DOOYA DM35EQL-8/17

Contents

Dooya Silent Tubular Motor DM35EQL-8/17 User Manual

Model: DM35EQL-8/17

Brand: DOOYA

1. Product Overview

The Dooya DM35EQL-8/17 is an electronic tubular motor designed for various rolling blinds. It features an integrated RF433 module and supports RS485 protocol for advanced control. This motor operates on 220V/230V at 50/60Hz and includes a 3-wire connection system.

Dooya DM35EQL-8/17 tubular motor with packaging and accessories
Dooya DM35EQL-8/17 tubular motor, packaging, and included accessories (crown and drive adapter).
Close-up of Dooya DM35EQL/J016-8/17 motor label with specifications and wiring diagram
Motor label detailing model, electrical specifications, and basic wiring.

2. Safety Information

  • It is strictly prohibited to beat the motor during transport, storage, installation, and use.
  • Minimize motor vibration during operation.
  • Ensure the power is off before performing any installation or maintenance.
  • This product complies with EU RoHS directives. Do not dispose of it as household waste. Please recycle it in accordance with local regulations for waste electrical and electronic equipment.

3. Installation

3.1. Crown and Drive Adapter Selection

The motor comes with a crown and drive adapter. The specific type provided depends on the rolling tube you intend to use. It is crucial to ensure compatibility with your tube's inner structure.

  • Different rolling tubes, even with the same outer diameter, may have varying inner structures.
  • You may need to modify the provided crown and drive adapter to fit your tube.
  • Alternatively, you can use 3D printed adapters or source compatible parts locally.
  • If your existing crown and drive adapter are in good condition and compatible, it is recommended to reuse them.
Diagram showing various tube types compatible with the motor, including 40mm Octagonal, 40mm Round, 45mm, 47mm Grooved, 50mm Round, and 50mm Grooved tubes.
Compatible tube types for the Dooya tubular motor.

Crown and Drive Adapter Examples:

  • For 40mm Round Tube:

    Crown and drive adapter for 40mm round tube
    Crown and drive adapter for 40mm round tube.
  • For 40mm Octagonal Tube:

    Crown and drive adapter for 40mm octagonal tube
    Crown and drive adapter for 40mm octagonal tube.
  • For 45mm Groove Tube:

    Crown and drive adapter for 45mm groove tube
    Crown and drive adapter for 45mm groove tube.
  • For 47mm Groove Tube:

    Crown and drive adapter for 47mm groove tube
    Crown and drive adapter for 47mm groove tube.
  • For 50mm Groove Tube:

    Crown and drive adapter for 50mm groove tube
    Crown and drive adapter for 50mm groove tube.
  • For 50mm Round Tube (Drive Adapter Only, No Crown Needed):

    Drive adapter for 50mm round tube
    Drive adapter for 50mm round tube (no crown required).

3.2. Drive Adapter Installation

Follow these steps to install the drive adapter into the tubular motor and then into the rolling tube.

Diagram illustrating the four steps for drive adapter installation: 1. Insert adapter into motor. 2. Push adapter fully in. 3. Measure length L. 4. Secure motor with rivets or screws into the tube.
Drive adapter installation process.

Warning: Forbidden to drill through the crown and inner gear wheel.

3.3. Bracket Installation

Mount the motor using appropriate brackets. Ensure secure fastening to prevent vibration and ensure proper operation.

Diagram showing two steps for bracket installation: 1. Attach brackets to the motor ends. 2. Secure the motor with attached brackets to the mounting surface.
Bracket installation for the tubular motor.

3.4. Circuit Installation (Wiring)

Connect the motor to the power supply and RS485 interface according to the diagram below. Ensure the power is off before wiring.

Wiring diagram for the Dooya tubular motor. Shows AC power input (230V/50Hz) with Blue (Neutral), Brown (Live), and Green/Yellow (Earth) wires, and an External RS485 Interface connection.
Circuit installation diagram for the motor.
  • Blue wire: Neutral
  • Brown wire: Live
  • Green/Yellow wire: Earth
  • Connect to an External RS485 Interface as needed.

4. Operation

4.1. Initial Setup and Pairing

This motor is an RS485 Electronic tubular motor with a built-in RF433 module. It can be controlled by RS485 or Dooya RF433 remote controllers (e.g., DC2700) or RF433 wall switches (e.g., DC1651).

