1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your DIATONE MAMBA F55 or F65 128K AM32 4-in-1 Electronic Speed Controller (ESC). Please read this manual thoroughly before use to ensure safe and optimal performance.
2. Package Contents
- Main Product (DIATONE MAMBA F55 or F65 128K 4in1 ESC) × 1
- User Manual × 1
3. Safety Warnings
WARNING:
- Keep the product away from fire, high temperatures, and humidity.
- Keep out of reach of children and infants.
- This product contains small parts which may pose a choking hazard. Not suitable for children under 3 years.
- Do not disassemble, modify, or attempt to repair the product. Unauthorized modifications may void warranty and cause damage.
- Stop use immediately if the product appears damaged or malfunctions.
4. Product Overview
The DIATONE MAMBA F55 and F65 128K are high-performance 4-in-1 Electronic Speed Controllers designed for RC FPV racing drones. These ESCs feature AM32 firmware and support Dshot 300/600/1200 protocols, offering precise motor control and robust power delivery for 4-6S LiPo battery setups.

5. Specifications
5.1. MAMBA F55 128K ESC

| Feature | Specification |
|---|---|
| Working Voltage | 4 ~ 6S LiPo (16.8V ~ 25.2V) |
| Output Current | 55A × 4 |
| Peak Current | 65A (10S) |
| BEC Output | No |
| Firmware | AM32 MABA F55_128K |
| Protocol | DSHOT300/600/1200 |
| PWM Frequency | 24 ~ 128K |
| TVS Power Protection | Yes |
| Mounting Hole Size | 30.5mm × 30.5mm, Ø3 |
| Dimensions | 44.5mm × 40mm × 7.0mm |
| Weight | 15g |
| Telemetry | Yes |
5.2. MAMBA F65 128K ESC

| Feature | Specification |
|---|---|
| Working Voltage | 4 ~ 6S LiPo (16.8V ~ 25.2V) |
| Output Current | 65A × 4 |
| Peak Current | 75A (10S) |
| BEC Output | No |
| Firmware | AM32 MABA F65_128K |
| Protocol | DSHOT300/600/1200 |
| PWM Frequency | 24 ~ 128K |
| TVS Power Protection | Yes |
| Mounting Hole Size | 30.5mm × 30.5mm, Ø3 |
| Dimensions | 44.5mm × 40mm × 7.0mm |
| Weight | 15g |
| Telemetry | Yes |
6. Setup and Installation
The MAMBA F55/F65 128K ESCs are designed for a 30.5mm x 30.5mm mounting pattern with M3 screws. Refer to the wiring diagrams (Figure 2 for F55, Figure 3 for F65) for correct connection of motors, battery, and flight controller signals.
- Wiring: Connect motor wires (Motor 1-4), battery input (VCC, GND), and signal wires (S1-S4, TX, CURR) according to your flight controller's pinout and the ESC diagram.
- Capacitor Installation: A 35V 470µF capacitor is requested when using a 6S battery to help filter power and protect the ESC from voltage spikes. Ensure correct polarity when installing.
- Firmware: The ESC comes pre-installed with AM32 firmware (MABA F55_128K or MABA F65_128K). For advanced configuration or updates, refer to the AM32 firmware documentation.
7. Operating Instructions
These ESCs support DSHOT300, DSHOT600, and DSHOT1200 digital protocols. Ensure your flight controller is configured to use one of these protocols for optimal performance. The PWM frequency can operate between 24K and 128K.
- Flight Controller Integration: Connect the ESC to your flight controller using the appropriate signal wires (S1-S4).
- Telemetry: The ESC provides telemetry data (CURR, TX) which can be connected to your flight controller for real-time monitoring of current draw and other parameters.
- Configuration: Use compatible flight controller software (e.g., Betaflight, EmuFlight, ArduPilot) to configure motor directions, ESC protocols, and other settings.
8. Maintenance
- Keep the product clean and dry.
- Store the ESC in a cool and dry place when not in use.
- Avoid subjecting the ESC to strong pressure, dropping, or collision.
- Regularly inspect solder joints and wiring for any signs of damage or loose connections.
9. Troubleshooting
If you encounter issues with your ESC, consider the following general troubleshooting steps:
- No Motor Spin: Check all wiring connections, especially motor and signal wires. Ensure the flight controller is correctly configured for the Dshot protocol and motor outputs.
- Intermittent Operation: Inspect for loose solder joints or damaged wires. Verify battery voltage is within the specified 4-6S range.
- Overheating: Ensure adequate airflow around the ESC. Check for short circuits or motor issues that could cause excessive current draw.
- Firmware Issues: If experiencing unexpected behavior, consider reflashing the AM32 firmware using the appropriate tools and procedures.
For more detailed troubleshooting, consult online FPV communities or the official DIATONE support resources.
10. User Tips
No specific user tips were available from reviews or Q&A for this product. However, general tips for FPV ESCs include:
- Always double-check motor rotation direction in your flight controller software before maiden flight.
- Use high-quality solder and proper soldering techniques for all connections to prevent failures.
- Consider adding conformal coating to your ESC for extra protection against moisture and debris, especially if flying in wet conditions.
11. Compliance Information
- CE Compliance: This product complies with EU safety and environmental protection standards.
- FCC Statement: This device complies with Part 15 of FCC Rules.
- RoHS: This product is RoHS compliant.
12. Warranty and Support
For after-sale service or support, please contact the YUN FAN RC FPV Drone Store via the AliExpress platform. The product is manufactured in Mainland China.
A detailed user manual in PDF format is available for download: View User Manual (PDF).