Hantek MPO6104D

Contents

Hantek MPO6104D Multifunctional Oscilloscope User Manual

Model: MPO6104D

Brand: Hantek

1. Introduction

The Hantek MPO6104D is a powerful 6-in-1 multifunctional desktop oscilloscope designed for a wide range of electronic testing and analysis. It integrates a 4-channel oscilloscope, a 16-channel logic analyzer, a 2-channel signal generator, a digital voltmeter, a serial protocol analyzer, and an FFT spectrum analyzer. This device features a 7-inch capacitive touch screen for intuitive operation and offers advanced capabilities for waveform capture and analysis.

Front view of the Hantek MPO6104D multifunctional oscilloscope
Figure 1: Hantek MPO6104D Multifunctional Oscilloscope

Key Features:

  • Six-in-One Functionality: Combines a 4-channel oscilloscope, 16-channel logic analyzer, 2-channel signal generator, digital voltmeter, serial protocol analyzer, and FFT spectrum analysis.
  • High Performance: Waveform capture rate up to 400,000 frames per second (fast acquisition mode) with 256 levels of brightness and color temperature display.
  • Intuitive Display: 7-inch WVGA (800x480) capacitive touch screen for easy navigation and control.
  • Flexible Bandwidth: Available in 80MHz, 100MHz, and 200MHz models (MPO6104D is 100MHz).
  • Deep Storage: Storage depth up to 64Mpts.
  • Advanced Triggering: 16 triggering functions, including 5 protocol triggers, with options for Edge, Pulse, Video, Slope, Timeout, Window, Code, UART, LIN, CAN, SPI, and IIC triggers.
  • Standard Interfaces: USB Device, USB Host, LAN for versatile connectivity and remote control.

2. Package Contents

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your supplier.

  • 1 x Hantek MPO6104D Host Unit
  • 1 x USB PC Communication Cable
  • 4 x Oscilloscope Probes
  • 1 x 110-230V Wide Voltage Power Cable
  • 1 x Crocodile Clip Test Line
  • 1 x BNC to BNC Signal Cable
  • 4 x Logic Testing Modules
  • 4 x Power Cables (for logic modules)
  • 16 x Logic Test Heads
  • 1 x Certificate

3. Initial Setup

3.1 Power Connection

  1. Ensure the oscilloscope is placed on a stable, flat surface with adequate ventilation.
  2. Connect the provided 110-230V wide voltage power cable to the power input on the rear panel of the oscilloscope.
  3. Plug the other end of the power cable into a suitable AC power outlet.
  4. Press the power button on the front panel to turn on the device.

3.2 Connecting Probes and Cables

  • Oscilloscope Probes: Connect the oscilloscope probes to the BNC input connectors (CH1, CH2, CH3, CH4) on the front panel. Ensure a secure connection.
  • Signal Generator Output: For signal generation, connect the BNC to BNC signal cable to the "Gen1 Out" or "Gen2 Out" ports on the front panel.
  • Logic Analyzer: Connect the logic testing modules and logic test heads to the dedicated logic analyzer input ports.
  • USB PC Communication: Connect the USB Device interface on the back panel of the oscilloscope to a USB port on your computer using the USB PC communication cable for data transfer and control.
  • LAN Connection: Connect the LAN port on the back panel to your computer's network port using a standard network cable for network control.
Rear panel of the oscilloscope showing LAN/UART and USB Device ports
Figure 2: Rear Panel Interfaces (LAN/UART, USB Device)

4. Operating Instructions

4.1 7-inch LCD Touch Screen

The oscilloscope features a 7-inch WVGA (800x480) capacitive touch screen. This TFT widescreen display offers 256 levels of grayscale, realistic colors, and low power consumption. It supports a waveform capture rate of 60,000 wfms/s (dot display) in normal mode and up to 400,000 wfms/s in fast acquisition mode.

Close-up of the 7-inch LCD touch screen displaying a waveform
Figure 3: 7-inch LCD Touch Screen in operation
User interacting with the oscilloscope touch screen
Figure 4: Touch screen interaction

4.2 Pass/Fail Testing Function

The pass/fail testing function is used to evaluate signal quality in real-time. You can set specific rules for waveforms, and the oscilloscope will count the number of times tested, data frames passed/failed, and display the test results.

