SUMRY MPS-VIII ECO SERIES

Contents

SUMRY MPS-VIII ECO SERIES Hybrid Solar Inverter User Manual

Models: 3.6KW, 4.2KW, 6.2KW

Introduction

This manual provides essential information for the safe and efficient operation of your SUMRY MPS-VIII ECO SERIES Hybrid Solar Inverter. This series includes 3.6KW, 4.2KW, and 6.2KW models, designed for both on-grid and off-grid applications, featuring dual output and the ability to work without a battery. Please read this manual thoroughly before installation and use.

Important Safety Instructions

Please observe the following safety precautions to reduce the risk of electric shock, fire, or injury:

  • Read all instructions and cautionary markings on the unit and in this manual before operating.
  • Do not disassemble the inverter. Refer servicing to qualified service personnel.
  • Ensure all wiring is performed by a qualified electrician and complies with local electrical codes.
  • Do not connect the inverter to AC power sources that are not properly grounded.
  • Avoid installing the inverter in direct sunlight, near heat sources, or in environments with excessive moisture or dust.
  • Ensure adequate ventilation around the inverter to prevent overheating.

Product Overview

The SUMRY MPS-VIII ECO SERIES is a versatile hybrid solar inverter capable of managing power from solar panels, batteries, and the utility grid. Key features include:

  • On/Off Grid functionality
  • Dual output capability
  • Operation without battery (grid-tie mode)
  • High maximum solar charge current (up to 120A)
  • Wide PV input voltage range (up to 500VDC)
  • Available in 24VDC and 48VDC battery voltage options
  • Supports 50Hz/60Hz frequency ranges
SUMRY MPS-VIII ECO SERIES Solar Inverter with key features highlighted
Figure 1: SUMRY MPS-VIII ECO SERIES Hybrid Solar Inverter. This image displays the inverter unit and highlights its main features such as 4.2KW/6.2KW power, 230VAC voltage, 120A max solar charge current, 24V/48V battery voltage, 500VDC max PV input, and 50Hz/60Hz frequency range.

Setup and Installation

Proper installation is crucial for the safe and efficient operation of your inverter. It is highly recommended that installation be performed by a certified professional.

1. Site Selection

  • Install the inverter indoors, away from direct sunlight, rain, and excessive dust.
  • Ensure the ambient temperature is within the operating range of -10°C to 50°C.
  • Maintain adequate clearance around the inverter for proper airflow and heat dissipation.
  • Mount the inverter vertically on a sturdy wall or surface capable of supporting its weight (Net weight: 8.0-9.0 kgs).

2. Wiring Connections

All wiring must comply with local and national electrical codes. Ensure all power sources are disconnected before making any connections.

  1. PV Input (DC): Connect the solar panel array to the PV input terminals. Observe correct polarity. The maximum PV input voltage is 500VDC.
  2. Battery Connection: Connect the battery bank (24VDC or 48VDC) to the battery terminals. Ensure correct polarity and use appropriately sized cables.
  3. AC Input: Connect the utility grid AC power to the AC input terminals.
  4. AC Output: Connect your loads to the AC output terminals. The inverter provides 220-240VAC output.
  5. Grounding: Ensure the inverter chassis is properly grounded to a reliable earth ground.
  6. Communication Ports: Connect optional communication cables (RS232/RS485/WIFI/GPRS) for monitoring and control, if desired.

Operating Instructions

1. Initial Startup

  1. After all connections are securely made and verified, switch on the battery breaker (if applicable).
  2. Switch on the PV array breaker.
  3. Switch on the AC input breaker from the utility grid.
  4. Finally, switch on the inverter's main power switch. The inverter will perform a self-test and then begin operation.

2. Display Panel

The inverter features an integrated LCD display and control buttons for monitoring system status and configuring settings. Refer to the detailed product image for the location of the display.

The display typically shows:

  • Input voltage (PV, AC)
  • Output voltage and current
  • Battery status (voltage, charge/discharge current)
  • Operating mode (On-Grid, Off-Grid, Hybrid)
  • Fault codes or warnings

3. Operating Modes

The MPS-VIII ECO SERIES supports various operating modes, including:

  • On-Grid Mode: Inverter synchronizes with the utility grid, feeding excess solar power back to the grid or drawing power from it when solar generation is insufficient.
  • Off-Grid Mode: Inverter operates independently of the utility grid, providing power to connected loads from solar and/or battery storage.
  • Hybrid Mode: Combines features of both on-grid and off-grid, optimizing power usage from solar, battery, and grid based on user settings and availability.
  • Work without Battery: The inverter can operate in grid-tie mode directly from solar panels, without requiring a connected battery bank.

Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your SUMRY inverter.

  • Cleaning: Periodically clean the exterior of the inverter with a dry, soft cloth. Do not use liquid cleaners or solvents. Ensure ventilation openings are free from dust and debris.
  • Connection Checks: Annually, inspect all electrical connections (PV, battery, AC input/output, ground) for tightness and signs of corrosion. Tighten any loose connections.
  • Environmental Conditions: Ensure the operating environment remains within specified temperature (-10°C to 50°C) and humidity (5% to 95% non-condensing) ranges.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates for improved performance or new features.

Troubleshooting

If you encounter issues with your inverter, refer to the following basic troubleshooting steps. For complex problems, contact qualified service personnel.

  • No Power/Display Off: Check all power connections (PV, battery, AC input) and ensure all breakers are in the ON position. Verify battery voltage is within the acceptable range.
  • No AC Output: Check AC output breaker. Ensure the inverter is not in a fault state (check display for error codes). Verify PV input and battery charge.
  • Low Output Power: Check PV array for shading or damage. Ensure battery is fully charged and healthy. Verify load requirements do not exceed inverter capacity.
  • Overheating Warning: Ensure adequate ventilation around the inverter. Clean any dust from vents. Reduce load if operating continuously at maximum capacity in high ambient temperatures.
  • Communication Issues: Verify communication cables are securely connected. Check network settings if using WIFI/GPRS modules.

