Introduction
Thank you for choosing the LEHX L6 Pro 7-inch 2-Din Android Car Radio Multimedia Stereo Receiver. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure you get the best experience from your device. Please read this manual thoroughly before installation and use.
Important Safety Note: Before installing the product, please test the unit to ensure it functions correctly, as long journeys may affect its performance. Professional installation is recommended.
Setup and Installation
Rear Interface Description
The following diagrams illustrate the rear interface connections for the car radio. Ensure all connections are secure and correctly matched to avoid damage or malfunction.

Power Plug Connections:
- Yellow (BATTERY): Constant 12V positive power supply. This maintains memory function.
- Red (ACC): Ignition switch 12V positive power supply.
- Black (GND): Ground wire.
- Orange (ILLUMINATION): Connects to backlight illumination.
- Pink (REVERSE): Reversing camera control line.
- Brown (KEY2) & Orange/black striped (KEY1): Steering Wheel Control lines.
- Blue (ANT): Auto Antenna Power.
Audio/Video/USB Connections:
- F-CAM (VIDEO-IN-2): Video Input 2 (Front Camera Input).
- AUX R IN / AUX L IN: Right / Left Audio Input.
- VIDEO-IN-1 / VIDEO OUT: Video Input 1 / Video Output.
- FR OUT / FL OUT: Front Right / Left Audio Output.
- SUB WOOF: Subwoofer Output.
- MIC: Microphone Input.
- AMP CONT: Amplifier Control.
- BT Antenna: Bluetooth Antenna.
- R-CAM: Reversing Camera Input.
- WiFi Antenna: Wi-Fi Antenna.
- USB1/2: USB Ports.
Important Wiring Notes:
- When both the yellow (B+) and red (ACC) lines receive 12V positive power simultaneously, the unit will power on.
- The yellow (B+) line must maintain power for the machine's memory function.
- Speaker cables (8 total): Each speaker cable must not be grounded, shared, or touch other lines. Incorrect wiring can lead to no sound, distorted sound, or overheating.
CANBUS Connection
CANBUS connection is required for certain car models to integrate with vehicle systems.


Attention: If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.
Reversing Camera Installation
Follow these steps to install the reversing camera:
- Locate the reverse control line on the unit's power line (usually pink). Connect this line to the 12V positive pole of the reverse light. The screen should turn blue.
- Locate the CAM video input interface on the back of the unit.
- Connect the camera:
- The red socket of the camera connects to the power cable.
- The yellow socket of the camera inserts into the video cable.
- The red wire of the camera's power cable and the red wire of the video cable are screwed together to the positive pole of the reverse lamp.
- The black wire of the camera's power cable is not used.
- The other end of the video cable connects to the CAM video input interface on the back of the unit.
- The red line coming out of the video line connects to the reverse control line of the power line.

Note: If the reversing camera is not installed, do not connect the REVERSE/BACK cable. Leave it unconnected to prevent display issues or the unit automatically entering reverse mode, which can cause malfunction.
Operating Instructions
CarPlay and Android Auto
The LEHX L6 Pro supports both Apple CarPlay and Android Auto for seamless smartphone integration.

Apple CarPlay (for supported models):
- Wired Connection: Connect your iPhone using a USB data cable. The unit will automatically enter the CarPlay interface.
- Wireless Connection: Turn on Bluetooth and Wi-Fi on your iPhone. Connect to the unit's Bluetooth. The unit will then automatically enter the CarPlay interface. (Signal is transmitted via Wi-Fi; CarPlay will remain connected even if Bluetooth is turned off. If Wi-Fi is turned off, CarPlay will disconnect.)
Android Auto (for supported models):
- Ensure "Google Play" services are available locally and download/install the "Android Auto" app.
- Use an Android phone with OS 6.0 or higher and a valid USB data cable.
- Wired Connection: Connect your Android phone using a USB data cable. The unit will automatically enter the Android Auto interface.
- Wireless Connection: Turn on Bluetooth and Wi-Fi on your Android phone. Connect to the unit's Bluetooth. The unit will then automatically enter the Android Auto interface. (Signal is transmitted via Wi-Fi; Android Auto will remain connected even if Bluetooth is turned off. If Wi-Fi is turned off, Android Auto will disconnect.)
Steering Wheel Controls Learning
To configure steering wheel controls:
- Press and hold a button on your car's steering wheel.
- On the unit's screen, find the corresponding button icon for that function.
- Click the icon on the screen to change its color. Successful learning is indicated by the color change.