To enable Pass/Fail testing:

  1. Press the Utility button on the control panel.
  2. Navigate to 'Pass/Fail'.
  3. Select 'Test Enable'.
  4. Set the option to 'On'.
Screenshot showing the Pass/Fail testing function menu and instructions
Figure 5: Pass/Fail Testing Function Interface
Close-up of the oscilloscope control panel highlighting the Utility button
Figure 6: Location of the Utility Button

4.3 Triggering Functions

The MPO6104D offers 16 triggering functions, including 5 protocol triggers, to capture specific events in your signals. These include:

  • Edge Trigger
  • Pulse Trigger
  • Video Trigger
  • Slope Trigger
  • Timeout Trigger
  • Window Trigger
  • Code Trigger

Optional triggers for serial protocols include UART, LIN, CAN, SPI, and IIC.

Screenshot showing various trigger options on the oscilloscope display
Figure 7: Trigger Options (UART, LIN, CAN, SPI, IIC)

4.4 FFT Spectrum Analysis

The FFT (Fast Fourier Transform) spectrum analysis function uses simulated input channel waveforms to convert time-domain (YT) signals into their frequency components. This displays the relationship between dB V and frequency (Hertz), and the vertical reading changes from V to dB, allowing for detailed frequency domain analysis.

Screenshot of the oscilloscope displaying FFT spectrum analysis
Figure 8: FFT Spectrum Analysis Display
Oscilloscope screen showing both time-domain waveform and FFT spectrum
Figure 9: Combined Waveform and FFT Display

4.5 Segmented Collection Mode

Segmented storage allows for efficient data collection when multiple triggers are performed. Data from each trigger is stored in a dedicated segment. The oscilloscope supports 128Mpts and a segmented storage range of 1-8000 segments, with a single segment length of 32K, while maintaining a sampling rate of 1GSa/s.

Diagram illustrating the segmented collection mode
Figure 10: Segmented Collection Mode Diagram

4.6 Arbitrary Signal Generator

The integrated 2-channel signal generator can produce a variety of standard and arbitrary waveforms with a sampling rate of 200MSa/s and 12-bit vertical resolution. The frequency range is up to 25 MHz.

Standard Waveforms: Sine wave, Square wave, Pulse, Triangle wave, Noise, DC, Sinc, Exp, Haver Sine, Lorentz, Dual Tone Multi-frequency, Gauss, ECG signal.

Arbitrary Waveforms: Arb1, Arb2, Arb3, Arb4.

Refer to the "Specifications" section for detailed frequency characteristics of each waveform.

5. Interface and Controls

The MPO6104D features a combination of physical buttons, rotary encoders, and a touch screen for comprehensive control.

5.1 Front Panel Controls

The front panel includes dedicated buttons for common functions such as Menu, Default, Help, Cursors, Measure, Display, Wave Gen, Save/Recall, Run/Stop, Single, Auto Scale, and Utility. Rotary encoders are provided for adjusting Vertical, Horizontal, and Trigger settings for each channel.

Front view of the Hantek MPO6104D showing all controls
Figure 11: Front Panel Controls Overview

5.2 Rear Panel Interfaces

The rear panel provides connectivity options for external devices and remote control:

  • USB Device: For connecting to a PC for data transfer and software control.
  • USB Host: For connecting USB storage devices (e.g., flash drives) to save waveforms or settings.
  • LAN: For network connectivity, enabling remote control and data sharing over a local area network.
  • Power Input: For connecting the AC power cable.
Rear panel of the oscilloscope showing LAN/UART and USB Device ports
Figure 12: Rear Panel Interfaces

6. Specifications

6.1 Acquisition

ParameterDescription
Acquisition methodNormal, average, peak, high resolution
Real-time sampling rate1 G Sa/s (single channel)
500 M Sa/s (dual channel)
250 M Sa/s (three / four channels)
Peak DetectAnalog Channel 4ns
Averaging modeN samples for analog channels (N values: 2, 4, 8, 16, 32, 64, 128, 256, 512, and 1024)
High resolution12bit
Minimum detection pulse width8ns
Memory DepthSingle Channel 64M / 128M [EDU]
Dual channel 32M / 64M [EDU]
Three or four channels 16M / 32M [EDU]
Table of Acquisition, Input, and Horizontal specifications
Figure 13: Acquisition Specifications

6.2 Input

ParameterDescription
Number of channels4 analog channels, 16 (4 * 4) digital channels
The number of analog and digital channels opened at the same time should be less than 4.
Input couplingDC, AC or GND
Digital channels are not supported
Input resistanceAnalog channel: 25pF ± 3pF, 1MΩ ± 2%
DC couplingDigital channels: (300KΩ ± 2%), (8 pF ± 3 pF)
Support probe attenuation coefficientAnalog channels 0.01X, 0.02X, 0.05X, 0.1X, 0.2X, 0.5X, 1X, 2X, 5X, 10X, 20X, 50X, 100X, 200X, 500X, 1000X, 2000X, 5000X, 10000X
Voltage rating300V CAT II
Input voltageAnalog channels 300VRMS (10X)
Digital channel -25V ~ 25V

