VDIAGTOOL D100

Contents

VDIAGTOOL D100 OBD2 Scanner User Manual

Vehicle Communication Interface (VCI)

VDIAGTOOL D100 OBD2 Scanner device

1. Safety Information

To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.

When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.

Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.

Safety Messages

Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:

DANGER

Will result in death or serious injury if ignored. Indicates an immediately life-threatening hazard.

WARNING

Could result in death or serious injury if ignored. Indicates a potentially dangerous situation.

Safety Instructions

This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.

DANGER

  • Always ventilate the service area when engine is running or use building exhaust removal system if available.
  • Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.

WARNINGS

  • Always conduct testing in a safe, controlled environment.
  • Wear ANSI-approved safety goggles during all operations.
  • Keep all objects away from moving or hot engine components.
  • Ensure proper ventilation to avoid toxic exhaust fumes.
  • Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with parking brake engaged.
  • Place wheel chocks and never leave the vehicle unattended during tests.
  • Exercise extreme caution around ignition systems - hazardous voltages are present.
  • Maintain an ABC-rated fire extinguisher within immediate reach.
  • Never connect/disconnect test equipment with ignition on or engine running.
  • Keep all test equipment clean, dry and free from contaminants.
  • Never operate test equipment while driving - focus solely on testing.
  • Strictly follow the vehicle service manual's diagnostic procedures.
  • Verify full battery charge and secure DLC connections before testing.
  • Never place test equipment near the distributor due to EMI risks.

2. Product Overview

The VDIAGTOOL D100 is a compact, portable full-system diagnostic tool designed to work seamlessly with both iOS and Android smartphones and tablets. Small enough to fit in your pocket, it offers a comprehensive scan of all vehicle systems and supports FCA. It is an ideal DIY solution for users who want to quickly diagnose their vehicles. The device also provides access to numerous special functions, including Oil Reset, ABS Bleeding, and EPB Reset.

The D100 OBD2 scanner Bluetooth offers professional-grade diagnostics for car owners and DIY enthusiasts. It comes with lifetime free updates and all features available at no extra cost. Supporting 17 reset services, over 4,000 active tests, and full-system diagnostics beyond just engine fault codes. It is an ideal automotive diagnostic tool—compact, portable, with 22 kinds of language, no IP restrictions, and easy to use. It saves your time by eliminating long repair shop queues and allows on-demand diagnostics at home.

Video: VDIAGTOOL D100 Product Overview, demonstrating its compact design, app interface, and key diagnostic capabilities.

3. Getting Started (Setup)

3.1 Download & Install APP

To get started, download the VDIAGTOOL app from the Google Play Store or Apple App Store. You can also visit our official download page: www.vdiagtool.com/support/downloads to get the download link.

3.2 Registration & Activation

To begin using the app, you will need to register an account to bind your VCI device.

  1. Enter your email address and password.
  2. Tap Create Account - a verification code will be sent to your email.
  3. Enter the verification code and tap Next to complete the registration.

Note: If you don't receive the verification email, please check your spam or junk folder.

3.3 Adding a Device

If this is your first time using the device, you will need to add and activate it. You can add the device by either:

  • Scanning the QR code on the device.
  • Manually entering the serial number and activation code.

After scanning the QR code, tap OK to activate. If entering manually, tap Activate to complete the process.

3.4 Connect the Device

After successfully adding your device, the app will prompt you to connect it to begin diagnostics. This device is powered through the vehicle's OBD-II port and operates on 12V power from the vehicle. It will automatically turn on once plugged into a compatible Data Link Connector (DLC).

Connection Steps:

  1. Insert the device firmly into the vehicle's OBD-II port. Ensure it is fully seated and secure.
  2. Start the vehicle's engine.
  3. Enable Bluetooth on your phone, then select and pair the device in your Bluetooth settings. The connection will establish automatically within approximately 15 seconds.

IMPORTANT:

Do not supply power to the device via the Type-C port while it is communicating with the vehicle.

Note: A green VCI indicator in the upper right corner of the app confirms a successful connection. You may then proceed with vehicle diagnostics.

