HeltecBMS HT-66115LOS03A200, HT-66115LPS04A200

Contents

Heltec BMS 3S/4S 200A Battery Protection Board User Manual

Model: HT-66115LOS03A200, HT-66115LPS04A200

Brand: HeltecBMS

1. Introduction

This manual provides essential information for the safe and effective use of your Heltec BMS 3S or 4S 200A Battery Protection Board. This board is designed for LiFePO4 and Li-ion battery systems, offering balance charging and high current protection for applications such as 12V inverters and energy storage systems.

Please read all instructions carefully before installation and operation to ensure optimal performance and safety.

2. Safety & Warnings

  • Read all instructions before use to ensure safety and prevent damage.
  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Ensure proper polarity and connections as per the wiring diagrams to avoid damage to the BMS or battery pack.
  • Do not connect or disconnect ports while welding or under load.
  • Always double-check all wiring connections before applying power.
  • This device is intended for use by individuals with sufficient technical knowledge of battery systems and electronics.

3. Product Overview

The Heltec BMS is a robust battery management system available in 3S (3-series) and 4S (4-series) configurations, both rated for 200A continuous current. It provides essential protection and balancing functions for your battery pack.

Heltec BMS 3S/4S Battery Protection Board

Figure 1: Heltec BMS 3S and 4S Battery Protection Boards

Product Components:

List of product components for Heltec BMS

Figure 2: Included components for 3S/4S BMS

  • BMS Board (1x)
  • Collection Line (2x)
  • Screws (4x)
  • Nuts (4x)

Product Dimensions:

Dimensions of the Heltec BMS board

Figure 3: Heltec BMS Product Size (115mm x 66mm x 9mm)

The dimensions for both 3S and 4S models are approximately 163mm x 82mm x 12mm (6.42in x 3.23in x 0.47in). Please refer to the diagram for detailed measurements.

Product Video:

Video 1: Unboxing and visual overview of the Heltec BMS board.

4. Specifications

General Specifications:

Attribute Value
Brand NameHeltecBMS
TypeLI-ION Battery BMS
Handware or SmartHandware BMS
Balance FunctionPassive Balanced BMS
Charge and Discharge PortCommon Port BMS
Charging Current200A
Usage ScenarioPower BMS, Energy Storage BMS
FunctionOvercharge Protection, Over Discharge Protection, Overcurrent Protection
High-concerned chemicalnone
CertificationCE
OriginMainland China
Package Dimensions (L x W x H)11cm x 12cm x 2cm
Package Weight0.16 kg

3S 200A 3.7V Same Port Specifics:

Attribute Value
ConnectionSame Port
Size163×82×12mm
Overcharge protection4.25V ± 0.25V
Charging recovery4.2V ± 0.25V
Over-discharge protection2.8V ± 0.25V
Discharge recovery3.0V ± 0.25V
Max continuous current200A
Max Charge Current600A
Peak Current1000A
Balance current200 mA
Balanced starting voltage4.21V ± 0.25V
Self-consumption≤35uA

4S 200A 3.2V Same Port Specifics:

Attribute Value
ConnectionSame Port
Size163*82*12MM
Charge protection voltage3.65V
Charge release voltage3.55V
Discharge protection voltage2.35V
Discharge release voltage2.55V
Balanced voltage3.405V
Balanced current200MA
Maximum continuous overcurrent200A
Peak Current600A

5. Setup and Connection

Important: When welding, do not connect the ports. Verify the battery series sequence, wire according to the drawing, and double-check all connections before applying power.

Connect the black wire to B-, and then connect the positive terminal of the battery from right to left in sequence.

5.1. 3S Connection Diagram

Wiring diagram for 3S BMS

Figure 4: 3S 200A 3.7V BMS Connection Diagram

Follow the diagram above for connecting a 3-series battery pack to the 3S BMS. Ensure the balance wires are connected in the correct order from the first string to the last string, and the main power connections (Pack+, Pack-, P-) are secure.

5.2. 4S Connection Diagram

Wiring diagram for 4S BMS

Figure 5: 4S 200A 3.2V BMS Connection Diagram

Follow the diagram above for connecting a 4-series battery pack to the 4S BMS. Pay close attention to the balance wire sequence and main power connections (Pack+, Pack-, P-) to ensure correct operation.

6. Operating Instructions

Once properly installed and connected, the Heltec BMS will automatically manage your battery pack's charging and discharging cycles, as well as cell balancing. It provides protection against common issues such as overcharge, over-discharge, and overcurrent.

  • Charging: Connect your charger to the designated charge input. The BMS will ensure cells are charged safely and balanced.
  • Discharging: Connect your load (e.g., inverter) to the discharge output. The BMS will protect against overcurrent and over-discharge.
  • Balancing: The passive balancing function will automatically activate to equalize cell voltages when necessary, typically during charging.

7. Maintenance

  • Regularly inspect all wiring connections for tightness and corrosion.
  • Keep the BMS clean and free from dust and moisture.
  • Ensure adequate ventilation around the BMS, especially during high current operation, to prevent overheating.
  • Avoid exposing the BMS to extreme temperatures or direct sunlight.

8. Troubleshooting

  • BMS not functioning: Check all wiring connections, especially the balance leads and main power connections. Ensure the battery pack voltage is within the operational range.
  • Battery not charging/discharging: Verify that the charger/load is correctly connected and functioning. Check for any tripped protection (e.g., overcurrent, over-discharge) which might require disconnecting the load/charger and allowing the BMS to reset.
  • Cell voltage imbalance: The passive balancing feature works over time. If a significant imbalance persists, check individual cell voltages and balance wire connections.

9. User Tips

  • Always use appropriate gauge wires for high current applications to prevent overheating and voltage drop.
  • Consider adding an external fuse on the main positive line for additional safety.
  • For long-term storage, ensure the battery pack is at a recommended storage voltage, and disconnect the BMS if self-consumption is a concern for very long periods.

10. Manufacturer & Support Information

Manufacturer: chengdu heltec energy Technology Co., Ltd

Address: No.16th Chenghong Rd., Chengdu, SiChuan, China.

Email: echo@heltec-bms.com

EU Authorized Representative: eVatmaster Consulting GmbH

EU Representative Address: Bettinastr. 30, 60325 Frankfurt am Main, Germany

EU Representative Tel: 0049-6995179070

EU Representative Email: contact@evatmaster.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.