.

  • Set the desired long exposure duration, up to 100 hours.
  • Alternatively, for manual bulb control, push the switch on the remote up to keep the shutter released for the desired duration, then push it down to close the shutter.
Examples of long exposure photography achieved using the BULB mode.

Figure 4: Creative photography examples using BULB mode.

4.2.3 Interval Timer (INTVL)

The interval timer allows you to take a series of photos at regular, predefined intervals.

  • Set the interval time, up to 100 hours. For example, setting it to 10 minutes will take one exposure every 10 minutes.
  • The remote will continue taking photos at the set interval until the camera's memory card is full or the Exposure Count limit is reached.
Diagram illustrating timing interval shooting with the remote connected to a camera.

Figure 5: Timing interval shooting setup.

4.2.4 Exposure Count (N)

This setting determines the total number of exposures the remote will trigger.

  • You can set the exposure count from 1 to 399 photos.
  • This works in conjunction with the Delay, Long Exposure, and Interval Timer functions to create automated shooting sequences.

4.3 Using the Lighting/Lock Button

The Lighting/Lock Button (12) serves two purposes:

  • Backlight: Press briefly to illuminate the LCD screen for easier viewing in low light conditions.
  • Lock: Press and hold to lock the current settings, preventing accidental changes during a shooting sequence.

5. Specifications

Feature Specification
Approximate Size 150 x 38 x 15 mm
Approximate Weight 72g
Battery Type 2 x AAA batteries (not included)
Approximate Cord Length 90cm
Timer Delay 1s to 99h 59m 59s
Long Exposure Time 1s to 99h 59m 59s
Interval Time 1s to 99h 59m 59s
Exposure Count 1 to 399 shots
Detailed close-up images of the remote's LCD display, standard plug, ergonomic design, and delicate texture.

Figure 6: Detailed views of the remote control's features.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the remote control. Do not use liquid cleaners or solvents.
  • Battery Replacement: Replace batteries when the low battery indicator (4) appears on the LCD screen. Always use fresh AAA alkaline batteries.
  • Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the remote in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Avoid dropping the remote or subjecting it to strong impacts, as this may damage internal components or the LCD screen.

7. Troubleshooting

  • Remote not responding:
    • Check if batteries are correctly installed and have sufficient charge. Replace if necessary.
    • Ensure the remote control cord is securely connected to both the remote and the camera.
    • Verify that the camera is powered on and set to a compatible shooting mode (e.g., Manual, Aperture Priority, Shutter Priority, or Bulb mode for long exposures).
  • LCD screen is blank or dim:
    • Replace batteries.
    • Press the Lighting/Lock Button (12) to activate the backlight.
  • Camera not focusing or firing:
    • Ensure the remote is fully connected.
    • Check camera settings for remote control compatibility.
    • Make sure the Shutter-release Button (16) is fully pressed for firing, and half-pressed for focusing.
  • Timer functions not working as expected:
    • Double-check all timer settings (Delay, Long Exposure, Interval, Exposure Count) on the LCD screen.
    • Ensure the timer is not locked (check Lock Indication 3).
    • Press the Timer Start/Stop Button (17) to initiate or stop the sequence.

8. User Tips

  • For long exposure photography, using a sturdy tripod is highly recommended to prevent camera shake and ensure sharp images.
  • When setting complex timer sequences, it's a good practice to test a short sequence first to ensure all settings are correct before committing to a long shoot.
  • Always carry spare AAA batteries, especially for extended shooting sessions or when traveling.
  • The anti-shake design of this remote helps in capturing clearer photos by eliminating camera movement caused by manually pressing the shutter button.
Comparison image demonstrating anti-shake effect with and without the shutter release.

Figure 7: Illustration of anti-shake benefits.

9. Warranty and Support

For warranty information or technical support, please refer to the documentation provided at the time of purchase or contact the manufacturer directly. Keep your proof of purchase for any warranty claims.

© 2023 Neewer. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.