Introduction
Thank you for choosing the Kysplosion 12V Cordless Stubby Electric Screwdriver. This manual provides essential information for the safe and efficient operation, maintenance, and care of your new tool. Please read through carefully and understand these instructions before use to ensure optimal performance and safety.
Kysplosion 12V Cordless Stubby Electric Screwdriver
General Safety Instructions
WARNING: Always remove the battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.
WARNING: To reduce the risk of injury, wear safety goggles or glasses with side shields.
- Always ensure the tool is shut down and the battery pack is removed before any adjustments, accessory changes, or maintenance.
- Operate the machine only when there is sufficient light or good illumination.
- Do not extend the tool too far and always make sure to stand firmly.
- Keep hands away from rotating parts.
- Do not use the tool if it is damaged or vibrating abnormally.
- Prevent accidental start-up. Ensure the switch is in the off position before connecting the power supply or battery pack.
- Do not immerse the tool, battery, or charger in any liquid.
- Keep out of reach of children.
Product Overview
The Kysplosion 12V Cordless Stubby Electric Screwdriver is a versatile tool designed for various applications including home decoration, drilling, fastening, and screwing. It features a compact, lightweight design and brushless motor technology for efficient performance.
Compact design with lighting function for narrow spaces.
Versatile applications including drilling and screwing with torque adjustment.
Specifications
Product variations and key specifications.
| Feature | Specification |
|---|---|
| Battery Voltage | 12V (general dr. battery) |
| Motor Type | Pure copper brushless strong magnetic motor |
| Torque | 168 Newton Meters (Nm) |
| Drilling Diameter (Wood/Steel) | 10 mm |
| No-load Rate (Speed 1) | 0-500 rpm |
| No-load Rate (Speed 2) | 0-2200 rpm |
| Body Weight | 0.8 kg (approx.) |
| Battery Capacity (if included) | 2000mAh (Ternary lithium battery) |
The tool is available as a bare machine (no battery) or as a standard kit including one 12V battery and one charger.
Setup
Battery Charging
If your tool includes a battery, ensure it is fully charged before first use. For new battery packs or those unused for a prolonged time, charge for approximately 24 hours to bring them to full charge.
- Plug the charger into an AC outlet.
- Insert the battery pack firmly into the charger.
- During charging, the charging lamp will light up. When the charge is completed, an internal electronic switch will automatically trigger to prevent overcharging.
- If the battery pack is warm (e.g., immediately after heavy-duty operation), charging will not occur. The orange standby lamp will light up until the battery becomes cool, then charging will begin automatically.
- When charging is completed, the charging lamp will start flashing quickly.
- If the battery pack has not been used for a long time, the charging lamp starts flashing slowly to indicate protective charging. This process takes longer to fully charge the battery pack.
Charging Indicator Light States:
| Charge State | Indicator State |
|---|---|
| Charger Into The Power Source | Green on, Red off |
| Charging | Green off, Red on |
| After Charging | Green on, Red off |
| Battery Abnormal | Green Red Flick |
| Battery Temperature Below 0°C or Over 45°C | Green off, Red Flick |
Bit Installation and Removal (Chuck)
- To mount the bit:
- Insert a bit into the mounting hole, and turn it slightly to locate an engaged position.
- At the engaged position, push the bit as far as it goes. Make sure that the bit is fixed by pulling it.
- To dismount the bit:
- Depress the chuck cover and pull the bit.
Note: This tool uses SDS PLUS type shank bits.
Depth Gauge Adjustment
To use the depth gauge:
- Loosen the support handle.
- Adjust the depth gauge to your desired depth.
- After adjusting, tighten the support handle to fix the depth gauge.
Operating Instructions
Using the Control Switch
The control switch has three positions: forward, reverse, and lock. The control switch can only be adjusted when the ON/OFF switch is not pressed. Always allow the motor to come to a complete stop before using the control switch.
- Forward (Clockwise) Rotation: Push the control switch in the direction indicated for forward operation. Always check the direction of rotation before use.
- Reverse (Counterclockwise) Rotation: Push the control switch in the direction indicated for reverse operation. Always check the direction of rotation before use.
- Lock: To lock the trigger, push the control switch to the center position. The trigger will not work when the control switch is in the locked position.
Always remove the battery pack before performing maintenance, changing accessories, storing the tool, and any time the tool is not in use.
Starting, Stopping, and Controlling Speed
This tool can be operated at any speed from 0 to full speed.
- To Start: Pull the trigger. An LED light will turn on when the trigger is pulled.
- To Vary Speed: Increase or decrease pressure on the trigger. The further the trigger is pulled, the greater the speed.
- To Stop: Release the trigger. The electric brake will stop the tool instantly.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the tighter it will become. To prevent damaging fasteners or workpieces, avoid excessive impacting. Be particularly careful when impacting smaller fasteners because they require less impacting to reach optimum torque.
- Practice with various fasteners, noting the length of time required to reach the desired torque. Check the tightness with a hand-torque wrench. If fasteners are too tight, reduce impacting time. If not tight enough, increase impacting time.
- Oil, dirt, rust, or other matter on the threads or under the head of the fastener affects the degree of tightness.
- The torque required to loosen a fastener averages 75% to 80% of the tightening torque, depending on the condition of the contacting surfaces.
- For light gasket jobs, run each fastener down to a relatively light torque and use a hand torque wrench for final tightening.
The tool features torque adjustment levels from 1 to 21 for starting screws, allowing for precise control.
Maintenance
- Bit Greasing: Grease the oval indentation on the bit with the supplied grease at least once a month.
- Cleaning: Keep the tool clean. Use a clean cloth to clean the tool and battery/charger (do not use any abrasive or solvent-based cleaning agents). Use a soft brush or a dry cloth to clean dust.
- Storage: Store the tool in a dry place, out of reach of children.
- Always remove the battery pack before storing the tool.
Troubleshooting
- Problem: Tool gets stuck when switching to drill mode.
- Possible Solution: Ensure the chuck is clean and free of debris. Try rotating the chuck slightly by hand while switching modes to help engage the mechanism. If the issue persists, contact support.
User Tips
- This screwdriver is noted for its power and suitability for workshop use.
- It is perfectly compatible with 12V Bosch professional batteries, offering flexibility if you already own Bosch 12V tools.
- Users find it to be a useful and effective tool for various tasks.
Warranty and Support
For detailed warranty information, technical support, or service inquiries, please refer to the official product documentation or contact the seller directly.
A comprehensive user manual in PDF format is available for download: View User Manual (PDF).