1. Introduction
Thank you for choosing the SAGE LU MEI ESP32 WLED LED Strip Light Controller. This advanced controller allows you to manage various addressable LED strips with extensive customization options through the WLED software. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure you get the most out of your device.
2. Safety Information
- Ensure the power supply voltage (DC 5-24V) matches the controller's requirements.
- Do not exceed the maximum total current of 15A.
- Disconnect power before making any wiring connections.
- Keep the device away from water, moisture, and high temperatures.
- Do not attempt to open or modify the controller, as this will void the warranty and may cause damage or injury.
- Ensure proper ventilation to prevent overheating.
3. Package Contents
Please check the package for the following items:
- 1x SAGE LU MEI ESP32 WLED LED Strip Light Controller (model as selected)
- 1x User Manual
4. Product Overview
The SAGE LU MEI WLED controllers come in several variants, each designed for specific needs:
- GL-C-618WL: White shell, 4 independent outputs, with Ethernet port.
- GL-C-616WL: Black shell, 2 independent outputs, with Ethernet port.
- GL-C-615WL: White shell, 2 independent outputs, no Ethernet port.
- GL-SW-001: Smart switch module (details not provided in source).
- GL-RC-002WL: Wireless remote control (compatible with WLED controller version 0.14.0-beta3 and above).

Figure 4.1: Product Details and Features
Highlights include a 20A pluggable fuse for overcurrent protection, excellent heat dissipation design, and reliable Wago terminals for secure connections.

Figure 4.2: Power Input Methods
The controller supports three power input methods: (1) V+, V- power interface, (2) 5.5x2.1mm DC Socket, and (3) Type-C interface (also used for UART download).

Figure 4.3: All-in-One Button Function
The integrated button provides quick control: 1. Short press: Power on/off. 2. Long press for 1 second: Switch colors. 3. Long press for 10 seconds: Reset the WLED controller and activate the WLED-AP hotspot.
5. Setup
5.1 Wiring the LED Strips
Ensure power is disconnected before wiring. Connect your addressable LED strips to the controller's output terminals (V+, GND, IOx) according to the number of strips you are using.

Figure 5.1: Wiring Diagram
Choose the correct wiring configuration based on the number of LED strips (one, two, three, or four) you intend to connect. Ensure V+ connects to V+, GND to GND, and data lines (IOx) to the data input of your LED strips.
5.2 Power Connection
Connect a DC 5-24V power supply to one of the input methods described in Figure 4.2. Ensure the power supply can provide sufficient current for all connected LED strips (up to 15A total).
5.3 Network Connection (for GL-C-616WL and GL-C-618WL)
Your controller can connect to your network via Wi-Fi or Ethernet.

Figure 5.2: Network Connection Methods
Connect via a standard Ethernet cable for wired connection or use the built-in Wi-Fi for wireless control.
For Ethernet Connection: Plug an Ethernet cable into the controller's port. In the WLED app, navigate to network settings and select 'Gledopto Series with Ethernet' as the Ethernet Type.

Figure 5.3: Ethernet Port Setup
Ensure the Ethernet Type is correctly selected in the WLED application settings for proper wired network functionality.
For Wi-Fi Connection: Power on the controller. If it's not already configured, it will broadcast a Wi-Fi access point (WLED-AP). Connect to this network from your phone/computer and navigate to http://4.3.2.1 in a web browser to configure your home Wi-Fi credentials.
5.4 DIY IO13 Port (Advanced)
The IO13 port can be used to connect external push switches, sensors, and other devices for custom control. This requires configuration within the WLED app's 'LED Preferences' and '2D Configuration' sections.