6.3 Horizontal

ParameterDescription
Waveform InterpolationSine, Linear, Step
Horizontal scale2ns/div ~ 100s/div 1,2,5 steps
Time base modeY-T, X-Y, Roll
X-Y number1, 2 channel combination 1 XY
3, 4 channels combined 1 XY
Zero offset± 0.5 div × minimum time base scale
Sampling rate and delay±25ppm
Clock drift≤±5 ppm/year
Incremental time measurement accuracy (Full bandwidth)± (1 sampling interval + 100ppm × reading + 0.6ns) > 16 times average
± (1 sampling interval + 100ppm × reading + 0.4ns)
Sampling interval = seconds / div ÷ 200

6.4 Vertical

ParameterDescription
Bandwidth (-3db)DPO6084: 80MHz
DPO6104: 100MHz
DPO6204: 200MHz
Vertical resolutionAnalog channel 8bit
Digital channel 1bit
Vertical scale500µV/div ~ 10V/div at input BNC
500µV/div to 128mV/div, ±1V
129mV/div to 1.28V/div, ±10V
1.29V/div to 10V/div, ±50V
Position range± 0.5 div × minimum time base scale
Selectable analog bandwidth limit, typically20MHz
Low frequency response (-3db)≤10Hz at BNC
Rise time at BNC, typicalDSO6084: ≤4.4ns
DSO6104: ≤3.5ns
DSO6204: ≤1.8ns
Vertical gain accuracyIn the "normal" or "average" acquisition mode, the accuracy from 10V/div to 10mV/div is ± 3%.
In "normal" or "average" acquisition mode, the accuracy from 5mV/div to 500uV/div is ± 4%.
DC offset accuracy± 0.1div ± 2 mV ± 1% offset value
Channel IsolationDC to Maximum Bandwidth: > 40 dB

Note: The bandwidth is reduced to 6MHz when using the X1 probe.

6.5 Vertical (Digital Channel: for MPO6000D / MPO600EDU / DPO6000B / DPO6000C purchase digital probe LP104)

ParameterDescription
ThresholdAdjustable threshold for 4 channels as a group
Threshold selectionTTL (1.4 V)
5.0 V CMOS (+2.5 V)
3.3 V CMOS (+1.65 V)
2.5 V CMOS (+1.25 V)
1.8 V CMOS (+0.9 V)
ECL (-1.3 V)
PECL (+3.7 V)
LVDS (+1.2 V)
0V
Custom
Table of Vertical, Display, and Interface specifications
Figure 14: Vertical and Digital Channel Specifications

6.6 Arbitrary Signal Generator (with signal source series)

ParameterDescription
Number of channels2/3 channels (Arb1, Arb2, Arb3, Arb4)
Sampling rate200MSa/s
Vertical resolution12 bits
Frequency25 MHz
Standard waveformsine wave, square wave, pulse, triangle wave, noise, DC, Sinc, Exp, Haver Sine, Lorentz, dual tone multi-frequency, Gauss, ECG signal
Arbitrary waveformArb1, Arb2, Arb3, Arb4
Frequency characteristics
Sine wave1uHz~25MHz
Square wave1uHz~15MHz
Pulse1uHz~5MHz
Triangle wave1uHz~1MHz
Noise1uHz~5MHz
Sinc1uHz~5MHz
Exp1uHz~5MHz
Haver Sine1uHz~5MHz
Lorentz1uHz~5MHz
dual tone multi-frequency1uHz~5MHz
Gauss1uHz~5MHz
ECG1uHz~5MHz
Arbitrary wave
Wave Length8KSa
Frequency Range1uHz~75MHz (less than 10 kHz) 50 ppm (more than 10 kHz)
Frequency Resolution0.1 Hz or 4 bits, whichever is greater
Amplitude Output range10mV~7Vpp (high impedance)
5mV~3.5Vpp(50Ω)
DC offset Range± 7 V, high impedance
± 3.5 V, 50 Ω
DC offset Resolution100 µV or 3 bits, whichever is greater
DC offset Accuracy2% (1 kHz)
Output impedance50 Ω, high impedance
Table of Arbitrary Signal Generator specifications
Figure 15: Arbitrary Signal Generator Specifications

