JASIC WSME-200 (E201II)

Contents

JASIC WSME-200 (E201II) Pulse AC/DC TIG Welder User Manual

Model: WSME-200 (E201II)

1. Safety Precautions

Always prioritize safety when operating welding equipment. Failure to follow safety guidelines can result in serious injury or death. Read and understand all safety warnings before use.

  • Wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
  • Ensure adequate ventilation to avoid inhaling welding fumes.
  • Keep a fire extinguisher nearby and know how to use it.
  • Do not operate the welder in damp or wet conditions.
  • Ensure the work area is clear of flammable materials.
  • Always disconnect power before performing maintenance or adjustments.
  • Never touch live electrical parts.

2. Product Overview

The JASIC WSME-200 (E201II) is a versatile Pulse AC/DC TIG welding machine designed for precision welding of various metals, including aluminum, stainless steel, and carbon steel. It features advanced control options for both AC and DC TIG welding, including pulse functionality.

Front view of the JASIC WSME-200 TIG Welder, showing the control panel and front connectors.
Figure 2.1: Front view of the JASIC WSME-200 TIG Welder, showing the control panel and front connectors.
JASIC WSME-200 TIG Welder with included accessories: welding torch, ground clamp, and user manual.
Figure 2.2: JASIC WSME-200 TIG Welder with included accessories: welding torch, ground clamp, and user manual.

3. Setup Instructions

3.1 Unpacking and Inspection

  1. Carefully remove the welding machine and all accessories from the packaging.
  2. Inspect the machine for any signs of damage during transit. If damaged, contact your supplier immediately.
  3. Ensure all components listed in the packing list are present.

3.2 Power Connection

The WSME-200 (E201II) operates on a 1~220V AC power supply.

  1. Locate the power input on the rear panel of the welder.
  2. Connect the power cable to a suitable 1~220V AC power outlet with appropriate circuit protection.
  3. Ensure the power switch on the rear panel is in the 'OFF' position before connecting to power.
Rear view of the JASIC WSME-200 TIG Welder, showing the power input (AC 1~220V), main power switch, and gas inlet.
Figure 3.1: Rear panel connections including power input and gas inlet.

3.3 Gas Connection

For TIG welding, an inert shielding gas (typically Argon) is required.

  1. Connect the gas hose from your Argon cylinder regulator to the gas inlet connector on the rear panel of the welder.
  2. Ensure all connections are tight to prevent gas leaks.
  3. Set the gas flow rate at the regulator according to your welding requirements (typically 10-15 L/min for TIG).

3.4 Welding Torch and Ground Clamp Connection

Connect the welding torch and ground clamp to the front panel of the machine.

  1. Connect the TIG torch cable to the appropriate connector on the front panel.
  2. Connect the ground clamp cable to the designated ground terminal.
  3. Ensure both connections are secure.
Close-up of the control panel of the JASIC WSME-200, detailing various settings and the current display.
Figure 3.2: Close-up of the control panel and front connectors for torch and ground.

4. Operating Instructions

4.1 Powering On/Off

  1. After all connections are made, turn the main power switch on the rear panel to the 'ON' position.
  2. The digital display on the front panel should illuminate.
  3. To power off, turn the main power switch to the 'OFF' position.

4.2 Control Panel Overview

The control panel allows selection of welding modes and adjustment of parameters.

Close-up of the control panel of the JASIC WSME-200, detailing various settings and the current display.
Figure 4.1: Detailed view of the control panel.

Key controls typically include:

  • Mode Selection: Buttons for AC TIG, DC TIG, Pulse TIG.
  • Current Adjustment: A large rotary knob to set the welding current (Amperage). The digital display shows the current value.
  • Pulse Settings: For Pulse TIG, controls for pulse frequency, peak current, base current, and pulse width.
  • Gas Pre/Post Flow: Adjustments for shielding gas flow before and after the arc.
  • 2T/4T Trigger Mode: Selection for torch trigger operation.