Important: During settings, the time between two operations must be shorter than 6 seconds, otherwise it will exit the setting mode. If the motor has already been matched with a code, its memory will be cleared if you repeat the process.

Diagram showing the initial setup process for the motor. Steps include power cycling, pressing the motor's setting button, and using the P2 button on the remote control.
Initial motor setup and pairing with a remote.
  1. Switch off power for >10 seconds, then switch on. The motor will run for a hint.
  2. Press the setting button on the motor once. The motor will beep 3 times and run for a hint.
  3. Press the P2 button on the remote control once (motor beeps once).
  4. Press the P2 button on the remote control once again (motor beeps once).
  5. Press the P2 button on the remote control three times (motor beeps 3 times and runs for a hint).
  6. The setup is complete. The Up limit button controls the motor clockwise. The Down limit button controls the motor counter-clockwise.

4.2. Setting Up/Down Limit Positions

Note: It is invalid when the up limit and down limit are at the same location. After limit setting, with power and memory function, the motor will quit the setting limits status automatically into the match-code status 2 minutes later. The step-moving status allows for more precise adjustment.

Diagram illustrating the steps to set the upper and lower limit positions for the roller blind using a remote control.
Setting up the upper and lower limit positions.
  1. Set Up Limit Position:
    1. Press P2 button once (motor beeps once, runs for hint).
    2. Press Up button once (motor beeps 3 times, runs for hint).
    3. Adjust the blind to the desired up limit position using the remote.
    4. Press Stop button once (motor stops).
    5. The up limit is set.
  2. Set Down Limit Position:
    1. Press Down button once (motor runs for hint).
    2. Adjust the blind to the desired down limit position using the remote.
    3. Press Stop button five times (motor stops).
    4. The down limit is set.

4.3. Setting a Third Limit Position

After setting the up and down limits, you can set a third intermediate limit position.

Diagram showing how to set and cancel a third intermediate limit position for the roller blind.
Setting and cancelling the third limit position.
  1. To Set the Third Limit Position:
    1. Ensure up and down limits are already set.
    2. Press Stop button once (motor stops).
    3. Press P2 button once (motor beeps once).
    4. Press Stop button once (motor beeps once).
    5. Press P2 button three times (motor beeps 3 times, runs for hint).
    6. The third limit position is set.
  2. To Cancel the Third Limit Position:
    1. Power on the motor. The roller blind will move to the third limit.
    2. Press P2 button once (motor beeps once).
    3. Press P2 button once again (motor beeps once).
    4. Press P2 button three times (motor beeps 3 times, runs for hint).
    5. The third limit position is cancelled.

4.4. Adding/Deleting Emitters (Remote Controls)

Diagram showing steps to add a new remote control (emitter) or delete all paired remote controls from the motor's memory.
Adding and deleting emitters (remote controls).
  1. To Add an Emitter:
    1. Using an already matched remote (Emitter 'a'): Press P2 button once (motor beeps once).
    2. Press P2 button on Emitter 'a' once again (motor beeps once).
    3. Using the new remote (Emitter 'b'): Press P2 button three times (motor beeps 3 times, runs for hint).
    4. Emitter 'b' is now added.
  2. To Delete All Emitters:
    1. Press P2 button once (motor beeps once).
    2. Press Stop button once (motor beeps once).
    3. Press P2 button three times (motor beeps 3 times, runs for hint).
    4. All emitters are deleted from the motor's memory.

4.5. Setting Up with RS485

For control via RS485 protocol, follow these steps to enable communication.

Diagram showing how to set up the motor with an RS485 control system. Involves pressing the motor's setting button and observing the RS485 equipment's light.
Setting up with RS485.
  1. Press the setting button on the motor for 1 second. The motor will beep 3 times and run for a hint.
  2. Send open or close commands from your RS485 equipment.
  3. The RS485 equipment light should go out, indicating successful setup.

4.6. Light Adjust Function

This function allows adjustment of illumination if supported by your blind system.

Diagram showing how to activate and deactivate the light adjust function using the remote control.
Activating and deactivating the light adjust function.
  1. To Activate Light Adjust Function:
    1. Press P2 button once (motor beeps once).
    2. Press Up button once (motor beeps once).
    3. Press Down button three times (motor beeps 3 times, runs for hint).
    4. The light adjust function is now active. Short presses on Up/Down buttons adjust illumination with a 'dit' move; long presses (over 2 seconds) adjust continually.
  2. To Close Light Adjust Function:
    1. Press P2 button once (motor beeps once).
    2. Press Up button once (motor beeps once).
    3. Press Down button three times (motor beeps 3 times, runs for hint).
    4. The light adjust function is now closed.

5. Specifications

FeatureSpecification
Model NumberDM35EQL/J016-8/17 (also DM35EQL-8/17)
Rated Torque8 N.m
Rated Power98 W
Running Speed17 r/min
Rated Current0.43 A
Power Supply Voltage220V/230V
Frequency50/60 Hz
Operation TimeS2 4min
Protection GradeIP44
Insulation ClassH
Motor DiameterΦ35 mm
Communication MethodRS485 Protocol, RF433 Wireless
Control Range (Air)200 m
Control Range (Concrete Walls)35 m
Emission Frequency433.92 MHz
Max Channels20 (additional emitters needed for more)
Length498 mm
Weight1.54 kg (motor only) / 1.9 kg (package)
Diagram showing product parameters for DM35EQL/J, including rated torque, power, speed, current, voltage, protection grade, and features like RS485, wireless remote, percentage control, and quiet operation.
DM35EQL/J Product Parameters.
DM45EQ-J DM35EQ-J Tubular Motor Specification sheet, detailing technical support notes and control range with distances for air and concrete walls, and emission frequency.
DM45EQ-J DM35EQ-J Tubular Motor Specification.

6. Maintenance

To ensure the longevity and optimal performance of your Dooya tubular motor, consider the following general maintenance guidelines:

  • Keep the motor and surrounding area clean and free from dust and debris.
  • Avoid exposing the motor to excessive moisture or extreme temperatures.
  • Regularly check the wiring for any signs of wear or damage.
  • Ensure that the roller blind mechanism operates smoothly without obstruction, which could put undue strain on the motor.
  • Do not attempt to lubricate internal components unless specifically instructed by the manufacturer.

7. Troubleshooting

If you encounter issues with your motor, consider these basic troubleshooting steps:

  • Motor not responding: Check power supply. Ensure the remote control batteries are not depleted. Re-pair the remote control if necessary (refer to Section 4.1).
  • Blind not moving to correct limits: Re-set the upper and lower limit positions (refer to Section 4.2). Ensure no physical obstructions are preventing the blind from reaching its limits.
  • Motor making unusual noises: Check for any obstructions in the roller blind mechanism. Ensure the motor is securely mounted and not vibrating excessively.
  • Remote control issues: Verify the remote is within the effective control range (200m in air, 35m with concrete walls). Ensure no strong interference sources are nearby.

If problems persist, contact customer support or a qualified technician.

8. User Tips

  • For optimal performance and control, consider using official Dooya RF433 remote controllers or wall switches.
  • When dealing with different tube types, carefully verify the inner structure to ensure the correct crown and drive adapter are used or modified.
  • If you are comfortable with 3D printing, custom-made crown and drive adapters can be a viable solution for unique tube configurations.

9. Warranty and Support

This product has undergone EU conformity assessment and complies with the following directives:

  • Low Voltage Directive 2014/35/EU (LVD)
  • Electromagnetic Compatibility Directive 2014/30/EU (EMC)
  • Restriction of Hazardous Substances Directive 2011/65/EU (RoHS)
  • General Product Safety Regulation (GPSR)

The EU Declaration of Conformity (DoC) is issued, and technical documentation is kept by the EU Authorized Representative for inspection.

Manufacturer:

Name: Lumi United Technology Co., Ltd.

Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China

Tel: 86-18589043609

EU Authorized Representative:

Name: Sophie Bennett

Address: 9 rue du Bat d'Argent, 69001 Lyon, France

Tel: 33-774555006

Environmental Note:

This product complies with EU RoHS. Do not dispose of it as household waste. Please recycle it in accordance with local regulations for waste electrical and electronic equipment.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.