6.7 General Technical Specifications

ParameterDescription
Probe compensator outputOutput voltage, typical: 2Vpp input ≥1MΩ load
Frequency, typical: 1kHz
Power supply voltage100-120VACRMS (± 10%), 45Hz to 440Hz, CAT II
120-240VACRMS (± 10%), 45Hz to 66Hz, CAT II
Power consumptionless than 30W
FuseT, 3.15A, 250V, 5x20mm
Surroundings
Operating temperature0~50 °C (32~122 °F)
Storage temperature-40~+71 °C (-40~159.8 °F)
Humidity≤ + 104 °F (≤ + 40 °C): ≤90% relative humidity
106 °F ~ 122 °F (+ 41 °C ~ 50 °C): ≤60% relative humidity
Cooling methodConvection
Altitudewith and without operation: 3000m (10,000 feet)
Mechanical shock
Random vibration0.31 g RMS from 50Hz to 500Hz, 10 minutes per axis
when not operating2.46g RMS from 5Hz to 500Hz, 10 minutes per axis
during operation50g, 11ms, half sine wave
Mechanical part
Oscilloscope size318 x 140 x 150mm (length x width x height)
Weight2900g
Table of General Technical Specifications
Figure 16: General Technical Specifications

6.8 Display

ParameterDescription
Display Type7" TFT LCD Diagonal
Display resolution800 (horizontal) * 480 (vertical) pixels
Display color16 million colors (24 bit true color)
Persist timeMin, 1 s, 5 s, 10 s, 30s, infinite
Display typePoint, vector
Display modeColor grade
Display brightnessAdjustable
Grid TypeOptional
Grid brightnessAdjustable
Waveform brightnessAdjustable

6.9 Interface

ParameterDescription
Standard interfaceUSB Host, USB Device, LAN, WIFI (EDU model)
Optional interfaceAux trigger output / pass failure (MPO6000EDU model)
UART
HDMI

7. Maintenance

7.1 General Care

  • Keep the oscilloscope clean and free from dust. Use a soft, dry cloth for cleaning the exterior.
  • Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
  • Ensure proper ventilation around the unit to prevent overheating.
  • Do not use abrasive cleaners or solvents that could damage the casing or screen.

7.2 Safety Precautions

  • Do not attempt to open the device casing. There are no user-serviceable parts inside, and doing so may void your warranty and expose you to hazardous voltages.
  • Always disconnect the power cable before cleaning or moving the device.
  • Use only the provided power cable and accessories.

8. Troubleshooting

This section provides solutions to common issues you might encounter. If the problem persists, please contact technical support.

8.1 Device Does Not Power On

  • Check if the power cable is securely connected to both the oscilloscope and the power outlet.
  • Verify that the power outlet is functional by plugging in another device.
  • Ensure the power switch on the oscilloscope is in the 'On' position.
  • Check the fuse (T, 3.15A, 250V, 5x20mm) on the rear panel. Replace if blown, but only if you are qualified to do so.

8.2 No Waveform Display

  • Ensure probes are correctly connected to the input channels and the circuit under test.
  • Check probe compensation and attenuation settings.
  • Adjust the vertical scale (Volts/Div) and horizontal scale (Time/Div) to an appropriate range for your signal.
  • Press the 'Auto Scale' button to automatically adjust settings for a stable waveform display.
  • Verify trigger settings. If the trigger level is outside the signal range, no stable waveform will be displayed.

8.3 PC Communication Issues

  • Ensure the USB PC Communication Cable is correctly connected to the 'USB Device' port on the oscilloscope and a USB port on your computer.
  • Install the necessary drivers for the oscilloscope on your computer.
  • Verify that the control software on your PC is correctly configured to detect the device.
  • For LAN connection, ensure the network cable is properly connected and network settings (IP address, subnet mask) are correct.

9. User Tips

  • Probe Compensation: Regularly check and adjust probe compensation for accurate measurements, especially when using new probes or after significant temperature changes.
  • Firmware Updates: Check the manufacturer's website periodically for firmware updates to ensure optimal performance and access to new features.
  • Screen Calibration: If touch screen responsiveness seems off, check for a screen calibration option in the Utility menu.

10. Warranty and Support

10.1 Product Warranty

This product comes with a one-year warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.

Our products are manufactured under a strict quality control system, with a pass rate consistently maintained over 99.8%.

10.2 Technical Support

For technical assistance, troubleshooting, or any inquiries regarding your Hantek MPO6104D oscilloscope, please contact our support team:

  • Whatsapp/Tel/Wechat: +8619902906050
  • Web: http://www.thanksbuyer.com
  • Address: Room 303 Building 2, Youpin Cultural and Creative Park, Zhangkeng, Minzhi Street, Longhua District, 518131, Shenzhen, China (Mainland)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.