HITBOX ARC200 MINI3

Contents

HITBOX ARC200 mini3 2-in-1 Welding Machine User Manual

Model: ARC200 MINI3

220V IGBT Inverter Hot Start Arc Force for Steel Iron

1. Introduction

Thank you for choosing the HITBOX ARC200 mini3 2-in-1 Welding Machine. This compact and lightweight inverter welder is designed for both MMA (Stick) and Lift TIG welding processes, offering excellent performance for various materials including mild steel, sheet metal, square pipe, cast iron, metal cage, and stainless steel. Featuring advanced IGBT inverter technology, Hot Start, Arc Force, Anti-stick, and VRD functions, this machine provides reliable and efficient welding capabilities.

HITBOX ARC200 mini3 Welder Dimensions and Weight

Figure 1: HITBOX ARC200 mini3 Welder, illustrating its ultra-portable design with dimensions (9.25in L, 5.9in H, 4.5in W) and weight (5.59 LBS).

ARC and Lift TIG Welding Modes in Operation

Figure 2: The welder supports both ARC (MMA) and Lift TIG welding modes. Note: A WP17V TIG torch needs to be purchased separately for Lift TIG operation.

2. Safety Precautions

  • Always wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Ensure proper ventilation in the welding area to avoid inhaling fumes.
  • Do not operate the machine in damp or wet conditions.
  • Ensure the machine is properly grounded.
  • Disconnect power before performing any maintenance or adjustments.
  • Keep children and unauthorized personnel away from the welding area.

3. Product Overview and Accessories

3.1 Panel Introduction

Front and Rear Panel Introduction

Figure 3: Front and Rear Panel Introduction

  1. Current Display
  2. MMA Function Indicator
  3. Lift TIG Function Indicator
  4. Power & Abnormal Indicator
  5. Mode Switching Button
  6. Current Regulation Knob (press to set function)
  7. "+" Output Connector
  8. "-" Output Connector
  9. Power Input
  10. Power ON/OFF Switch
  11. Cooling Fan

3.2 Included Accessories

Included Accessories

Figure 4: Standard accessories included with your welder.

  • Instruction Manual (this document)
  • 5 x Welding Rods
  • Cleaning Brush
  • Electrode Holder
  • Ground Clamp

4. Setup

4.1 Unpacking and Inspection

Carefully unpack the welding machine and all accessories. Inspect for any damage that may have occurred during transit. If any damage is found, contact your supplier immediately.

4.2 Power Connection

Connect the power input cable (9) to a suitable 220V power supply. Ensure the power source meets the machine's requirements and is properly grounded. This model is equipped with a UK Plug.

4.3 Welding Cable Connections

Proper connection of welding cables is crucial for safe and effective operation. Refer to the diagrams below for specific connections based on the welding mode.

4.3.1 Stick (MMA) Welding Connection

Stick (MMA) Connection Diagram

Figure 5: Stick (MMA) Welding Connection Diagram

  • Connect the Ground Clamp to the "-" Output Connector (8).
  • Connect the Electrode Holder to the "+" Output Connector (7).
  • Attach the ground clamp securely to the workpiece.
  • Insert the welding electrode into the electrode holder.

4.3.2 Lift TIG Welding Connection

Note: A TIG gun (WP17V torch) needs to be purchased separately for Lift TIG operation.

Lift TIG Connection Diagram

Figure 6: Lift TIG Welding Connection Diagram

  • Connect the Ground Clamp to the "+" Output Connector (7).
  • Connect the TIG Torch to the "-" Output Connector (8).
  • Attach the ground clamp securely to the workpiece.

5. Operating Instructions

5.1 Power On/Off

Flip the Power ON/OFF Switch (10) to turn the machine on or off. The Power & Abnormal Indicator (4) will illuminate when the machine is powered on.

5.2 Mode Selection

Press the Mode Switching Button (5) to toggle between MMA (Stick) welding mode and Lift TIG welding mode. The corresponding indicator (2 for MMA, 3 for Lift TIG) will light up on the digital display (1).

5.3 Current Regulation

Rotate the Current Regulation Knob (6) to adjust the welding current. The current value will be shown on the Current Display (1). Press the knob to set additional functions if available (e.g., Arc Force, Hot Start, Anti-stick, VRD).

Digital Display and Function Indicators

Figure 7: Digital Display showing current and function indicators.

5.4 Welding Features

  • Hot Start: Provides an initial boost of current to make arc striking easier, especially with difficult-to-start electrodes.
  • Arc Force: Prevents the electrode from sticking to the workpiece by increasing the current when the arc length becomes too short.
  • Anti-stick: Automatically reduces the current if the electrode sticks to the workpiece, allowing for easy removal without damaging the electrode or workpiece.
  • VRD (Voltage Reduction Device): Reduces the open-circuit voltage to a safe level when the machine is idle, enhancing user safety.
  • IGBT Technology: Ensures stable arc, high efficiency, and reliable performance.

5.5 Suitable Welding Materials

The HITBOX ARC200 mini3 is suitable for welding a variety of materials:

Suitable Welding Materials

Figure 8: Examples of materials suitable for welding with this machine.

  • Mild Steel
  • Sheet Metal
  • Square Pipe
  • Cast Iron
  • Metal Cage
  • Stainless Steel

6. Maintenance

  • Cleaning: Regularly clean the machine, especially the cooling fan (11) and ventilation openings, to prevent dust and debris buildup. Use the provided cleaning brush or compressed air.
  • Cable Inspection: Periodically check welding cables, electrode holder, and ground clamp for wear, damage, or loose connections. Replace damaged components immediately.
  • Storage: Store the welding machine in a dry, clean environment when not in use.
  • Professional Service: For any internal repairs or complex issues, contact qualified service personnel.

7. Troubleshooting

  • No Power: Check the power input cable (9) connection, the Power ON/OFF Switch (10), and the main power supply.
  • "ERR" Indicator (on display): If the "ERR" indicator illuminates, it typically signifies an internal fault or an overload condition. Turn off the machine, disconnect from power, wait a few minutes, and then restart. If the error persists, contact support.
  • Poor Arc/Sticking Electrode: Ensure proper current settings for the electrode size and material. Check for clean connections and a good ground clamp contact. The Anti-stick and Arc Force features should help mitigate these issues.
  • Overheating: If the machine stops during operation, it might be due to overheating. Allow the machine to cool down. Ensure the cooling fan (11) is unobstructed and functioning correctly.

8. Specifications

Feature Specification
Model Number ARC200 MINI3
Brand Name HITBOX
Input Voltage 220V
Welding Processes MMA (Stick), Lift TIG
Technology IGBT Inverter
Special Features Hot Start, Arc Force, Anti-stick, VRD
Dimensions (L x H x W) 9.25 in x 5.9 in x 4.5 in (approx.)
Weight 5.59 LBS (approx.)
Certification CE
Plug Type UK Plug

9. User Tips

  • Practice Makes Perfect: If new to welding, start with scrap materials to get a feel for the machine and different settings.
  • Electrode Selection: Choose the correct electrode type and diameter for your material thickness and desired weld properties.
  • Cleanliness: Always ensure the workpiece is clean and free of rust, paint, or oil for optimal weld quality.
  • Ground Connection: A strong, clean ground connection is vital for stable arc performance.
  • TIG Torch: Remember that a TIG torch is a separate purchase for Lift TIG welding. Ensure it is compatible with the machine.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2023 HITBOX. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.