4.3 Setting Welding Parameters

  1. Select Welding Mode: Choose AC TIG for aluminum, DC TIG for stainless steel, carbon steel, etc.
  2. Adjust Current: Rotate the main current knob to set the desired amperage for your material thickness and joint type.
  3. Set Gas Flow: Ensure the gas regulator is set to the appropriate flow rate.
  4. Pulse Settings (if applicable): For pulse welding, adjust pulse frequency, peak/base current, and pulse width as needed for improved control and reduced heat input.
  5. Test Weld: Always perform a test weld on scrap material to verify settings before welding your actual workpiece.

5. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your welding machine.

5.1 Daily Maintenance

  • Clean the welding torch nozzle and collet body.
  • Inspect the tungsten electrode for wear or contamination and regrind or replace as necessary.
  • Check all cables and connections for damage or looseness.
  • Wipe down the machine exterior to remove dust and debris.

5.2 Periodic Maintenance

  • Internal Cleaning: Periodically open the machine (ensure power is disconnected) and use compressed air to blow out dust from internal components and cooling fins.
  • Gas Line Inspection: Check gas hoses and connections for leaks or damage.
  • Ground Clamp: Ensure the ground clamp is clean and makes good electrical contact.

Warning: Only qualified personnel should perform internal maintenance. Disconnect power before opening the machine.

6. Troubleshooting

This section addresses common issues you might encounter.

6.1 No Arc / Weak Arc

  • Check Power: Ensure the machine is powered on and receiving adequate input voltage (1~220V).
  • Check Ground Connection: Verify the ground clamp is securely attached to the workpiece and making good electrical contact.
  • Check Torch Connections: Ensure the TIG torch is properly connected to the machine.
  • Tungsten Electrode: Check if the tungsten is properly installed, sharpened, and not contaminated.
  • Current Setting: Increase the welding current if it's too low for the material.

6.2 Poor Weld Quality

  • Shielding Gas: Check gas flow rate, ensure the gas cylinder is not empty, and there are no leaks in the gas line. Contaminated gas can also cause issues.
  • Tungsten Contamination: Ensure the tungsten electrode is clean and properly sharpened.
  • Material Cleanliness: The workpiece must be clean and free of oil, rust, or paint.
  • Travel Speed/Arc Length: Adjust your travel speed and maintain a consistent arc length.
  • Filler Rod: Ensure you are using the correct type and size of filler rod for the material.

6.3 Overheating Indication

  • Duty Cycle: The machine may have exceeded its duty cycle. Allow it to cool down.
  • Ventilation: Ensure the machine's ventilation grilles are not blocked and there is sufficient airflow around the unit.
  • Ambient Temperature: Operating in excessively hot environments can lead to overheating.

7. Specifications

FeatureSpecification
ModelWSME-200 (E201II)
Welding TypePulse AC/DC TIG Welder
Input Voltage1~220V AC
Max Welding Current200A (inferred from model name)
Approx. Unit Weight10.0 kg (based on package weight)
Approx. Unit Dimensions (L x W x H)48cm x 48cm x 48cm (based on package dimensions)

Note: Specifications are subject to change without notice. Refer to the product label for the most accurate information.

8. User Tips

  • Tungsten Selection: Use pure tungsten (green tip) for AC welding of aluminum and thoriated (red tip) or lanthanated (gold/blue tip) for DC welding of steel and stainless steel.
  • Arc Length: Maintain a short and consistent arc length for better control and penetration.
  • Filler Rod Angle: Keep the filler rod at a low angle to the workpiece, feeding it smoothly into the weld puddle.
  • Cleanliness is Key: Always ensure your workpiece, tungsten, and filler rod are meticulously clean to prevent contamination and achieve high-quality welds.
  • Practice: TIG welding requires practice. Start with simple joints on scrap material to develop your technique.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt and product serial number handy when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.