DAKEFPV 5.8G 3W VTX

Contents

DAKEFPV 5.8G 3W VTX Video Transmitter User Manual

For RC FPV Racing Drones

1. Introduction

Thank you for choosing the DAKEFPV 5.8G 3W VTX Video Transmitter. This high-power video transmitter features a robust CNC shell, an integrated cooling fan, and a built-in microphone, making it ideal for long-range FPV applications and racing drones. This manual will guide you through the installation, operation, and maintenance of your VTX to ensure optimal performance and longevity.

DAKEFPV 5.8G 3W VTX with included accessories
Figure 1: DAKEFPV 5.8G 3W VTX with included accessories (antenna, wiring harness).

2. Specifications

Feature Detail
Model 5.8G 3W VTX
Frequency 5.8 GHz
Output Power Up to 3W
Shell Material CNC (Computer Numerical Control)
Cooling Built-in Fan
Audio Built-in Microphone
Control Interface IRC (SmartAudio/TrampHV compatible)
Antenna Connector SMA
Material Composite Material
Origin Mainland China
Recommended Age 14+ years
Use Vehicles & Remote Control Toys
Is Electric No Battery (requires external power)
Batteries Included No

3. Setup and Installation

Careful installation is crucial for the performance and reliability of your VTX. Follow these steps:

  1. Mounting: Securely mount the VTX to your drone frame using appropriate hardware. Ensure adequate airflow around the VTX, especially for the integrated fan, to prevent overheating.
  2. Antenna Connection: Connect a compatible 5.8G FPV antenna to the SMA connector on the VTX. Ensure the connection is tight but do not overtighten. Always connect the antenna before powering on the VTX to prevent damage.
  3. Wiring: Refer to the connection points on the VTX (DC, GND, IRC, VIDEO) and connect them to your flight controller or power distribution board as follows:
    • DC: Connect to a suitable power source (e.g., 7-26V, typically from your flight controller or PDB).
    • GND: Connect to ground.
    • VIDEO: Connect to the video output of your FPV camera.
    • IRC: Connect to a UART TX pad on your flight controller for SmartAudio/TrampHV control. This allows you to change VTX settings via your OSD or remote control.
  4. Microphone: The VTX has a built-in microphone. No additional connection is needed for audio transmission.
Bottom view of DAKEFPV VTX showing connection points
Figure 2: Bottom view of the DAKEFPV VTX, indicating DC, GND, IRC, VIDEO connections and the 'POWER BAND CHAN BUTTON'.
Side view of DAKEFPV VTX showing multi-pin connector and button
Figure 3: Side view of the DAKEFPV VTX, showing the multi-pin connector for power/signal and the 'POWER BAND CHAN BUTTON'.

4. Operating Instructions

4.1 Powering On

Once all connections are secure and the antenna is attached, power on your drone. The VTX will power on automatically. The integrated fan will activate to ensure proper cooling.

Angled view of DAKEFPV VTX showing cooling fan
Figure 4: Angled view of the DAKEFPV VTX, showing the integrated cooling fan.

4.2 Changing Channels, Bands, and Power Levels

The DAKEFPV VTX features a single 'POWER BAND CHAN BUTTON' for adjusting settings. The exact operation may vary slightly, but typically follows this pattern:

  • Short Press: A quick press and release of the button usually cycles through channels within the current band.
  • Medium Press (e.g., 2-3 seconds): Press and hold the button for a few seconds to cycle through available frequency bands.
  • Long Press (e.g., 5+ seconds): A longer press typically changes the VTX output power level. Be cautious when changing power levels, especially to higher settings, as this can generate more heat.

Note: Always refer to the LED indicators on the VTX (if present) to confirm the current channel, band, and power settings. For precise control and to avoid accidental changes, it is highly recommended to use SmartAudio/TrampHV control via your flight controller's OSD or remote control if configured.

Top view of DAKEFPV VTX showing 5G 3W marking
Figure 5: Top view of the DAKEFPV VTX, showing '5G 3W' marking and heat sink fins.

4.3 Built-in Microphone

The VTX includes a built-in microphone (indicated by 'MIC' on the device) to transmit audio along with the video feed. Ensure your FPV receiver and goggles/monitor support audio reception to utilize this feature.

Side view of DAKEFPV VTX highlighting SMA connector and MIC
Figure 6: Side view of the DAKEFPV VTX, highlighting the SMA antenna connector and the 'MIC' (microphone) port.

5. Maintenance

  • Keep Clean: Regularly clean the VTX, especially the fan and heatsink fins, to ensure efficient cooling. Use compressed air or a soft brush to remove dust and debris.
  • Check Connections: Periodically inspect all wiring connections for looseness or damage. Ensure the antenna is securely attached before every flight.
  • Heat Management: While the VTX has a built-in fan and CNC shell for cooling, avoid prolonged operation on the bench without adequate airflow, especially at high power settings.
  • Physical Inspection: Check the VTX for any physical damage, cracks, or bent pins after crashes or hard landings.

6. Troubleshooting

  • No Video Feed:
    • Ensure the VTX is powered correctly (DC and GND).
    • Verify the video input from the camera to the VTX is connected.
    • Check that your FPV receiver/goggles are on the correct frequency, band, and channel.
    • Confirm the antenna is securely attached to the VTX.
  • Poor Video Quality/Range:
    • Ensure both VTX and receiver antennas are of good quality and correctly oriented.
    • Check for interference from other electronic components on the drone.
    • Increase the VTX power level (if legally permitted and safe for your setup).
    • Verify the VTX is not overheating; ensure the fan is spinning and heatsink is clear.
  • VTX Overheating:
    • Ensure the integrated fan is operational and not obstructed.
    • Verify adequate airflow around the VTX.
    • Consider reducing the output power if high temperatures persist.
    • Never power on the VTX without an antenna connected.
  • SmartAudio/TrampHV Control Not Working:
    • Check the IRC wiring connection to your flight controller's UART TX pad.
    • Ensure the correct SmartAudio/TrampHV protocol is enabled and configured in your flight controller software (e.g., Betaflight).

7. User Tips

  • Antenna Quality: Invest in good quality 5.8G antennas for both your VTX and FPV receiver. This is one of the most significant factors for video range and clarity.
  • Power Management: While 3W offers extreme range, use the lowest power setting necessary for your flying environment to minimize heat generation and potential interference with other pilots.
  • Bench Testing: Always perform a quick bench test of your FPV system (VTX, camera, receiver) before flying to ensure everything is working correctly.
  • Legal Compliance: Be aware of and comply with local regulations regarding FPV video transmitter power output and frequency usage.

8. Warranty and Support

For warranty claims, technical support, or any questions not covered in this manual, please contact the seller or manufacturer directly. Keep your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.