User Tips

  • Monitor Standby Power: Users often inquire about standby power consumption. While the inverter is designed for efficiency, monitoring its power draw during idle periods can help optimize overall system performance and energy savings. Utilize the communication ports (RS232/RS485/WIFI/GPRS) for detailed monitoring.
  • Battery Management: For models utilizing batteries, ensure proper battery maintenance and charging cycles to maximize battery lifespan and system reliability.

Specifications

The following tables provide detailed technical specifications for the SUMRY MPS-VIII ECO SERIES Hybrid Solar Inverter.

Product Data Sheet for SUMRY MPS-VIII ECO SERIES Inverter
Figure 2: Product Data Sheet outlining key specifications for MPS-VIII ECO 3.6KW, 4.2KW, and 6.2KW models, including PV input, grid-tie output, efficiency, two-load output, off-grid operation, battery charger, and hybrid operation details.
Detailed Specifications Table for SUMRY MPS-VIII ECO SERIES Inverter
Figure 3: Detailed specifications covering PV input, grid output, AC input, general physical dimensions, weight, interface (communication ports), and environmental conditions.

Table 1: General Specifications

Table 1: General Specifications
CategoryParameterValue
PV INPUT (DC)Nominal DC Voltage/Maximum DC Voltage360/500VDC
Start-up Voltage/Initial Feeding Voltage90VDC/120VDC
MPPT Voltage Range60-450VDC
GRID OUTPUT (AC)Nominal Output Voltage220/230/240VAC
Output Voltage Range195-253VAC
Nominal Output Current15.7A (3.6KW), 18.2A (4.2KW), 27.0A (6.2KW)
AC INPUTAC Start-up Voltage/Auto Restart Voltage120-140VAC/180VAC
Acceptable Input Voltage Range90-280VAC or 170-280VAC
Maximum AC Input Current21.1A (3.6KW), 24.7A (4.2KW), 36.4A (6.2KW)
Maximum AC Charging Current100A
GENERALDimension (D*W*H)(mm)420*350*110
Cartoon Dimension (D*W*H)(mm)500*415*180
Net Weight (kgs)8.0 (3.6KW/4.2KW), 8.9 (6.2KW)
Gross Weight (kgs)9.0 (3.6KW/4.2KW), 10.0 (6.2KW)
INTERFACECommunication PortRS232/RS485/WIFI/GPRS/LITHIUM BATTERY
ENVIRONMENTHumidity5% to 95% Relative Humidity (Non-condensing)
Operating Temperature-10°C to 50°C
STANDARDCompliance SafetyCE

Table 2: Product Data Sheet - MPS-VIII ECO Series

Table 2: Product Data Sheet - MPS-VIII ECO Series
MODELMPS-VIII ECO 3.6KWMPS-VIII ECO 4.2KWMPS-VIII ECO 6.2KW
Phase1-phase
Maximum PV Input Power6200W6500W6500W
Rated Output Power3600W/3600VA4200W/4200VA6200W/6200VA
Maximum Solar Charging Current120A80A120A
GRID-TIE OPERATION
PV INPUT (DC)Nominal DC Voltage/Maximum DC Voltage360/500VDC
Start-up Voltage/Initial Feeding Voltage60VDC/90VDC
MPPT Voltage Range60-450VDC
Maximum Input Current1/18A1/22A1/22A
GRID OUTPUT (AC)Nominal Output Voltage220/230/240VAC
Output Voltage Range195-253VAC
Nominal Output Current15.7A18.2A27.0A
Power Factor>0.99
EFFICIENCYMaximum Conversion Efficiency (DC/AC)98%
TWO LOAD OUTPUT POWER
Full Load3600W4200W6200W
Maximum Main Load3600W4200W6200W
Maximum Second Load (battery mode)1200W1400W2067W
Maximum Load Cut Off Voltage26VDC52VDC26VDC
Maximum Load Return Voltage27VDC54VDC27VDC
OFF-GRID OPERATION
AC INPUTAC Start-up Voltage/Auto Restart Voltage120-140VAC/180VAC
Acceptable Input Voltage Range90-280VAC or 170-280VAC
PV INPUT (DC)Nominal DC Voltage/Maximum DC Voltage360/500VDC
MPPT Voltage Range60-450VDC
Maximum Input Current1/18A1/22A1/22A
BATTERY MODE OUTPUT (AC)Nominal Output Voltage220/230/240VAC
Output WaveformPure sine wave
Efficiency (DC to AC)94%
BATTERY CHARGER
Nominal DC Voltage24VDC48VDC24VDC
Maximum Solar Charging Current120A80A120A
Maximum AC Charging Current100A60A100A
Maximum Solar+AC Charging Current120A80A120A
HYBRID OPERATION
Frequency Range59-61±1HZ

Warranty and Support

The SUMRY MPS-VIII ECO SERIES Hybrid Solar Inverter comes with a 1-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

For technical support, warranty claims, or service inquiries, please contact your authorized SUMRY dealer or the manufacturer directly. When contacting support, please have your inverter model number and purchase information ready.

The inverter is equipped with various communication ports (RS232, RS485, WIFI, GPRS) to facilitate remote monitoring and diagnostics, which can be helpful for support purposes.

Certifications: This product is certified with CE, RoHS, and FC standards, ensuring compliance with relevant safety and environmental regulations.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.