ATORCH Electronic Load Protection Shell Box

Introduction

This manual provides instructions for the assembly and care of your ATORCH Electronic Load Protection Shell Box. This 3D-printed enclosure is designed to protect your compatible ATORCH DL24, DL24P, or BW150 electronic load tester. Please ensure you have the correct shell version for your specific electronic load model.

Setup and Assembly

The protection shell is provided as a kit and requires assembly. It consists of a top shell, a bottom shell, a fan grill, screws, and standoffs. The assembly process involves carefully placing your electronic load tester into the shell components.

Compatibility Check

Before assembly, verify that you have the correct shell version for your electronic load tester. The shells are designed for specific versions (V0, V1, V2) of the DL24, DL24P, and BW150 series. Refer to the images below to identify your model and the corresponding shell kit.

Figure 1: DL24 V2 Shell Kit components, including top and bottom shell, fan grill, screws, and standoffs. Suitable for New DL24 series.

Figure 2: DL24P V2 Shell Kit components. Suitable for New DL24P series.

Figure 3: DL24 V0 Shell Kit components. Suitable for Old DL24 series.

Figure 4: DL24P V0 Shell Kit components. Suitable for Old DL24P series.

Figure 5: BW150 V1 Shell Kit components. Suitable for New BW150 series.

Assembly Steps (General)

1. Carefully unpack all components of the shell kit and your electronic load tester.
2. Place the electronic load tester's main board into the bottom shell, aligning the mounting holes.
3. Secure the main board using the provided standoffs and screws.
4. Position the fan grill over the fan on the electronic load tester, ensuring proper alignment for airflow.
5. Place the top shell over the assembled unit, ensuring all ports and buttons align correctly.
6. Fasten the top and bottom shells together using the remaining screws.

Note: The V2 version shells feature upgraded speaker holes for improved audio output from the electronic load tester.

Figure 6: V2 version shell highlighting the upgraded speaker holes.

Assembled Product Examples

Figure 7: Assembly rendering of an old DL24 model with the protection shell.

Figure 8: Assembly rendering of a BW150 model with the protection shell.

Figure 9: Assembly rendering of a new DL24P model with the protection shell.

Operating the Protection Shell

This product is a protective enclosure. Once correctly assembled, it passively protects your ATORCH electronic load tester from physical damage, dust, and accidental contact. There are no specific operational steps for the shell itself. Operate your electronic load tester as per its own instruction manual.

Maintenance

• Cleaning: Use a soft, dry cloth to wipe the exterior of the shell. For stubborn dirt, a slightly damp cloth with mild soap can be used, followed by drying thoroughly. Avoid abrasive cleaners or solvents.
• Inspection: Periodically inspect the shell for any cracks, damage, or loose screws. Ensure the fan grill remains clear of obstructions to allow proper airflow for the electronic load tester.
• Storage: When not in use, store the assembled unit in a clean, dry environment away from direct sunlight and extreme temperatures.

Troubleshooting

Shell does not fit the electronic load tester:

Ensure you have purchased the correct shell version (DL24 V0/V2, DL24P V0/V2, BW150 V1) for your specific electronic load tester model. Refer to the compatibility section and images. This shell is not suitable for other styles or brands.

Screws do not tighten:

Avoid over-tightening screws, as this is a 3D-printed product and excessive force can damage the plastic threads. If a screw is stripped, it may require a slightly larger screw or thread repair.

Cracks or damage to the shell:

The shell is 3D printed. While durable, it can be damaged by excessive force or drops. If significant damage occurs, consider replacing the shell to maintain protection for your electronic load tester.

Specifications

User Tips

• Always confirm the exact model and version of your ATORCH electronic load tester (e.g., DL24 V2, BW150 V1) before purchasing a protection shell to ensure compatibility.
• Be aware that these shells are 3D printed, which may result in minor surface imperfections characteristic of the manufacturing process.
• While the current shells are available in specific colors, user feedback indicates interest in a wider range of color options. Check with the seller for potential future availability.

Warranty and Support

For any questions regarding the product, assembly, or potential defects, please contact the ATORCH Innovative Manufactory Co., Store directly through your purchase platform. Specific warranty details for this accessory may vary; please refer to the seller's policies at the time of purchase.