Recordio GAW-V1633

Contents

Recordio GAW-V1633 UHF Wireless Microphone System User Manual

Model: GAW-V1633 | Brand: Recordio

Introduction

Thank you for choosing the Recordio GAW-V1633 UHF Wireless Microphone System. This professional 2-channel wireless system is designed to deliver clear and reliable audio performance for various applications, including schools, concerts, KTV stages, and public speaking events. This manual provides detailed instructions for setting up, operating, and maintaining your wireless microphone system to ensure optimal performance and longevity.

Safety Information

  • Read all instructions carefully before use.
  • Keep the product away from water, moisture, and extreme temperatures.
  • Do not attempt to disassemble or modify the unit. Refer all servicing to qualified personnel.
  • Use only the power adapter supplied with the unit.
  • Dispose of batteries responsibly according to local regulations.
  • Ensure proper ventilation around the receiver to prevent overheating.

Package Contents

Your Recordio GAW-V1633 system typically includes the following components:

  • 1 x UHF Wireless Receiver
  • 2 x Wireless Transmitters (Handheld Microphones, Lapel Microphones, Headset Microphones, or Conference Microphones, depending on your specific package)
  • 2 x Antennas
  • 1 x Power Adapter
  • 1 x Audio Output Cable (XLR to 1/4" or similar)
  • 1 x User Manual (this document)
  • AA Batteries (for transmitters, quantity may vary)
Recordio GAW-V1633 UHF Wireless Microphone System with receiver and two handheld microphones

Figure 1: Typical package contents showing the receiver and two handheld microphones.

Product Overview

Receiver

Front panel of the Recordio GAW-V1633 receiver with numbered components

Figure 2: Receiver Front Panel

  1. On/Off Power Button
  2. Infrared "IR" Frequency Comparison Window
  3. IR Frequency Key
  4. Multifunctional Display Screen
  5. Function Buttons (SET, Up, Down)
  6. Function Selection Key, Volume +/-
Rear panel of the Recordio GAW-V1633 receiver with input and output ports

Figure 3: Receiver Rear Panel

  1. DC-INPUT (Power Input 12~16V)
  2. BALANCED-A (XLR Output for Channel A)
  3. BALANCED-B (XLR Output for Channel B)
  4. MIX OUT (1/4" Mixed Output for both channels)
  5. ANT-A (Antenna Input for Channel A)
  6. ANT-B (Antenna Input for Channel B)

Transmitters

The system supports various transmitter types, including handheld, lapel, headset, and conference microphones. Each transmitter features an on/off switch and a display showing frequency and battery status.

Recordio receiver with two black handheld microphones

Figure 4: Handheld Microphones

Recordio receiver with two lapel microphones

Figure 5: Lapel Microphones

Recordio receiver with two headset microphones

Figure 6: Headset Microphones

Recordio receiver with two conference microphones

Figure 7: Conference Microphones

Setup Instructions

1. Receiver Connection

  1. Connect Antennas: Screw the two antennas into the ANT-A and ANT-B ports on the rear panel of the receiver. Position them vertically for best reception.
  2. Connect Power: Plug the supplied power adapter into the DC-INPUT port on the receiver and then into a suitable power outlet.
  3. Connect Audio Output:
    • For individual channel output, connect XLR cables from BALANCED-A and BALANCED-B to your mixer or amplifier.
    • For a mixed output of both channels, connect a 1/4" cable from the MIX OUT port to your mixer or amplifier.

2. Transmitter Battery Installation

Ensure correct polarity when inserting batteries.

Diagram showing how to install AA batteries into a handheld microphone

Figure 8: Handheld Microphone Battery Installation

  • Handheld Microphones: Unscrew the bottom part of the microphone to reveal the battery compartment. Insert 2 AA alkaline batteries, observing the correct polarity (+/-). Screw the bottom back on firmly.
  • Beltpack/Conference Transmitters: Open the battery compartment (usually a latch or slide mechanism). Insert 2 AA alkaline batteries, observing the correct polarity (+/-). Close the compartment securely.
Diagram showing how to install AA batteries into a beltpack transmitter

Figure 9: Beltpack Transmitter Battery Installation

3. Transmitter and Receiver Synchronization (IR Sync)

This feature automatically updates the bodypack or handheld transmitter settings to synchronize with the selected receiver channel.

  1. Open the transmitter battery cover (or front of the display) to expose the infrared (IR) port.
  2. Orient the infrared port towards the receiver's IR window (component 2 on Figure 2).
  3. On the receiver, select the desired channel using the Function Selection Key (6) or Function Buttons (5).
  4. Press the SYNC key (part of Function Buttons 5) once. The display screen will flash, indicating automatic infrared frequency alignment.
  5. The display on the receiver will indicate whether the synchronization was successful. If synchronization fails, please try the operation again and ensure that the infrared port on the transmitter is exposed and directly aimed at the infrared port of the receiver.
Diagram illustrating the infrared synchronization process between receiver and handheld microphone

Figure 10: Transmitter Synchronization

Operating Instructions

1. Power On/Off

  • Receiver: Press the On/Off Power Button (1 on Figure 2) on the receiver's front panel. The display will light up.
  • Transmitters: Slide the power switch on each microphone to the "ON" position. The microphone's display will show its operating frequency and battery status.