Figure 5.4: DIY IO13 Port Configuration
Connect a pushbutton or switch to the IO13 port. Configure its behavior in the WLED app under 'LED Preferences' and '2D Configuration' to assign functions like power on/off, color adjustment, mode change, or brightness control.
6. Operating Instructions
6.1 Basic Control (Using the Onboard Button)
Refer to Figure 4.3 for button functions:
- Short press: Power on/off.
- Long press (1 second): Switch between preset colors.
- Long press (10 seconds): Reset the controller to factory defaults and activate the WLED-AP hotspot for initial setup.
6.2 WLED App Control
The WLED app (available for iOS/Android or via web browser) provides comprehensive control over your LED strips:
- Dynamic Lighting Effects: Access over 100 integrated dynamic lighting effects.
- Segment Control: Create different lighting scenes and effects on various sections of a single LED strip or control multiple strips independently (requires segment setup in the app).
- Color and Brightness Adjustment: Fine-tune colors and brightness levels.
- Sync Lighting: Synchronize lighting effects across multiple controllers on the same Wi-Fi network.

Figure 6.1: Sync Lighting in WLED App
The WLED app allows you to synchronize lighting effects across multiple LED strips connected to the controller or other WLED devices on the same network.
6.3 Audio Reactive Lighting
The controller features a built-in microphone, enabling lighting effects to react to ambient sound or music. This feature can be configured and activated within the WLED app.

Figure 6.2: Microphone Function
Enjoy dynamic lighting that follows the rhythm of your music or ambient sounds.
6.4 Energy Saving Relay
The controller includes an energy-saving relay that significantly reduces standby power consumption by cutting power to the LED strip when turned off. This feature can be enabled and configured in the WLED app (typically via 'Relay GPIO 18').

Figure 6.3: Energy Saving Relay Setting
Configure the relay GPIO (e.g., GPIO 18) in the WLED app to enable low standby power consumption.
6.5 Remote Control (GL-RC-002WL)
If you have the GL-RC-002WL remote control, ensure your WLED controller firmware is version 0.14.0-beta3 or above for compatibility. Refer to the remote control's manual for specific pairing and operation instructions.
7. Maintenance
- Keep the controller clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to extreme temperatures or humidity.
- Ensure all connections are secure and free from corrosion.
- The 20A pluggable fuse can be replaced if it blows due to overcurrent. Ensure to replace it with a fuse of the same rating.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strips do not light up | No power; Incorrect wiring; Blown fuse; Controller not configured. | Check power supply and connections; Verify wiring according to Figure 5.1; Check and replace fuse if necessary; Ensure WLED app is configured correctly. |
| Controller not connecting to Wi-Fi/Ethernet | Incorrect network credentials; Router issues; Ethernet cable faulty; Incorrect WLED app settings. | Verify Wi-Fi password; Restart router; Check Ethernet cable; Ensure 'Ethernet Type' is set correctly in WLED app (Figure 5.3). |
| Lights flicker or behave erratically | Insufficient power supply; Loose connections; Data line interference. | Use a more powerful power supply; Secure all wiring connections; Keep data lines away from power lines. |
| Remote control not working | Controller firmware too old; Remote not paired; Batteries low. | Update controller firmware to 0.14.0-beta3 or newer; Pair remote according to its instructions; Replace remote batteries. |
9. Specifications
| Feature | Specification |
|---|---|
| Model Numbers | GL-C-618WL, GL-C-616WL, GL-C-615WL |
| Input Voltage | DC 5-24V |
| Max. Total Current | 15A |
| Output Channels | GL-C-615WL/616WL: 2 Outputs GL-C-618WL: 4 Outputs |
| Connectivity | Wi-Fi (all models), Ethernet (GL-C-616WL, GL-C-618WL) |
| Supported LED Strips | WS2811, WS2812, WS2812B, WS2813, WS2815, SK6812, SM16703P, GS8208, TM1814 Digital RGBIC Strip Light |
| Features | 20A Pluggable Fuse, Energy Saving Relay, Built-in Microphone, Type-C UART Port (for power/firmware), DIY IO13 Port |
| Operating Temperature | -20°C to 45°C |
| Dimensions | 129 x 50 x 23mm |

Figure 9.1: Supported Addressable LED Strip Types
The controller is compatible with a wide range of popular addressable LED strip protocols.
10. User Tips
No specific user tips were available from provided reviews or Q&A content.
11. Support Information
For further details, advanced configurations, or troubleshooting not covered in this manual, please refer to the official WLED documentation or the comprehensive user manual PDF provided by the seller: