Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Pinmany RZ-MZD61 CAN Bus Decoder. This device is designed to integrate with Android head units in specific Mazda RX8 models, enabling communication between the vehicle's CAN Bus system and the aftermarket head unit.
Image: Two views of the Pinmany RZ-MZD61 CAN Bus Decoder, showing model number and compatibility for Mazda RX8 2001-2011.
Setup and Installation
Pre-Installation Considerations
- This product functions as a Car Android Head unit CAN Bus adapter decoder.
- Ensure the operating voltage is within +9V to +16V. Voltages outside this range can damage the decoder.
- The decoder features 18-pin and 20-pin connectors with a pin pitch of 2.0mm.
- This CAN Bus decoder does not include cables. If you do not have suitable connection cables, it is recommended to purchase a CAN Bus adapter with cables.
- Professional knowledge is required for wiring. Always follow the provided pin function description for wiring to prevent damage.
- Before purchasing, verify compatibility by operating your Android radio to enter the CAN Bus setting screen and confirm your car model can be displayed.
- If you are unsure about fitting, contact support before purchase.
Image: Pre-purchase tips highlighting that cables are not included, the need for an 8-pin connector for serial communication, and the importance of professional wiring knowledge.
Step 1: Connection of Cable Adapter
- Identify the 16-pin and 20-pin CAN plug of your wire harness.
- Plug these into the corresponding 16-pin and 20-pin sockets of the CAN Bus Box.
Image: Diagram showing how to connect the 16-pin and 20-pin wire harness plugs into the CAN Bus Box.
Pin Definition
Refer to the following pin definition for proper wiring:
Image: Detailed pinout diagram for the 18-pin and 20-pin connectors of the RZ-MZD61 CAN Bus Decoder.
| Pin No. | Definition | Pin No. | Definition |
|---|---|---|---|
| 1 | GND | 11 | CLK |
| 2 | BATT(+12V) | 12 | ACC-IN |
| 3 | CAN-H | 13 | UART-RX |
| 4 | CAN-L | 14 | UART-TX |
| 5 | ILL-OUT1(PWM) | 15 | DATA1 |
| 6 | LCD-DET | 16 | DATA2 |
| 7 | KB/LCD PWR+5V | 17 | CS1 |
| 8 | NC | 18 | CS2 |
| 9 | SWC-IN | 19 | ILL-IN(PWM) |
| 10 | LCD PWR+8V | 20 | ILL-OUT2(PWM) |
18-pin Connector Pinout:
- Pins 1-16: NC (No Connection)
- Pin 17: UART2-TX
- Pin 18: UART2-RX
Head Unit Compatibility
The RZ-MZD61 CAN Bus Decoder is compatible with 7, 8, 9, and 10-inch Android Head units.
Image: Visual representation of 7, 8, 9, and 10-inch Android head units, indicating compatibility.
Suitable Car Models
This CAN Bus Decoder is specifically designed for Mazda RX8 models manufactured between 2001 and 2011.
Operating Instructions
Setting up CAN Bus on Android Head Unit
The following steps demonstrate the general setup method. Actual steps may vary depending on your specific Android head unit model. Consult your head unit vendor if needed.
- Enter Settings: Navigate to the main settings menu on your Android head unit.
- Enter Factory Settings: Locate and enter the 'Factory' settings menu.
- Enter Factory Password: If prompted, enter one of the common factory passwords: 3368, 1617, 8317, or 8888. If these do not work, consult the seller of your Android radio for the correct password.
- Enter CAN Bus Setting: Within the factory settings, find and enter the 'CAN Bus setting' or 'CarType Setting' menu.
- Select CAN Bus Box Manufacturer: Choose 'Raise' as the CAN Bus Box manufacturer.
- Select Correct Car Model and Year: From the list, select 'Mazda' and then the specific model and year range for your Mazda RX8 (2001-2011).
- Save and Reboot: Save your selections and reboot the Android head unit for changes to take effect.
Image: Screenshots demonstrating how to navigate through Android head unit settings to configure CAN Bus, including entering factory settings and password.
Image: Screenshots showing the selection of CAN Bus Box manufacturer ('Raise') and specific Mazda RX8 car model and year within the Android head unit settings.
Video Demonstration
Watch this video for a visual guide on the product and its features.
Video: A brief overview of the Pinmany RZ-MZD61 CAN Bus Decoder.
Maintenance
The Pinmany RZ-MZD61 CAN Bus Decoder is designed for durability and requires minimal maintenance. Keep the device free from moisture and extreme temperatures. Avoid physical impact. No user-serviceable parts are inside. Do not attempt to open or repair the unit, as this may void any applicable support.
Troubleshooting
- No Functionality After Installation: Double-check all wiring connections against the pin definition diagram. Ensure the operating voltage is correct. Verify that the CAN Bus settings on your Android head unit are correctly configured for 'Raise' manufacturer and your specific Mazda RX8 model.
- Incorrect Functionality: If certain functions (e.g., steering wheel controls) are not working as expected, re-verify the CAN Bus settings on the Android head unit. Consult your head unit vendor for specific configuration details if the issue persists.
- Device Damage: Improper wiring or incorrect voltage can cause damage. If you suspect damage, discontinue use and contact support.
- Unsure About Fitting/Wiring: If you are uncertain about any aspect of the installation or wiring, it is strongly recommended to seek professional assistance or contact the seller for support before proceeding.
Specifications
| Feature | Detail |
|---|---|
| Model Name | RZ-MZD61 |
| Item Type | CAN Bus Data Converter (Cables, Adapters & Sockets) |
| Brand Name | pinmany |
| Manufacturer | Raise |
| Suitable Car Models | Mazda RX8 2001-2011 |
| Suitable Head Unit | Android 7'/9'/10'/etc (7, 8, 9, 10 inch Android Head units) |
| Voltage | 12 V (Operating range: +9V~+16V) |
| Material | Black plastic shell |
| Item Size | 73.5mm * 46.5mm * 18.5mm (approximate, manual measurement error ±1mm) |
| Item Weight | 50g |
| Interface | 16-pin/20-pin PH2.0 connectors |
| PCB Included | Yes |
| High-concerned chemical | None |
| Origin | Mainland China |
Image: Product information detailing model, name, brand, manufacturer, size, interface, weight, and suitable vehicle models.
Image: Diagram showing the dimensions of the CAN Bus Decoder (73.5mm x 46.5mm x 18.5mm).
User Tips
- Always ensure the Android head unit is powered off before connecting or disconnecting the CAN Bus decoder to prevent electrical damage.
- If you encounter difficulty finding the correct factory password for your Android head unit, check the head unit's own manual or contact its manufacturer/seller.
- For optimal performance, ensure all connections are secure and free from corrosion.
Support
For any questions or assistance regarding the Pinmany RZ-MZD61 CAN Bus Decoder, please contact the seller or manufacturer directly. Provide your product model (RZ-MZD61) and a detailed description of your issue for efficient support.