Introduction
Thank you for choosing the Gillaway Q10 Car Jump Starter with Air Compressor. This multifunctional device is designed to provide reliable jump-starting for vehicles, inflate tires, and serve as a portable power bank and LED flashlight. Please read this manual thoroughly before use to ensure safe and optimal performance.
Package Contents
Verify that all items listed below are included in your package:
- 1 x Gillaway Q10 Jump Starter with Air Compressor
- 1 x Smart Jumper Cable
- 1 x USB-A to USB-C Connection Cable
- 1 x Carrying Case
- 1 x Pump Tube (Trachea)
- 3 x Air Nozzles (Set of air nozzle)
- 1 x User Manual
Specifications
| Feature | Specification |
|---|---|
| Peak Starting Current | 4500 Amps |
| Vehicle Compatibility | 12V vehicles, up to 10L Gasoline / 8.0L Diesel engines |
| Starts per Charge | Up to 70 times |
| Air Compressor Pressure | 150 PSI |
| LED Light Output | 500 Lumens |
| LED Light Modes | Continuous, Strobe, SOS |
| USB Output | 2 USB ports for mobile device charging |
| Operating Temperature | Effective at -20°C (-4°F) |
| Battery Cycle Life | Over 10,000+ charge cycles |
| Number Of Built-in Batteries | 2 |
| Display | 5.1-inch Smart Screen with tire pressure detection |
| Safety Protections | Reverse polarity, anti-spark, short circuit, overcharge, overcurrent, low temperature, high temperature, overvoltage, overload, reverse charge |
Setup and Initial Charging
1. Initial Charging of the Jump Starter
Before first use, or if the device has been stored for a long time, fully charge the Gillaway Q10 jump starter. Use the provided USB-A to USB-C cable to connect the jump starter to a suitable USB power adapter (not included).
- The smart screen will indicate the charging status.
- Ensure the device is fully charged for optimal performance, especially for jump-starting.
2. Attaching Air Nozzles
Select the appropriate air nozzle from the provided set for the item you wish to inflate (e.g., car tire, bicycle tire, ball). Securely attach it to the pump tube (trachea).
Operating Instructions
1. Jump Starting a Vehicle
The Gillaway Q10 is designed to jump-start 12V vehicles with up to 10L gasoline or 8.0L diesel engines, even with completely dead batteries.
- Ensure the jump starter is sufficiently charged.
- Connect the smart jumper cable's blue plug into the jump starter's output port.
- Attach the red clamp (+) to the positive terminal of the vehicle's battery.
- Attach the black clamp (-) to the negative terminal of the vehicle's battery.
- Ensure the clamps are securely connected and there is no corrosion on the battery terminals.
- The smart jumper cable's indicator light will show the connection status. Follow the instructions on the smart cable if any errors are indicated.
- Start your vehicle.
- Once the vehicle starts, immediately remove the smart jumper cable from the vehicle battery, then disconnect it from the jump starter.
Safety Note: The Q10 features 10 built-in safety protection technologies including reverse polarity, anti-spark, short circuit, and overcharge protection to ensure safe operation.
2. Using the Tire Inflator
The integrated air compressor can inflate tires up to 150 PSI and features a smart digital display for precise control.
- Attach the pump tube to the jump starter's air output port.
- Select the appropriate air nozzle and attach it to the pump tube.
- Connect the nozzle to the tire valve or item to be inflated.
- Turn on the jump starter. The 5.1-inch smart screen will display the current tire pressure.
- Use the controls on the device to set the desired pressure and select the unit (PSI, BAR, KPA, Kg/cm2). The device supports inflation for cars, motorcycles, bicycles, and balls.
- Start the inflation process. The device will automatically stop when the preset pressure is reached.
- Disconnect the nozzle and store the pump tube and nozzles.
Important Note: Do not use the air pump function continuously for extended periods. If the tire battery compressor becomes seriously hot, allow it to cool down for a few minutes before resuming inflation to prevent damage.
3. Using the LED Flashlight
The 500 lumen LED light provides illumination and emergency signaling functions.
- Continuous Illumination: Press the light button once to turn on the steady light.
- Strobe Mode: Press the light button a second time for strobe light.
- SOS Mode: Press the light button a third time for SOS signaling.
- Press the button again to turn off the light.
4. Charging Mobile Devices
The Q10 can act as a portable power bank with two USB output ports.
- Connect your mobile device's charging cable to one of the USB output ports on the jump starter.
- The jump starter will automatically begin charging your device.
Maintenance
- Recharging: For optimal battery life and readiness, recharge the jump starter after each use, especially after jump-starting a vehicle. It is recommended to fully charge the device every 3-6 months if not used regularly.
- Cleaning: Wipe the device with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the jump starter and its accessories in the provided carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.
- Air Compressor Usage: Adhere to the cooling period for the air compressor as mentioned in the operating instructions to prevent overheating and prolong its lifespan.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Jump starter does not turn on. | Battery is depleted. | Charge the jump starter fully using the provided USB-C cable. |
| Vehicle does not start after jump-starting attempt. | Incorrect clamp connection; vehicle battery too severely discharged; other vehicle issues. | Ensure clamps are correctly attached (red to positive, black to negative). Check smart jumper cable indicator for errors. Allow a few minutes before re-attempting. If still unsuccessful, consult a mechanic. |
| Air compressor stops working or overheats. | Continuous use leading to overheating. | Allow the unit to cool down for several minutes before resuming operation. Avoid continuous use for prolonged periods. |
| Tire inflator not reaching desired pressure. | Air nozzle not securely attached; leak in pump tube or tire valve. | Ensure all connections are tight. Check for leaks. Verify correct pressure unit is selected. |
| Mobile devices not charging. | Jump starter battery low; incorrect cable; device not compatible. | Charge the jump starter. Use a known working USB cable. Ensure your device is compatible with standard USB charging. |
User Tips
- Always keep your Gillaway Q10 fully charged, especially before long trips, to ensure it's ready for emergencies.
- When jump-starting, ensure a clean connection to battery terminals for maximum efficiency.
- Utilize the various LED light modes (continuous, strobe, SOS) for roadside emergencies or as a general utility light.
- For tire inflation, always double-check the recommended PSI for your specific tire to avoid over-inflation.
- Store the device in its carrying case to protect it from dust and damage.
Warranty and Support
The Gillaway Q10 Car Jump Starter with Air Compressor comes with a 24-month warranty from the date of purchase.
Additionally, we offer lifetime technical support for this product. If you encounter any issues or have questions regarding the operation, maintenance, or troubleshooting of your device, please do not hesitate to contact our customer support team. Refer to your purchase documentation for contact details.