4. Operating Instructions

4.1 Main Menu Overview

Upon launching the app, you will enter the main menu, which includes the following options:

  • Auto Scan: Automatically identifies the vehicle's VIN and performs a comprehensive scan of all available electronic control modules for diagnostics.
  • OBD II: Accesses the OBDII functions menu.
  • Diagnosis: Opens the diagnostic menu, where you can select a vehicle via automatic VIN detection or manual input (make, model, year, and configuration). This section also allows access to the DEMO program and OBDII tests.
  • Special Function: Provides a range of common maintenance services used by both DIY enthusiasts and professionals for everyday auto repair tasks.
  • Updates: Allows internet-based updates of the diagnostic software.
  • Report: View saved diagnostic reports, export them as PDF files, or share via email.
  • Mall: Purchase additional features and functions.
  • Home: Returns to the main menu screen.
  • Application Center: Navigates to the APP center.
  • Me: Manage account settings, configure device preferences, update the system, and adjust other personal settings.

4.2 Diagnose Vehicles

Accurate vehicle identification is required for the diagnostic tool to establish communication and perform diagnostics. The identification process is menu-guided—follow the on-screen prompts to enter the necessary information. Specific steps may vary depending on the vehicle's make, model, and year.

You can identify a vehicle using one of the following four methods:

  • Auto Scan: Tap "Auto Scan” icon on the main menu screen, and the tool will scan the vehicle VIN and decode the VIN for vehicle identification automatically. Note: Auto Scan does NOT work on all vehicles. When Auto Scan fails, try Diagnosis instead.
  • Diagnosis: Tap "Diagnosis” icon on the main menu screen, the tool will bring up vehicle selection menu. Under this menu, you can also tap the Auto Scan to enter the diagnosis menu. Or, you can manually input the vehicle VIN number (17 digits). Note: Some vehicle VINs may not be decodable. When Auto Scan and Manual Input fail, try manual vehicle selection instead.
  • Automatic Detection: Tap Manual Diagnosis, select the region of the vehicle brand (e.g., Americas), choose the brand (e.g., CADILLAC), and then select Automatic Detection to allow the device to automatically identify the connected vehicle. Note: Automatic Detection is not supported on all vehicle models. If this method fails, please try Manual Selection instead.
  • Manual Selection: When the "Auto Scan”, “Manual Input" and "Automatic Detection" fail to identify the vehicle, you can always try “Manual Selection” to identify the vehicle and proceed to diagnosis. Manual Selection is the most reliable vehicle identification option.

4.3 Diagnosis Functions

When you enter the vehicle model diagnostic menu, it will show the following functions:

  • Automatic Scan: It will automatically scan all systems of your vehicle to see if there are any problems.
  • CAN Fast Scan (After 2005): Rapidly scans all accessible vehicle systems for post-2005 vehicles using CAN protocol communication.
  • Full System Diagnosis: Select a specific vehicle control module for diagnostics when you already have an idea which system may be causing issues.

4.4 Diagnostics

After successful vehicle identification, the device can scan and access the vehicle's electronic control systems to Read DTC, read Live Data, Read Freeze Frame, access ECU information, and perform tests such as active tests (bi-directional controls or actuator tests), and more.

  • Read ECU Information: This function is to read ECU version information, which is the equivalent of System Identification or System Information in some electronic control systems, which means to read ECU-related software and hardware versions, models, and production date of the diesel engine, part number, etc.
  • Read DTC: Displays diagnostic trouble code (DTC) records stored in the vehicle's electronic control modules. Selecting this option may open a submenu with additional viewing choices. If the tool displays “System is OK” or “No Trouble Code”, this may indicate: No relevant fault codes are stored in the ECU; The fault is not within that specific ECU's domain (e.g., mechanical or circuit issues); A sensor signal is abnormal but still within its operational range — such cases can be further analyzed using Live Data (PID).
  • Clear DTC: Erases both current and historical DTC records, along with related data, from the vehicle's electronic control modules. After initiating the erase command, the ECU will verify whether the issue has been resolved over several drive cycles.
  • Live Data: Displays Live Data from vehicle sensors and control modules. View data in list or graph formats, set custom value thresholds, and monitor up to 8 sensors simultaneously in list, individual graph, or merged graph views.
  • Read Freeze Frame: When a fault code is triggered, the vehicle ECU will save related data at that moment to generate a freeze frame. It is usually used to analyze the root cause that triggers the fault code, together with fault codes and PID data.
  • Actuator Tests: Also referred to as bi-directional controls, verify the operation of specific actuators—including solenoids, valves, and relays.
VDIAGTOOL D100 app showing OE-Level Full System Diagnostic menu