Voice Control
The unit supports voice commands for various functions, enhancing driving safety and convenience.

Bluetooth Functionality
The LEHX L6 Pro features a built-in smart Bluetooth system (BT5.1) for mobile phone pairing, music streaming, and hands-free calling.

To use Bluetooth:
- Turn on the unit.
- On your mobile phone, search for the unit's Bluetooth name.
- Click "Connect".
- Once connected, you can answer calls or play music via Bluetooth.
DAB+ Tuner (Optional)
Enjoy high-quality digital audio broadcasting with the optional DAB+ radio receiver stick, connected via USB.

OBD2 Support (Optional)
The unit supports OBD2 diagnostics via a Vgate Icar2 Bluetooth adapter, allowing you to monitor vehicle data on the screen.

TPMS (Tire Pressure Monitoring System) (Optional)
An intelligent four-tire pressure detector can be connected to visualize real-time tire temperature and pressure. Alarms are activated if limits are exceeded.

Video Output (Optional)
The video output function requires the purchase of additional accessories to use, allowing display on external screens.

DVR (Driving Video Recorder) (Optional)
The LEHX L6 Pro version supports the LEHX USB ADAS X8 DVR for map navigation, driving recording, and window display.

Maintenance
Keep the unit clean by wiping it with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners. Ensure all connections remain secure. If the unit requires service, contact customer support.
Troubleshooting
1. Cannot boot normally
- Wiring Check: Ensure the "Yellow" (B+), "Red" (ACC), and "Black" (GND) wires are all connected correctly. Yellow to positive, Red to key control, Black to negative. If only two lines are connected, or connections are incorrect, the unit will not boot.
- Original Car Wiring: Do not connect the unit's wiring directly to the original car's color-coded wires if they are non-standard. This can cause damage.
- Original Car Plug: Do not plug the original car plug directly into the new unit. It may not work or cause damage.
- Fuse Check: If the 3 wires are connected correctly but it doesn't boot, check the fuse on the yellow line. If the fuse is intact, twist the yellow and red wires together, turn on the key, and press the power button to test.
- Repeated Fuse Burning: If the fuse burns every time it's replaced, stop replacing it. This indicates a short circuit in the unit's protection circuit. The unit requires professional repair.
- Final Test: If all checks fail, connect the yellow and red wires to a 12V battery's positive terminal, and the black wire to the negative terminal. Press the power button. If it boots, the original car wiring is faulty. If it doesn't boot, the unit is defective.
2. Automatic shut-down
- Cable Error: If the blue cable (automatic antenna power supply) is connected to the unit's power cable, it will automatically shut down. Correct the wiring.
- Unstable Voltage: Test the power supply with a stable 12V-5A source. If the unit still shuts down automatically, the power supply is faulty. If it works correctly with the test power supply, the unit is faulty.
3. Noise issues
- Low Speaker Power: If the original speaker power is too low, noise will occur when the volume is turned up. Solution: Avoid excessively high volume.
- Grounded Speaker Cable: If a speaker cable is grounded, take the iron speaker cable and connect it directly to the unit's speaker cable.
4. Remote control cannot be used
- Test Method: Use your phone camera to point at the remote control's light and press a button. If the light doesn't illuminate, replace the battery. If it illuminates, the remote control is functional.
5. Settings cannot be saved (no memory)
- The yellow (B+) and red (ACC) lines are connected together (they should be separate).
- The yellow and red lines are reversed (swap their positions).
6. Bluetooth not working
Ensure the unit's Bluetooth is turned on. Search for the unit's Bluetooth name on your mobile phone and connect. If issues persist, check Bluetooth settings.
7. Product emits smoke
Replace the FUSE. If the problem persists, the internal circuit is burned and requires after-sales service.
8. Sound cannot be adjusted
- Reset the unit or unplug and replug the power cord.
- The volume knob may be broken and needs replacement.
9. Reversing camera does not display
- Wiring Issues: Check for incorrect or missing wiring. Ensure all camera accessories (camera, power cord, video cable) are connected.
