BAOFENG UV5R Mini

Contents

Baofeng UV5R Mini Walkie Talkie User Manual

Model: UV5R Mini | Brand: BAOFENG

1. Introduction and Preface

Thank you for purchasing the Baofeng UV5R Mini Walkie Talkie. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to ensure you derive maximum performance from your radio.

Important Note on Licensing:

WARNING! European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. At this subject, refer to the “EU” specification guide 2014/53/EU.

ATTENTION! When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.

2. Safety Warnings and Regulations

EU Regulatory Conformance

As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.

FCC Part 15/IC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

FCC RF Exposure

WARNING! It is up to the user to properly operate this radio transmitter to ensure safe operation. Please adhere to the following:

  • Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result.
  • Please contact your local dealer for a replacement antenna.

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements.

Body-Worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third-party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

Precautions for Portable Terminals

Operating Prohibitions

To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:

  1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips

To help you make better use of the product, be sure to observe the following instructions:

  1. Do not use any unauthorized or damaged accessory.
  2. Keep the product at least 2.5 centimeters away from your body during transmission.
  3. Do not keep the product receiving at high volume for a long time.
  4. For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
  5. Keep the product and its accessories out of reach of children and pets.
  6. Please operate the product within the specified temperature range.
  7. Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
  8. Handle the product with care.
  9. Do not disassemble, modify or repair the product and its accessories without authorization.

Precautions for Batteries

Charging Prohibitions

To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
  2. Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
  3. Do not charge your battery suffering deformation, leakage and overheat.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge shall always be prohibited for it may shorten the life of your battery.

Maintenance Instructions

To help your battery work normally or prolong its life, be sure to observe the following instructions:

  1. Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
  2. It is recommended to charge the battery under 5°C~40°C. Violation of the said limit may cause battery life reduction or even battery leakage.
  3. To charge a battery attached to the product, turn it off to ensure a full charge.
  4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
  7. Do not squeeze and penetrate the battery, nor remove its housing.

Transportation Instructions

  1. Damaged batteries must not be transported.
  2. To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  3. The radio must be switched off and secured against switch-on, if the battery is attached.

The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.

3. Product Overview and Items in the Package

The Baofeng UV5R Mini is a compact and powerful dual-band radio. Below is an overview of the product and its components.

Two Baofeng UV5R Mini walkie-talkies with key features like Bluetooth Programming, Multi-Bands, Adjustable Power, 999 Channels, and Mini Case.
Figure 3.1: Baofeng UV5R Mini Walkie Talkie - Main Features
Diagram of the Baofeng UV5R Mini with numbered parts including Antenna, SK1, PTT-A, OK/Menu, V/M-VFO/MR, PTT-B, Numeric Keypad, Flashlight, Volume/Power Knob, Screen, Accessory Port, Cancel/Back, Up/Down, A/B, Microphone, LED Indicator, Battery Latch, Type-C Charging indicator, Type-C Charging Port, Search/Flashlight button.
Figure 3.2: Product Overview with Labeled Components

Items in the Package

The standard package includes the following items:

ItemQuantity (PCS)ItemQuantity (PCS)
Radio1Lanyard1
Battery1Operation Manual1
Antenna1Belt Clip1

*Charger and power adapter are subject to the final configuration of the dealer. Please understand that the charging instructions in this manual may not be appropriate if Type-C charging method.

Contents of the Baofeng UV5R Mini package including the radio, user manual, lanyard, clip, antenna, battery, and Type-C charging cables.
Figure 3.3: Package Contents

Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.

CAUTION: Do not hold the radio antenna in your hand, as this will reduce the performance of the radio and the life of the antenna. Do not shake the radio with the top of the antenna in your hand, as this will degrade the performance and life of the radio antenna.

4. Functional Features

The Baofeng UV5R Mini Walkie Talkie offers a wide array of features for versatile communication:

  • Multi-Band Operation: 6-band scan receiver (FM78-108MHz, AM108-136MHz, VHF136-174MHz, UHF400-520MHz, 350-390MHz). Transmit frequency on VHF144-148MHz and UHF420-450MHz.
  • Power Output: 5W/2W RF output with dual PTT transmitter.
  • Programming: Wireless read/write frequency and Bluetooth APP programming for easy frequency settings.
  • Display: 1.44" TFT large screen for clear dual-frequency, dual-band, and dual-display. The display area has increased by 48% compared to classic models.
  • Channel Management: Full keyboard manual frequency input, 999 channel memory, local channel storage and deletion.
  • Frequency Pairing: One-click frequency pairing for easy grouping.
  • Relay Functions: Settings for frequency difference, frequency difference direction, and relay activation audio.
  • Security Features: Alarm function (three types of alarm settings) to protect your security.
  • Customization: Built-in input method supporting local editing of channel names, receiving frequency, and transmitting frequency. Side button function customization for radio, scan, sweep, voice control, flashlight, and alarm.
  • DTMF: DTMF encoding and decoding function, 20 DTMF calls.
  • Other Functions: Frequency hopping, FM radio function (receive frequency 65~108MHz), automatic or manual keypad lock, backlight selection.
  • Charging: Support Type-C charging for strong compatibility and convenience.
Diagram showing multi-band transmit and receive capabilities, including UHF, VHF, AM, and FM frequencies.
Figure 4.1: Multi-Bands Transmit and Receive
Image showing the walkie-talkie and a smartphone screen, illustrating Bluetooth read/write frequency programming via an app.
Figure 4.2: Bluetooth Read/Write Frequency Programming
Two walkie-talkies demonstrating one-touch frequency pairing for easy group matching.
Figure 4.3: One-Touch Frequency Pairing
Close-up of the walkie-talkie showing the dual PTT keys (A and B) for main/secondary channel transmission.
Figure 4.4: Double PTT Keys Design
Close-up of the walkie-talkie's 1.44-inch TFT large screen, highlighting its clear dual-frequency display.
Figure 4.5: 1.44" TFT Large Screen
Image showing two Type-C charging cables, emphasizing the convenience of Type-C charging for the walkie-talkie.
Figure 4.6: Type-C Charging

5. Basic Operations

Turning your Radio On and Off

To turn your radio ON, turn the [Volume/Power] rotary knob clockwise. To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.

Setting the Volume

Increase volume by turning the [Volume/Power] rotary knob clockwise. To decrease volume, turn the [Volume/Power] rotary knob counterclockwise. Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

Locking or Unlocking Keypad

To avoid accidentally changing radio settings:

  1. Press and hold the [*] key to lock the keypad until the screen displays the """ icon.
  2. In lock mode, you can turn the intercom on and off, adjust the volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
  3. In lock mode, press and hold the [*] key to unlock the keypad until the """ icon is no longer displayed to unlock the radio.

Keypad Entry

You can enter radio aliases, channel aliases, numbers, etc. using the radio's numeric keypad.

  1. To switch between input methods, press [# ↑ ] key.
  2. Press 1 to enter a special character (except in numeric input mode, where the number 1 is entered).
  3. Press 0 to enter a space (except in the numeric input mode, in which special characters are entered).

Select a Channel

The channel is the channel through which the signal is transmitted. Press the [V/M] button to toggle between VFO and channel mode to select channel mode. Press the ▲/▼ buttons or the rotary encoder to select the desired channel. Enter the channel number using the keypad. For example, to switch to channel 64, enter 064 totaling 3 digits to switch to channel 64.

Channel Memory

In Frequency and in Standby mode, you can store frequencies and parameters. Press [MENU] [3] [MENU] [1] [5], the screen will display “MEMCH”. Press [MENU] to enter the function. Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm that the storing succeeded. Press [EXIT] to exit to return to standby mode.

NOTES: If you want to set CTCSS tones, DCS codes or the frequency offset, you have to do it before storing the channel. Stored channels are displayed as CH-, other channels have no CH- display.

Delete a channel (DEL-CH)

In VFO mode and in standby mode, press [MENU] [3] [MENU] [1] [6], the screen will display “DELCH”. Press [MENU] to enter the function. Press the ▲/▼ buttons or rotate the encoder to select the channel you want to delete, then press [MENU] to confirm. To return to the standby mode press [EXIT] key. NOTE: Channel 1 cannot be deleted.

Main Band/Sub Band Switch

In standby mode, press the [A/B] key to toggle between the A and B bands to switch between the main/sub bands. The main band is the highlighted band. The darker displayed band is the sub-band.

VFO/Channel Switch

Press the [V/M] button to switch between VFO and channel display. VFO mode will display the ‘VFO' icon. MR mode will display the channel serial number.

Setting the VFO Frequency

Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.

  1. Input the VFO frequency directly with the keypad.
  2. Press the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.

Call Service

All radios in the group must be set to the same channel and sub-code to communicate. To ensure optimal reception volume, keep the distance between the microphone and your mouth at 2.5 cm to 5 cm when transmitting.

  • Initiate a call: Select a channel, press and hold the [PTT-A] key, the radio transmits on segment A (upper screen) and the red indicator light is always on. Then speak into the microphone with normal voice tone. Press and hold the [PTT-B] key, the radio transmits on the B segment (lower screen), and the red indicator light is always on. Then speak into the microphone in a normal voice tone.
  • Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light is always on.

Emergency Alarm

Emergency alarm means that the terminal can initiate an emergency alarm to seek help from the companion or the control center when it encounters an emergency. In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.

Flashlight

In standby mode, press the preset " key to turn the flashlight on or off.

FM Radio Function

Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1. Turn on the radio and press the SK1 key [FM Radio] to enter radio mode and the screen displays the tuning frequency. The following operations can be performed:

  • Press ▲/▼ key to search for radio channels at the preset step frequency.
  • Press the [# ↑ ] key to search for radio channels automatically, the screen displays 'SEEK...'
  • Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
  • Press SK1 key [FM Radio] to exit radio mode.

Monitor

Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. You can also listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. Release the [Monitor] key to exit the monitor mode.

Press the pre-programmed [SEARCH] key or press and hold " key, the radio enters into frequency search state, the screen displays "SEARCH...". Press [# ↑ ] key to switch the searching band, such as VHF/UHF, etc. The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.

Reverse Frequency Function

Short press the [*] key in relay mode can invert the receive frequency and transmit frequency, the screen shows 'R' icon. This function is often used in repeater channels, and is effective when there is a frequency difference between the receive frequency and the transmit frequency.

Talk Around Function

In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode, the screen displays between ‘T' icon and 'R' icon. In Talkaround mode, the receive frequency is equal to the transmit frequency.

Repeater Activation Tone

Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.

Voice-activated transmit (VOX)

Enable VOX function, you don't need to press PTT key to transmit, through the voice of normal speech automatically transmit, after the speech stops, it will stop transmitting automatically and wait for receiving. VOX function is enabled:

  1. Standby status, press [MENU][2][MENU][4] to enter Vox Switch;
  2. Press [MENU][2][MENU][5] to enter Vox Level, press ▲/▼ to select VOX level (level 1-9);
  • Open VOX, select VOX level 1 level-9, the smaller the value, the higher the sensitivity, the 'V' icon is displayed at the top of the screen. Default is off.
  • Turn off VOX, select OFF OFF, V icon disappears.
  1. Press [MENU] key to save the setting and return to the upper menu.
  • Repeat the above operation and select OFF to turn off the VOX function.

Dual Watch

When in Dual watch mode, the radio can receive the frequency set for channel A or B. Operation is as follows:

  1. Press [MENU] [2] to enter Radio Set.
  2. Press [MENU] + ▲ to select "15 Dual Watch".
  3. Press [MENU] key to enter Dual Watch Setting, press ▲/▼ key to select “On”.
  4. Press [MENU] key to save and return to the upper menu. The dual watch function will be turned on, and the icon 'D' will be displayed on the first line of the screen.
  • Repeat the above operation and select "Off”, the Dual Watch function is turned off and the icon 'D' disappears from the first line of the screen. The sub-band displays the " icon.

Stopwatch Function

Press and hold the [MENU] key to enable the stopwatch function. The stopwatch timing operates as follows:

  • Press the [MENU] key to start the stopwatch.
  • Press the [MENU] key again to stop the stopwatch.
  • Press the [EXIT] key to exit the stopwatch function.

Weather Radio/Scan Weather Channel

Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.

  1. To turn the NOAA Weather Scan on, press and hold the [0] key for 3 seconds, " icon appears. The radio will go to Weather band mode.
  2. Press and hold the [# ↑ ] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the [# ↑ ] key for 3 seconds during a NOAA weather scan will stop the scan.
  3. After stopping NOAA weather scan, it is allowed to manually select the weather channel by press the ▲ or ▼ key.
  4. To exit the Weather Radio broadcast mode, press the " key or [PTT] key.

Weather Channel Frequencies and Names

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

NOTE: Weather Channels Wx 1 Thru 10, Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

6. Use of Menu Functions

Basic use

Using the menu with arrow keys:

  1. Press the [MENU] button to enter the menu.
  2. Use the ▼/▲ buttons or the encoder to navigate between menu items.
  3. Once you find the desired menu item, press [MENU] again to select that menu item.
  4. Use the ▼/▲ buttons or the encoder to select the desired parameter.
  5. When you've selected the parameter you want to set for a given menu item;
    1. To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
    2. To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
  6. To exit out of the menu at any time, press the [EXIT] button.

Using the menu with short-cuts

  1. Press the [MENU] button to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] button.
  4. For entering the desired parameter you have two options:
    1. Use the arrow buttons as we did in the previous section; or
    2. Use the numerical keypad to enter the numerical short-cut code.
  5. And just as in the previous section;
    1. To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
    2. To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
  6. To exit out of the menu at any time, press the [EXIT] button.

Wireless Program Radio

You can program the radio wirelessly. Before programming the radio wirelessly, you need to install the APP program. Download the app by scanning the QR codes below:

User manual cover showing QR codes for Android and iOS apps to program the radio.
Figure 6.1: Scan QR codes for Android and iOS Apps

The radio operates as follows:

  1. Press [MENU] + [4] to enter Wireless CPS.
  2. Press [MENU] + ▲/▼ to select "On"; The " icon will be displayed on the first line of the screen.

Download radio APP

You can program the terminal through the radio APP. Download and install radio APP on your Android phone. After the APP is opened, allow the Bluetooth of the cell phone and open the location function, select the walkie-talkie model 5Rmini Series, connect the radio, click Walkie-talkie. prompt the connection success and return to the home page.

Programming Steps:

  • Read the radio data: After finishing the frequency reading, click the program to enter the program details. In the program details interface you can program channel information, frequency mode, optional functions.
  • Save Profile: The programmed profile allows you to save the profile as a new profile and name the new profile. If you select Replace Program, click Replace Program and save.
  • Write data to radio: click home page, select program, click 'Write' to enter write frequency, the radio will restart automatically when finish writing frequency.

Shortcut Menu Operations

MenuNameSettingDescription
SCANFreq RangerNNNNnnnInput VFO range lower and upper frequency
Scan ModeTimeTime Operation - scanning will resume after a fixed time has passed
CarrierCarrier Operation - scanning will resume after the signal disappears
SearchSearch Operation - scanning will not resume
Scan MemoryALLRX_TX are saved (default is all, encoding and decoding are the same)
DECODERSave only in Transmitter CTCSS/DCS
ENCODERSave only in Receiver CTCSS/DCS
Radio SettingStep2.5-100KSelects the amount of frequency change in VFO/Frequency mode when scanning or pressing the ▲ or ▼ keys.
SquelchOFF,LEVEL1-LEVEL5Squelch silences the receiver when there is no signal. Setting the squelch to 0 will open up the squelch entirely.
Power SaveOFFTurn off radio sleep. The battery consumption is large, and the standby time may be shortened
ONTurn on radio sleep. Turning on is more power efficient, but you might miss the first few syllables before the RX turns on.
VOX SwitchOFFTurn off the radio VOX.
ONTurn on the radio VOX.
VOX LevelLEVEL1-LEVEL9When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the gain level to an appropriate sensitivity to allow smooth transmission.
VOX Delay0.5......2.0sWhen the VOX is enabled, set up the VOX delay to help to extend the transmission time to avoid stopping a transmission too early. 0.5s-2s, Step 0.1 second. a total of 16 times offered.
TOTOFFAllow continuous launch, launch time is not limited
15;30;45...180Maximum allowed time for transmission while holding down the PTT key.
TOAOFFDisable TOA function
1......10Activate TOA function. Range 0 – 10 seconds, Step 1 second.
VoiceOFFDisable voice prompts
ONActivate voice prompts
LanguageChineseDisplay menus and voice prompts in Chinese language
EnglishDisplay menus and voice prompts in English language
ROGEROFFDisable ROGER function. Release PTT key without ROGER audio.
BEEPActivate the ROGER function. Sends an end-of-transmission tone to indicate to other stations that the transmission has ended.
TONE 1200Activates the ROGER function. Sends the DMC1200 transmission end tone to indicate to other stations that the transmission has ended.
OFFDisable key confirmation tone.
BeepONActivation key to confirm tone. Allows audible confirmation of a key press
ALWAYS ONThe backlight is always on.
BackLight5......20Set the backlight off time in no-operation delay time. 5-20, step value is 5.
PICTUREShow preset picture when radio is on
Dual WatchOFFDisable dual table, dual receive.
ONMonitor [A] and [B] at the same time. The display with the most recent activity ([A] or [B]) becomes the selected display.
AutoLockOFFDisable automatic keypad lock. Allow manual keypad lock (press and hold the " key to lock/unlock the keyboard)
ONWhen ON, the keypad will be locked if not used in 8 seconds. Pressing the " key for 2 seconds will unlock the keypad.
Alarm ModeOn SiteSounds alarm through your radio speaker only
Send SoundTransmits a cycling tone over-the-air
Send CodeTransmits '119' (911 in reverse) followed by the ANI code over-the-air
Alarm ToneOFFThe radio speaker blocks the alarm sound.
ONThe radio speaker sounds an alarm
ANI-Edit100View the ANI ID, and if necessary, will allow to change the ANI ID
Display ANIOFFDisable the ANI code display function
ONEnable ANI code display
DTMF-STOFFNo DTMF Side Tones are heard
DT-STSide Tones are heard only from manually keyed DTMF codes
ANI-STSide Tones are heard only from automatically keyed DTMF codes
DT+ANIAll DTMF Side Tones are heard
PTT-IDOFFNo ID is sent.
BOTThe selected S-CODE is sent at the beginning
EOTThe selected S-CODE is sent at the ending
BOTHThe selected S-CODE is sent at the beginning and ending
Program ChannelCH.NAMEChannel 1View channel name, allows to rename the current channel. Press the #z key to switch the input method, allowing the input of letters, numbers and symbols.
RX FrequencyView the current channel Receiver frequency.
TX FrequencyView the current channel Transmitter frequency.
Trans PowerHighSelects between HIGH transmitter power when in VFO/Frequency mode.
LowSelects between LOW transmitter power when in VFO/Frequency mode.
BandwidthWideWideband (25 kHz bandwidth)
Narrownarrowband (12.5 kHz bandwidth)
RX CTCSSOFF;67-254.1Mutes the speaker of the transceiver in the absence of a specific and continuous sub-audible signal. If the station you are listening to does not transmit this specific and continuous signal, you will not hear anything.
OFF;023N-7541Mutes the speaker of the transceiver in the absence of a specific low-level digital signal. If the station you are listening to does not transmit this specific signal, you will not hear anything.
TX CTCSSOFF;67-254Transmits a specific and continuous sub audible signal to unlock the squelch of a distant receiver (usually a repeater).
OFF;023N-7541Transmits a specific low-level digital signal to unlock the squelch of a distant receiver (usually a repeater).
EncryptionOFFDisable encrypted mode, your conversations are not private.
ONActivating encryption mode ensures the privacy of your conversations. To use the Encryption function, the other part of the radio must also have Encryption activated and must be tuned on the same DCS code.
Signaling1-20Selects 1 of 20 DTMF codes. The DTMF codes are programmed with software and are up to 3 digits each.
CH-MDFNAMEMR/Channel mode is displayed in NAME format. Note: NAME allows CPS program or edit in the channel name (Munu 1)
FREQMR/Channel mode is displayed in frequency format.
CHMR/Channel mode is displayed in CH format.
SP-MuteQTwhen radios is set in this mode, the monitor feature is activated only when the radio receives the correct CTCSS/DCS.
QT+DTMFwith this option, the monitor is activated when the radio receives the correct CTCSS/DCS and the correct DTMF code.
Wireless CPSOFFTurn off Wireless CPS and disable the Wireless programming function
ONEnable Wireless CPS to program the radio via Wireless
Radio InfoRadio ID\Firmware\HardwareDisplays radio ID, firmware version, hardware version. to check the radio information.

7. Technical Specifications

Below are the technical specifications for the Baofeng UV5R Mini Walkie Talkie:

CategorySpecification
Receiver FrequencyFM 76-108 MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz
Transmission FrequencyVHF 144-148MHz, UHF 420-450MHz
Channel Spacing25.0KHz(Wide)/12.5KHz(Narr)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Dimensions108mm×52mm×37mm (No antenna)
Weight200g (Battery pack included)
Transmission current≤1600mA
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm

NOTE: All specifications may be modified without prior notice or liability.

Technical Specification diagram showing the dimensions of the Baofeng UV5R Mini: 107mm height (without antenna), 52mm width, and 37mm depth.
Figure 7.1: Technical Specification - Dimensions

8. Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.

  • Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
  • Do not store the Radio under the sunshine or in hot areas.
  • High temperatures can shorten the life of electronic devices, and warp or melt certain plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
  • If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio.
  • Do not transmit without antenna.

9. Disclaimer and Support

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.

For the full user manual in PDF format, please refer to the official document available at: Baofeng UV5R Mini User Manual (PDF)

User manual cover with QR codes for Android and iOS apps.
Figure 9.1: User Manual Cover with App QR Codes

© 2023 BAOFENG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.