Image: VDIAGTOOL D100 app showing OE-Level Full System Diagnostic menu with various car systems and diagnostic functions.

VDIAGTOOL D100 performing Bi-Directional Tests

Image: VDIAGTOOL D100 performing Bi-Directional Tests, showing app controlling car functions like horn, windows, mirrors, and throttle.

4.5 OBD II Functions

  • OBDII Protocols: Global OBD uses the following five communication protocols: SAE J1850 PWM, SAE J1850 VPW, ISO 14230-4 (KWP2000), ISO 9141-2, ISO 15765-4 / SAE J2480.
  • Auto Scan & Protocol Selection: There are two methods to access OBDII data from the connected vehicle: Auto Scan (diagnostic tool automatically attempts to communicate using each available protocol) and Protocol Selection (manually select if vehicle's protocol is known).
  • Help: This section provides support information, including DLC location, a DTC library, common abbreviations, and background details such as OBDII modes.
  • Modes of OBDII: Menu options typically include: Read Trouble Code (Stored, Pending, Permanent), Clear Trouble Code, Live Data, Read Freeze Frame, Read ECU Information, Component Test (Mode $08), On-Board Monitor Test (Mode $06), O2S Monitoring Test (Mode $05), I/M Readiness (Smog Check).
VDIAGTOOL D100 app showing full OBD2 functions

Image: VDIAGTOOL D100 app showing various full OBD2 functions including Read Trouble Code, Clear Trouble Code, Live Data, Component Test, On-Board Monitor Test, Read Freeze Frame, Read ECU Information, O2S Monitoring Test, I/M Readiness, and Read Vehicle Info.

4.6 Special Functions (17+ Maintenance Functions)

This chapter introduces various scheduled service and maintenance functions, also referred to as "Special Functions". These functions are typically presented as a series of menu-driven executable commands. By following the on-screen instructions—selecting appropriate options, entering correct values, and performing necessary actions—you will be guided through the complete process of executing each function.

Since vehicle configurations vary by model, specific operation steps for each function are not listed here. In general, please follow the prompts displayed on the tool screen.

The VDIAGTOOL D100 OBDII car scanner comes equipped with 17 special functions, allowing you to maintain your car in optimal condition through regular vehicle maintenance and save significant dealership costs. As a professional scanning tool, it can handle almost any car repair scenario you can imagine. Don't worry, even beginners will find it simple and convenient to use.

VDIAGTOOL D100 showing 17+ Hot Maintenance Functions

Image: VDIAGTOOL D100 displaying 17+ Hot Maintenance Functions such as Oil Reset, Throttle Reset, ABS Bleeding, and more.

Special functions vary across models. The table below outlines all the special functions supported by the D100 and D200 respectively:

Supported Special Functions (D100)
# Special Function D100
1Oil Reset✓
2EPB✓
3SAS✓
4DPF/GPF✓
5BMS Reset✓
6TPMS Reset✓
7ABS Bleeding✓
8Injector Coding✓
9Gearbox Match✓
10Airbag Reset✓
11Crank Sensor Relearn✓
12Tire Size Reset✓
13Seat Calibration✓
14Throttle✓
15Control Unit Reset✓
16Suspension✓
17Windows Initialization✓

Detailed Special Functions:

  • Oil Reset: Resets the engine oil life cycle, clearing old data in the oil monitoring system after an oil change.
  • EPB (Electronic Parking Brake Reset): Resets the electronic parking brake system, typically used after replacing brake pads or servicing the braking system.
  • SAS (Steering Angle Sensor Reset): Calibrates the steering angle sensor to ensure accurate steering response and stability control.
  • DPF/GPF: Resets the DPF/GPF, addressing carbon buildup and ensuring the proper functioning of the emission system.
  • BMS Reset: Resets the battery management system, usually performed after replacing the battery, ensuring compatibility with the vehicle's system.
  • Throttle Reset: Calibrates the throttle position sensor to ensure optimal throttle response and fuel efficiency.
  • TPMS Reset: Resets the tire pressure monitoring system, reactivating it after tire replacement or adjustment.
  • Control Unit Reset: Resets the vehicle's electronic control unit, clearing stored error codes and restoring normal system operation.
  • Seat Calibration: Calibrates the seat's electric adjustment system, ensuring the seat position aligns with preset values.
  • ABS Bleeding: Bleeds air from the ABS system, ensuring brake stability and performance.
  • Injector Coding: Resets the injector codes to ensure proper fuel delivery and engine efficiency.
  • Airbag Reset: Clears error codes from the airbag system after a collision, restoring the system to its normal operating condition.
  • Gearbox Match: Matches the gearbox to the vehicle control unit after replacement or repair, ensuring smooth shifting.
  • Tire Size Reset: Resets the system to accommodate new tire sizes, ensuring accurate speed and fuel consumption readings.
  • Crank Sensor Relearn: Performs a relearn process for the crankshaft position sensor after replacement, ensuring accurate engine ignition and operation.
  • GPF: Captures soot particles in the exhaust gas of the diesel engine. After regeneration or replacement of the GPF, the GPF/DPF warning light can be reset on the instrument panel.
  • Camshaft Sensor Learning: After replacing the camshaft, timing chain or VVT solenoid valve, the phase of the variable valve timing system can be calibrated to ensure accurate intake/exhaust timing, improve combustion efficiency, and reduce knocking or insufficient power problems.

4.7 Advanced Functions (Paid Upgrades)

The VDIAGTOOL D100 offers extendable functionality through paid upgrades to cater to more advanced diagnostic needs.

  • J2534 Programming ($199, Lifetime Free Updates): Transforms the D100 into an advanced automotive diagnostic and reprogramming tool, supporting the J2534 protocol. This enables compatibility with OEM software for ECU programming, module flashing, and advanced dealer-level diagnostics. Requires a computer (Windows 7/8/10/11) and OEM software (not included).
  • 49+ Advanced Reset Functions ($169, 3 Years Valid): Unlocks additional advanced special functions (excluding IMMO, EEPROM, and ADAS) for more complex repair needs. Examples include AdBlue Reset, Write VIN, Clutch Adaption, TCM Oil Reset, Speed Limit, Stop/Start Reset, Rain/Light Sensor, Nox Reset, EGR Relearn, VGT Relearn, and more.

How to activate J2534/49+ reset functions:

  1. Click "Mall" in the app.
  2. Select the function you need.
  3. Make payment & get activation code.
  4. Enter the code in "Subscription" to activate the function.
VDIAGTOOL D100 app showing activation steps for advanced functions

Image: VDIAGTOOL D100 app interface demonstrating the steps to activate additional functions through the 'Mall' section.

5. Maintenance & Software Management

5.1 Report

After completing diagnostics and returning to the main screen, tap Save in the report generation form to create a diagnostic report. This report can be reviewed or shared later.

The report is available in two types:

  • Diagnosis Report: Automatically generated after performing diagnostic operations (auto-scanning, reading ECU information, retrieving trouble codes, or viewing live data). Can also be manually generated by selecting DTC Report in the diagnostic menu. All saved reports are available under the Report menu, where you can compare results, view details, or delete reports as needed. Reports can be shared via email or exported as a PDF file.
  • CSV View (Data Playback): This feature enables you to replay recorded live data from the diagnostic process. Data recording begins only when you tap the Data Recording button during a live data session, and valid data is being displayed. Recorded files can be accessed via Me → Related to me → CSV View. Note: Recorded CSV View sessions cannot be exported and can only be played within the app.
VDIAGTOOL D100 app showing professional diagnostic reports

Image: VDIAGTOOL D100 app displaying professional diagnostic reports, with options for instant save & share, CSV/PDF export, and smart issue flags.

5.2 Application Center

Application Center is a comprehensive hub designed to expand your diagnostic capabilities. It offers advanced tools and features to help you monitor, analyze, and troubleshoot vehicle systems efficiently. Key functions include:

  • Performance Test: Evaluate engine performance and identify potential issues through real-time diagnostics.
  • Smog Check: Conduct emissions testing to ensure compliance with environmental regulations.
  • Mode 6: Access detailed diagnostic data for deeper analysis of vehicle systems.
  • MIL Status: Check the status of the Malfunction Indicator Light (MIL) to quickly identify active faults.
  • OBD DTC Query: Retrieve and interpret Diagnostic Trouble Codes (DTCs) for precise troubleshooting.
  • Vehicle Coverage: Check the compatibility. However, this is for reference only. For better compatibility confirm, please provide your device S/N, your vehicle VIN and the desired functions to our tech support team at support@vdiagtool.com.
  • Warning Light Symbols: Identify and understand all dashboard warning lights, with detailed explanations for their causes.

5.3 Me (Profile)

Profile serves as your personalized control center, where you can manage account settings, device configurations, and system updates. This section allows you to:

  • Customize Your Profile: Change your username and profile picture for personal identification.
  • My Device: View essential details including model, serial number. You can also add another device or unbind your current device.
  • CSV View: Replay Live Data recording.
  • Subscription Service: Review active plans and available renewal options.
  • Firmware Upgrade: Download the latest firmware to maintain peak device performance.
  • Software Management: Manage installed applications and diagnostic modules.
  • Other Settings: Configure preferences including language, units, and display options.

5.4 Other Settings

Tap the Other Settings to adjust the default settings and view the information of the app. There are several options available in the system setting:

  • Language: The languages supported by the device are listed in Settings. The default language is set as English. If you need to switch to other languages, please contact the dealer or reach out to the tech support at support@vdiagtool.com to authorize the new language.
  • Unit: This setting provides 3 sets of units to measure various sensor values: Metric Units (Centimeters, kilometers, grams, kilo, °C, litres, pa, kpa), Imperial Units (Inch, foot, yard, oz, lb, °F, PSI, mile, gallon), US Units (Inch, foot, yard, oz, lb, °F, PSI, mil, mile).
  • Clear Cache: Quickly free up storage space and resolve performance issues by removing temporary system files and residual diagnostic data with one simple action.
  • About: Access essential information about your app including the current software version, User Agreement, Privacy Policy, and support contacts in one convenient location.

5.5 Update

All the available software is shown on this page. You can choose to download the specific software individually by tapping the arrow button next to the required software or choose to update all available software at once by tapping Updates.

VDIAGTOOL D100 app showing software update screen

Image: VDIAGTOOL D100 app displaying the software update screen, indicating lifetime free updates for newly added functions, software optimization, new car coverage, and bug fixes.

6. Troubleshooting

  • Connection Issues: If the device does not connect, ensure it is firmly seated in the OBD-II port and the vehicle engine is running. Verify Bluetooth is enabled on your phone and the device is paired. A green VCI indicator in the app confirms a successful connection.
  • Auto Scan Failure: If Auto Scan fails to identify the vehicle, try the "Diagnosis" option and manually select the vehicle or use "Automatic Detection."
  • VIN Not Decodable: If the vehicle VIN cannot be decoded automatically, try manual vehicle selection.
  • Language Change: The default language is English. To change to another language, contact VDIAGTOOL support with your device's serial number to authorize the new language.
  • App Performance: If the app experiences performance issues, try clearing the cache in "Me (Profile) > Other Settings > Clear Cache."
  • DTC Repair Guide: After detecting a fault code, users can look up the meaning of the fault code and repair solutions (cause, steps, methods) within the app, reducing repair difficulty and shortening troubleshooting time.

7. User Tips

  • Language Activation: If your desired language is not immediately available, contact VDIAGTOOL support with your device's serial number. They are responsive and can help activate additional languages.
  • Regular Updates: Take advantage of the lifetime free updates to ensure your scanner is compatible with the latest vehicle models and diagnostic protocols.
  • Diagnostic Reports: Utilize the diagnostic report feature to save, export, and share PDF reports for easy tracking of vehicle history and maintenance.
  • Bi-Directional Control: For quicker fault isolation, use the bi-directional control to test specific components directly, such as mirrors, windows, or throttle.

8. Specifications

Attribute Value
Communication InterfaceOBD-II
Free Update PeriodLifetime
Battery IncludedNo
Display SizeOthers (App-based)
Wireless SupportBluetooth 5.2
Special FeaturesBluetooth, Full Systems Diagnostic, All 10 OBD2 Modes, Active Test (Bi-direction control), 17+ Reset Functions, Auto VIN, 8-in-1 Live Data, Smog Check, Performance Test, OBD DTC Lookup
Software UpdateYes (Online Upgrade By App)
Software Version2026
Hardware Version2026
Brand NameVDIAGTOOL
OriginMainland China
Item TypeCode Readers & Scan Tools
CertificationCE
Item Height9 cm
Item Length5 cm
Item Width2.6 cm
Item Weight0.3kg
Supported SystemsAll systems & All functions
Upgrade MethodOnline Upgrade By App
Work SystemIOS/Android
Operated MethodVia Mobile Application
Supported LanguagesArabic, Japanese, Traditional Chinese, Korean, Dutch, Danish, German, Thai, Greek, Polish, English, Portuguese, Spanish, Russian, Swedish, Finnish, Turkish, French, Vietnamese, Hungarian, Italian (22+ Kinds Language)
Connection MethodBluetooth Scanner
Compatible ProtocolsCANFD, FCA (J2534 needs extra payment)

Package Contents:

  • VCI Main Unit
  • User Manual (PDF available for download: View PDF)
  • Type C Cable
  • Tool Kit (carrying case)
VDIAGTOOL D100 product package contents

Image: Contents of the VDIAGTOOL D100 package, including the VCI main unit, user manual, Type C cable, and tool kit.

9. Compliance Information

9.1 Regulatory Compliance Statements

United States (FCC)

FCC ID: 2BE93W02

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Interference Guidance: If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Canada (ISED)

IC: 32118-W02

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

9.2 RF Exposure & SAR (FCC & ISED)

This device complies with FCC and ISED Canada RF exposure guidelines. Its radiated output power is below the radio frequency exposure limits. The Specific Absorption Rate (SAR) is measured using standard operating positions with the device transmitting at its highest certified power level. The FCC SAR limit is 1.6 W/kg. The device is designed to operate at multiple power levels to minimize exposure and uses only the necessary power to maintain communication. To ensure compliance with RF exposure requirements, minimize human contact with the antenna during normal operation.

9.3 Additional Compliance (RoHS, CE & UKCA)

  • RoHS: This product is compliant with Directive 2011/65/EU on the restriction of hazardous substances.
  • CE: This product conforms to the essential requirements of the following European Directives: EMC Directive 2014/30/EU, RED Directive 2014/53/EU, Low Voltage Directive 2014/35/EU.
  • UKCA: This product is declared to conform to the essential requirements of the relevant UK statutory instruments and carries the UKCA mark accordingly.

10. Warranty & Support

10.1 Limited Two-Year Warranty

VDIAGTOOL warrants that the VCI device shall be free from defects in materials and workmanship for a period of two years (24 months) from the date of delivery to the original buyer.

This warranty does not cover any part that has been subjected to misuse, alteration, used for unintended purposes, or operated in a manner inconsistent with the product instructions. The exclusive remedy for any tool found to be defective under this warranty shall be, at VDIAGTOOL's option, repair or replacement of the product. VDIAGTOOL shall not be liable for any consequential or incidental damages arising from the use or inability to use the product.

10.2 Contact Us

Warranty & Support:

Training Videos:

Free product operation videos are available:

  1. Visit Training Center: https://www.vdiagtool.com/support/training-center
  2. Select Diagnostic Tools category.
  3. Watch model-specific tutorials.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.