Video 1: Demonstration of receiver and microphone power-on and synchronization.

2. Channel Selection and Auto Scan

The receiver features an auto-scan function to find clear frequencies and IR sync for easy pairing.

  • Manual Channel Selection: Use the Function Selection Key (6) or the Up/Down buttons (part of 5) to manually change the channel on the receiver.
  • Auto Scan: Press the "SET" button (part of 5) to initiate an auto-scan for available frequencies. Once a clear frequency is found, use the IR sync process (described in Setup Instructions) to pair your transmitters.
Receiver display showing Infrared Sync and Auto Scan features

Figure 11: Receiver Characteristics - Infrared Sync and Auto Scan

3. Volume Adjustment

Adjust the output volume of each channel using the volume controls on the receiver (part of Function Selection Key 6).

Specifications

CategoryParameterValue
Comprehensive CharacteristicsCarrier frequency range610MHZ-960MHz (depending on applicable national regulations)
Bandwidth50MHz
Modulation methodFrequency Modulation (FM)
Maximum frequency deviation± 45KHz
Frequency response80Hz-15KHz
Signal to noise ratio (S/N)≥ 50dB (A)
Distortion (1kDz)≤ 2%
Working temperature-10 ℃ ~ 55 ℃
ReceiverOscillation modePLL (digital frequency synthesizer)
Spurious rejection≥80dB
Mirror Image Rejection≥80dB
Sensitivity5dB uV
Audio output level (balanced XLR)250mV/600Ω
Audio output level (unbalanced 1/4")400mV/3KΩ
Operating VoltageDC12~16V
Operating current≥500mA
Handheld TransmitterRF Power OutputMaximum 30mW (depending on applicable national specifications)
Oscillation modePLL (digital frequency synthesizer)
Transmitter frequency stability<30ppm
Dynamic range≥100dB(A)
Frequency Response50Hz-15KHz
Maximum input sound pressure130dB SPL
Microphone pickup headDynamic type
Power supply2 AA alkaline batteries
Beltpack/Conference TransmitterRF Power OutputMaximum 30mW (depending on applicable national specifications)
Oscillation modePLL (digital frequency synthesizer)
Transmitter frequency stability<30ppm
Dynamic range≥100dB(A)
Frequency Response50HZ-15KHz
Maximum input sound pressure130dB SPL
Microphone pickup headCondenser type
Power supply2 AA alkaline batteries
GeneralWorking distance80 meters (ideal environment)
Power consumption8W
Static power3W
Package Dimensions (10PCS/CTN)63.5 x 35 x 44.5 cm
Package Weight (10PCS/CTN)27 kg

Troubleshooting

  • No Sound:
    • Ensure the receiver and transmitters are powered on.
    • Check all cable connections between the receiver and your audio system.
    • Verify that the receiver and transmitters are synchronized to the same channel.
    • Adjust the volume levels on both the receiver and your audio system.
    • Check transmitter batteries and replace if low.
  • Interference or Poor Sound Quality:
    • Ensure antennas are properly connected and positioned.
    • Perform an auto-scan on the receiver to find a clear frequency and re-sync transmitters.
    • Reduce the distance between the transmitters and the receiver.
    • Avoid placing the receiver near other wireless devices, metal objects, or large crowds.
    • Ensure there is a clear line of sight between the transmitters and receiver antennas.
  • Transmitter Not Working:
    • Check if the transmitter is powered on.
    • Replace the batteries with fresh ones.
    • Re-synchronize the transmitter with the receiver.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the receiver and microphones. Do not use abrasive cleaners or solvents.
  • Battery Replacement: Replace transmitter batteries when the low battery indicator appears on the microphone display or when performance degrades. Always use high-quality AA alkaline batteries.
  • Storage: When not in use for extended periods, remove batteries from transmitters and store the system in a cool, dry place, away from direct sunlight and extreme temperatures.

User Tips

  • Line of Sight: Maintain a clear line of sight between the receiver antennas and the transmitters for optimal signal strength and range.
  • Fresh Batteries: Always start important events with fresh batteries in your transmitters to avoid unexpected power loss.
  • Gain Staging: Properly adjust the gain on your mixer or amplifier to prevent distortion and achieve the best sound quality.
  • Environmental Scan: Before each use, especially in new locations, perform an auto-scan to identify and use the clearest available frequencies.

Warranty & Support

This product comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support or warranty inquiries, please contact your retailer or the manufacturer directly. Do not attempt to disassemble the microphone privately, otherwise, the one-year warranty will not be available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.