YTYIN LW-184-12-20-H

Contents

12L Aluminum Diving Scuba Gas Tank Instruction Manual

Model: LW-184-12-20-H | Brand: YTYIN

1. Introduction

This manual provides essential information for the safe and effective use, maintenance, and storage of your YTYIN 12L Aluminum Diving Scuba Gas Tank. Please read this manual thoroughly before using the equipment. Proper understanding and adherence to these instructions are crucial for your safety and the longevity of the product.

Video: Overview of Snow Rain Scuba Cylinders, highlighting safety, durability, and convenience.

2. Specifications

The YTYIN 12L Aluminum Diving Scuba Gas Tank is designed for reliable performance in underwater environments. Key specifications are detailed below:

FeatureDetail
Manufacture StandardISO7866, GB11640, EN1975, DOT3AL
MaterialAluminum 6061
CertificateCE and DOT
Filling ContentCompressed air for scuba diving
Surface FinishPainting, polish, and sand blast
Thread3/4-14NPSM, G3/4 or as per requirement
Recommended ValveDIN/Yoke/DIN-Yoke
Capacity12L (Water capacity)
Working Pressure200bar
Model (Example)LW-185-12-20-H (185mm OD, 705mm Length, 15.2kg Weight)
Detailed view of a scuba tank with markings and valve, showing dedicated stapling, valve availability, and thread type.

Image: Detailed view of cylinder markings and valve, indicating 'Dedicate stapling', 'Valve available', 'Dedicate thread', and 'Cylinder thread: 3/4-14NPSM or customized'.

Two types of scuba tank valves, DIN and Yoke, for connecting regulators.

Image: Two common types of scuba tank valves: DIN and Yoke, compatible with various regulators.

3. Setup

  1. Visual Inspection: Before each use, visually inspect the tank for any signs of damage, corrosion, dents, or deep scratches. Check the valve for any obstructions or damage.
  2. Valve Attachment (if separate): If the valve is not pre-attached, ensure the threads on both the tank and the valve are clean and free of debris. Apply a suitable thread sealant if recommended by the valve manufacturer. Hand-tighten the valve, then use a specialized wrench to tighten it to the manufacturer's specified torque.
  3. Filling: Scuba tanks must only be filled by certified technicians at authorized filling stations. Ensure the tank is within its hydrostatic test date. Never overfill the tank beyond its rated working pressure (200 bar for this model).
  4. Regulator Attachment: Ensure the regulator's O-ring is in good condition and properly seated. Attach the regulator to the tank valve, ensuring a snug fit. For Yoke valves, align the regulator and tighten the screw clamp. For DIN valves, screw the regulator directly into the valve.
  5. Pressure Check: Slowly open the tank valve while observing the regulator's pressure gauge. Listen for any leaks. If a leak is detected, close the valve and re-seat the regulator.

4. Operating Guidelines

Always follow safe diving practices and local regulations. This tank is designed to hold compressed air for breathing underwater.

  • Pre-Dive Checks: Verify tank pressure, check for leaks, and ensure all equipment is functioning correctly before entering the water.
  • Breathing: Breathe normally and continuously from your regulator. Never hold your breath while ascending.
  • Air Management: Constantly monitor your air supply using your submersible pressure gauge. Plan your dive to ensure you have sufficient air for the entire dive, including ascent and safety stops.
  • Ascent: Ascend slowly, following your dive computer or tables, and perform a safety stop as required.
  • Post-Dive: After the dive, close the tank valve, then purge the regulator by pressing the purge button to release residual pressure.

5. Maintenance

Regular maintenance is crucial for the safety and longevity of your scuba tank.

  • Rinsing: After each use, thoroughly rinse the tank and valve with fresh water to remove salt, sand, and other contaminants. Pay special attention to the valve area.
  • Drying: Allow the tank and valve to air dry completely before storage. Avoid direct sunlight for prolonged periods.
  • Visual Inspections (VIP): Your tank requires an annual visual inspection by a certified technician. This checks for internal and external corrosion, cracks, and other damage.
  • Hydrostatic Testing: Scuba tanks must undergo hydrostatic testing every 5 years (or as required by local regulations) to ensure their structural integrity. The test date is stamped on the tank.
  • Storage: Store the tank in a cool, dry place, away from direct sunlight and extreme temperatures. Keep the valve slightly open to prevent moisture from being trapped inside, but ensure it's not fully open to prevent contaminants from entering. Store with a minimum of 200-500 PSI to prevent moisture ingress.

6. Troubleshooting

  • Air Leak from Regulator Connection:
            Possible Cause: Damaged or improperly seated O-ring, loose connection.
            Solution: Close tank valve, remove regulator, inspect and replace O-ring if necessary, re-attach regulator securely.
  • Low Pressure Reading:
            Possible Cause: Tank not fully filled, actual leak.
            Solution: Confirm tank was filled to correct pressure. If pressure drops rapidly, check for leaks at all connections. Do not dive with a leaking tank.
  • Difficulty Opening/Closing Valve:
            Possible Cause: Corrosion, debris, or damaged valve mechanism.
            Solution: Do not force the valve. Have it inspected and serviced by a certified technician.
  • Unusual Taste or Smell in Air:
            Possible Cause: Contaminated air fill.
            Solution: Do not use the tank. Return it to the filling station and report the issue. Only use air from reputable, certified sources.

7. User Tips

  • Always transport your scuba tank securely to prevent it from rolling or falling, which could damage the valve or tank.
  • Consider using a tank boot to protect the bottom of your cylinder from abrasion and provide stability when standing upright.
  • When storing for extended periods, ensure the tank is clean, dry, and has some pressure (e.g., 200-500 PSI) to prevent moisture from entering.
  • Familiarize yourself with the markings on your tank, including the hydrostatic test date, working pressure, and material.

8. Warranty & Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Ensure you retain your proof of purchase for any warranty claims. Always refer to certified diving professionals for any questions regarding diving safety or equipment handling beyond the scope of this manual.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.