- Broken Camera: If the camera is correctly wired but doesn't light up, it may be broken and needs replacement.
10. USB devices cannot be played
Format the USB flash drive to FAT32. Re-download one or two songs and try again. If it still doesn't work, replace the USB flash drive.
11. FM does not receive radio stations
- The antenna plug is not fully inserted, or the antenna/line is disconnected.
- Search for stations using the "AS" button for automatic search, or use the "before/after" buttons.
- If the above points don't resolve the issue, unplug the antenna plug and insert a screwdriver or metal strip instead of the antenna to test.
12. No sound right after installation
If there is no sound immediately after installation, it's usually a wiring error or a short-circuited original car speaker wire. To check:
- Check if the speaker cable is short-circuited and connected. Reconnect if necessary.
- Verify the number of speaker cables. If only 2 speaker cables are present, and the original car line requires 4, you need to re-route the original car line. One speaker needs 2 speaker wires; two speakers need 4 speaker cables.
13. No sound after a while
Disconnect all speaker cables from the unit (do not remove them). Find an external speaker and connect it to the gray and purple wires of the unit's tail line. Connect any group to green and check for sound. If there is sound, the car's speaker line is short-circuited or the speaker is damaged. If there is no sound, the unit is broken.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | LEHX |
| Din | Double Din |
| Display Size | 7", 9", 10.1" (Optional) |
| Resolution | QLED 1280*720 |
| Operating System | Android |
| RAM | 6G (Various configurations available, e.g., 4G, 8G) |
| ROM | 64G (Various configurations available, e.g., 128G) |
| Max External Memory | 128G |
| Out Power | 50*4 W |
| Voltage | 12 V |
| Item Weight | 1kg |
| Item Size | 230*130*220 mm |
| Is touch screen | Yes |
| Built-in Screen | Yes |
| TF/Micro SD Slot | 0 |
| Interface | OPTION (USB, RCA, Bluetooth) |
| Special Features | Built-In Speaker/Microphone, WiFi function, Support 4G Network, Built-in GPS, Mobile Phone, MP3 players, Voice Control, DSP, CarPlay, Android Auto, Reversing Input, Split Screen, Support steering wheel control |
| Digital Media Format | CD, DVD-R/RW, DVD-RAM, VIDEO CD, Mp3, MP4, WMA, JPEG |
| OSD Language | Multi-language support including English, Spanish, Russian, French, German, Italian, etc. |
| Certification | CE |
| Material | ABS+ |
| For Vehicle Brands/Model | Universal (For Volkswagen, Nissan, Hyundai, Kia, Toyota, Jeep, Fiat, etc.) |
| Subwoofer Output | Support |
| AV-OUT | WiFi version support |
| RCA cable | 7 channels including subwoofer cable |
| Rear view camera input | Support (Free Gift) |
| INPUT Interface | 2*USB RCA Bluetooth |
| WIFI | Built-in |
| Steering wheel control | Support |
| Microphone | Built-in (external microphone optional) |
| GPS Navigation map | Built-in offline map free update (support Navitel/Igo) |
| Bluetooth phone book | Support |
| Bluetooth music | Support |
User Tips
- Compatibility Check: Before purchasing, it is highly recommended to contact customer service to confirm if the frame and cables are suitable for your specific car model (e.g., Toyota Yaris 2009, Kia Sportage 2020-2021, Seat Ibiza 6L). This prevents wasted time and ensures proper fitment.
- Professional Installation: For optimal performance and to avoid damage to your vehicle's dashboard or the unit, professional installation is strongly advised.
- Firmware Updates: Be aware that if the device is updated, functions may change without prior notice.
- Memory Usage: The operating system and pre-installed applications will occupy a portion of the internal memory. For example, the Russia map requires about 2.8GB, and the Europe map requires about 6.8GB.
- Boot Logo Customization: You can change the boot logo via Settings > Car Information > General > Boot Logo. Use password 8888 for L6/L6Plus or 3368 for L6 Pro, then select your desired logo.
Warranty and Support
The LEHX L6 Pro comes with a 1-year warranty. All products undergo strict quality tests before leaving the factory.
For technical assistance or any questions regarding the product, delivery, or service, please contact LEHX customer service. Do not leave negative feedback or open disputes without prior communication.
A user manual in PDF format is available for download: View User Manual (PDF)
For more help, you can contact customer service via:
