tungfull B1998

Contents

480W Electric Grinder Engraving Machine Mini Rotary Tool User Manual

Model: B1998 | Brand: tungfull

1. Introduction

This manual provides essential information for the safe and efficient operation of your new electric grinder and engraving machine. Please read all instructions carefully before use and retain this manual for future reference.

2. Safety Information

WARNING: Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle sharp/dangerous goods with care to avoid cuts or injuries.

3. Product Overview

The Tungfull B1998 is a versatile 480W electric rotary tool designed for various applications including grinding, engraving, sanding, polishing, drilling, cutting, and cleaning. It features a powerful pure copper motor and a 6-step speed adjustment for precise control.

Diagram of the electric grinder with labeled parts: Triangle chuck, Carbon Bush Mouth, 6 Speed Control, Power Switch, Hangable, Heat dissipation.
Figure 1: Product Components and Features
Close-up of the three-jaw chuck, showing its stable and durable design with a clamping range of 0.6-6.0mm.
Figure 2: Three-Jaw Chuck Detail
Diagram showing the flexible shaft accessory with its clamping range of 0.3-4.0mm and total length of approximately 110cm.
Figure 3: Flexible Shaft Accessory

4. Specifications

FeatureDetail
Model NumberB1998
Rated Input Power480W
Power SourceAC
Rated Voltage220V (EU Plug) / 110V (US Plug)
Frequency50/60Hz
No-load Speed5,000-26,700 r/min
Speed Adjustment6 steps variable speed
Chuck Clamping Range0.5-6.5 mm
Max. Drilling Diameter6.0 mm
Weight1 Kg
Power Cord Length1.5 m
CertificationCE
ApplicationJewelry tools, dental lab tools, polishing, engraving, drilling, cutting, cleaning
DIY SuppliesElectrical
Battery IncludedNo
OriginMainland China
Diagram showing product dimensions (60mm width, 260mm length) and key specifications: 480W power, AC power source, 220V or 110V voltage, 5,000-26,700r/min no-load speed, 0.5-6.5mm chuck, 1kg weight, 6-step variable speed.
Figure 4: Product Dimensions and Key Specifications
Image showing EU 220V and US 110V plug types, advising to select the correct product specifications before buying.
Figure 5: Available Plug Types (EU 220V / US 110V)

5. Setup and Operation

5.1. Initial Setup

  1. Unpacking: Carefully remove the tool and all accessories from the packaging.
  2. Protective Films: Remove any protective films from the device before first use.
  3. Power Connection: Ensure the power switch is in the "OFF" position. Connect the tool's power cord to an appropriate 220V (EU) or 110V (US) AC power outlet, matching your selected plug type.

5.2. Attaching Accessories

The tool features a three-jaw chuck for securely holding various accessories. A key wrench is provided for tightening and loosening the chuck.

Video 1: Demonstration of speed control, power switch, chuck operation, and accessory installation (e.g., cutting disc, protective cover).
  1. Open Chuck: Use the provided chuck key to loosen the three-jaw chuck by rotating it counter-clockwise until the jaws are wide enough to insert the accessory.
  2. Insert Accessory: Insert the shank of the desired accessory (e.g., grinding stone, drill bit, cutting disc) into the chuck. Ensure it is inserted far enough to be held securely.
  3. Tighten Chuck: Use the chuck key to tighten the chuck by rotating it clockwise until the accessory is firmly secured. Do not overtighten.
  4. Attach Protective Cover (for cutting/grinding): For operations like cutting or grinding, attach the transparent protective cover over the chuck area as shown in the video to enhance safety and contain debris.
A grid of nine images showing different accessories attached to the rotary tool: Grinding Stone, Steel Brush, Nylon Brush, Steel Brush (different type), Sanding Band, Diamond Burs, Buffer Wheel, Drill bits, Cutting Discs.
Figure 6: Various Compatible Accessories

5.3. Basic Operation

  1. Power On: Press and hold the power switch for approximately 3 seconds to turn on the device.
  2. Adjust Speed: Use the 6-step speed control dial to select the appropriate speed for your task. Start with a lower speed and gradually increase as needed.
  3. Perform Task: Apply gentle, consistent pressure while working. Allow the tool to do the work; do not force it.
  4. Power Off: After use, press and hold the power switch for 3 seconds to turn off the device.
Diagram of the electric grinder with labeled parts: Triangle chuck, Carbon Bush Mouth, 6 Speed Control, Power Switch, Hangable, Heat dissipation.
Figure 7: Speed Control and Power Switch Location

5.4. Applications

This multi-functional tool can be used for:

  • Cutting: Use cutting discs for thin metals, wood, and stone.
  • Polishing: Use buffer wheels or polishing pads for various materials.
  • Engraving: Use diamond burs for intricate designs.
  • Drilling: Use drill bits for wood, plastic, and soft metals.
  • Grinding/Sharpening: Use grinding stones for shaping and sharpening.
  • Cleaning: Use steel or nylon brushes for rust removal and surface cleaning.
Two images showing the tool in use: one for cutting a piece of wood with a circular saw blade, and another for polishing a piece of jade with a felt polishing bit.
Figure 8: Examples of Cutting and Polishing Applications
Two images showing the tool drilling: one drilling into a metal block, and another drilling into a metal pipe.
Figure 9: Examples of Drilling Applications

6. Maintenance

  • Cleaning: After each use, disconnect the tool from power and clean any dust or debris from the vents and chuck area using a soft brush or compressed air.
  • Storage: Store the tool and its accessories in a dry, clean place, away from direct sunlight and out of reach of children.
  • Carbon Brushes: Periodically check the carbon brushes for wear. Replace them if they are significantly worn to maintain optimal motor performance. (Refer to Figure 1 for Carbon Bush Mouth location).
  • Cord Inspection: Regularly inspect the power cord for any signs of damage. Do not use the tool if the cord is damaged.

7. Troubleshooting

  • Tool does not power on:
    • Ensure the power cord is securely plugged into a working outlet.
    • Check the power switch is in the "ON" position.
    • Verify the correct voltage (110V or 220V) is being supplied to the tool.
  • Reduced performance or unusual noise:
    • Check if the accessory is securely fastened in the chuck.
    • Ensure the correct speed setting is selected for the task.
    • Inspect carbon brushes for wear and replace if necessary.
    • Clean any debris from the motor vents to prevent overheating.
  • Excessive vibration:
    • Ensure the accessory is properly balanced and not bent or damaged.
    • Verify the accessory is correctly centered and tightened in the chuck.

8. User Tips

  • For delicate work, consider using the flexible shaft accessory for improved maneuverability and precision.
  • Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and a dust mask, especially during cutting, grinding, or sanding operations.
  • When working with different materials, experiment with various speed settings and accessories on a scrap piece first to find the optimal combination.
  • To prolong the life of your accessories, avoid excessive pressure and allow the tool's speed to do the work.

9. Compliance Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

The product is CE and RoHS certified. For detailed compliance and disposal information, please refer to the official user manual PDF.

Compliance markings including CE, UKCA, RoHS, and FCC, along with warnings about choking hazards and keeping out of reach of children.
Figure 10: Compliance Markings and Warnings

10. Warranty & Support

For detailed warranty information, troubleshooting guides, and customer support, please refer to the complete user manual available in PDF format:

Download User Manual (PDF)

You may also contact the manufacturer directly for support:

  • Manufacturer: ShenZhen Tungfull Digital Technology Co., Ltd
  • Email: 56827370@qq.com
  • Tel: 86-15089309815

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.