HITBOX ARC200E

Contents

HITBOX ARC200E 3-in-1 Welding Machine User Manual

MMA/Stick, Gasless MIG, and Lift TIG Welding

1. Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your HITBOX ARC200E 3-in-1 Welding Machine. Please read this manual thoroughly before using the equipment.

HITBOX ARC200E 3-in-1 Welding Machine

Figure 1: HITBOX ARC200E 3-in-1 Welding Machine

2. Safety Precautions

Always prioritize safety when operating welding equipment. Failure to follow safety guidelines can result in serious injury or death.

  • Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, protective clothing, and safety shoes.
  • Ensure adequate ventilation to avoid inhaling welding fumes.
  • Keep flammable materials away from the welding area.
  • Do not operate the machine in wet conditions.
  • Ensure proper grounding of the welding machine and workpiece.
  • Disconnect power before performing any maintenance or changing accessories.
  • The machine features Electrical Protection (overcurrent/overvoltage/overheating), VRD (Voltage Reduction Device) for safety, an Automatic Overload shutdown system, and an IP21S Water Rating.
Safety features of the HITBOX ARC200E welder including Electrical Protection, VRD, Overload shutdown, and IP21S Water Rating.

Figure 2: Safety and Reliability Features

3. Package Contents

Verify that all items listed below are included in your package:

  • 1x ARC200E Welder
  • 1x Earth Clamp 4.9ft
  • 1x Electrode Holder 4.9ft
  • 5x Welding Rods 2.0mm
  • 1x Hammer
  • 1x Product Manual
Included accessories: ARC200E Welder, Earth Clamp, Electrode Holder, Welding Rods, Hammer, Product Manual.

Figure 3: Included Accessories

4. Controls and Display

Familiarize yourself with the control panel and connections of the ARC200E welding machine.

Front panel of the ARC200E welder showing Digital LCD Screen, Rotate knob, Buttons for Welding Mode, Electrode Selection, Function Mode, '+' Pole, and '-' Pole.

Figure 4: Front Panel Controls and Connections

4.1 Front Panel

  • Digital LCD Screen: Displays welding parameters such as current, voltage, and selected mode.
  • Rotate Knob: Adjusts welding current and other parameters.
  • Buttons:
    • Welding Mode: Selects between MMA/ARC, Lift TIG, and Gasless MIG.
    • Electrode Selection: For MMA mode, selects electrode type (e.g., 6010, 6011, 6013, 7018).
    • Function Mode: Toggles features like Hot Start, Arc Force, Anti-stick, and VRD.
  • "+" Pole: Positive output terminal.
  • "-" Pole: Negative output terminal.

4.2 Rear Panel

Rear panel of the ARC200E welder showing Power Cable, Power Switch, and Cooling Fan.

Figure 5: Rear Panel Features

  • Power Cable: Connects the machine to the main power supply (AC 110V/220V).
  • Power Switch: Turns the machine ON/OFF.
  • Cooling Fan: Ensures proper cooling during operation.

5. Setup and Connections

Proper setup is crucial for safe and effective welding. Ensure the machine is turned OFF before making any connections.

5.1 Power Connection

  • Connect the power cable to a suitable AC 220V power outlet (EU Plug).
  • Ensure the power switch on the rear panel is in the OFF position before plugging in.

Video 1: Product Overview and Basic Connections (0:00 - 0:09 shows power connection)

5.2 Welding Mode Specific Connections

The polarity of connections varies depending on the welding process. Refer to the diagrams below for correct setup.

5.2.1 MMA (Stick) Welding Setup

  • Connect the Earth Clamp to the negative (-) output terminal.
  • Connect the Electrode Holder to the positive (+) output terminal.
  • Securely attach the Earth Clamp to the workpiece.
Diagram showing connections for STICK welding with 6011/7018 and 6010/6013 electrodes. Earth clamp to negative, electrode holder to positive.

Figure 6: MMA (Stick) Welding Connection Diagram

(Refer to Video 1, 0:10 - 0:16 for visual guide on connecting ground clamp and electrode holder)

5.2.2 Lift TIG Welding Setup

  • Connect the TIG Torch (WP17V torch, requires extra purchase) to the negative (-) output terminal.
  • Connect the Earth Clamp to the positive (+) output terminal.
  • Securely attach the Earth Clamp to the workpiece.
  • Ensure an Argon gas cylinder and regulator are connected to the TIG torch for shielding gas.
Diagram showing connections for LIFT TIG welding. TIG torch to negative, earth clamp to positive, and argon gas connection.

Figure 7: Lift TIG Welding Connection Diagram

(Refer to Video 1, 1:09 - 1:19 for visual guide on connecting TIG torch and ground clamp)

5.2.3 Gasless MIG (Flux MIG) Welding Setup

  • Connect the Spool Gun (requires extra purchase) to the designated spool gun terminal.
  • Connect the Earth Clamp to the positive (+) output terminal.
  • Securely attach the Earth Clamp to the workpiece.
  • This mode uses flux-cored wire, eliminating the need for external shielding gas.
Diagram showing connections for FLUX MIG welding. Spool gun connected, earth clamp to positive.

Figure 8: Gasless MIG Welding Connection Diagram

6. Operation

This section details the operational procedures for each welding mode.

6.1 General Operation Steps

  1. Ensure all connections are correct and secure for the desired welding mode.
  2. Turn on the power switch on the rear panel.
  3. Select the desired welding mode (MMA/ARC, Lift TIG, or Gasless MIG) using the "Welding Mode" button.
  4. Adjust the welding current using the "Rotate Knob". The large LCD screen will display the current settings.
  5. For MMA mode, select the appropriate electrode type using the "Electrode Selection" button.
  6. For advanced features like Hot Start, Arc Force, Anti-stick, and VRD, use the "Function Mode" button and "Rotate Knob" to adjust or toggle them.
  7. Begin welding, always observing safety precautions.
Close-up of the digital display showing settings for Hot Start, Arc Force, Antisticking OFF, and VRD.

Figure 9: Digital Display and Function Settings

Image illustrating adjustable Hot Start and Arc Force features for improved arc initiation and weld stability.

Figure 10: Adjustable Hot Start and Arc Force

Image showing ON/OFF Anti-stick and VRD features, providing operational options for welders.

Figure 11: Anti-stick and VRD Features

6.2 MMA (Stick) Welding

  • Use welding rods between 1.6-4.0mm.
  • Suitable for E6010, E6013, E7018 welding rods.
  • Welding thickness: 2-10mm.
  • Adjust current between 20A-160A.
  • The machine features Hot Start for easier arc ignition and Arc Force for stable welding.
  • Anti-stick function prevents the electrode from sticking.
MMA welding in progress, showing a smooth weld seam and indicating compatibility with 5/32 inch (4.0mm) welding rods.

Figure 12: MMA Welding Performance

(Refer to Video 1, 0:17 - 1:06 for MMA/ARC welding demonstration)

6.3 Lift TIG Welding

  • Requires a WP17V TIG torch (purchased separately) and Argon shielding gas.
  • Use TIG tungsten needles between 1.6-2.4mm.
  • Welding thickness: 1-4mm.
  • Adjust current between 15A-200A.
  • Lift TIG provides a stable arc for precise welding.

(Refer to Video 1, 1:07 - 1:49 for Lift TIG welding demonstration)

6.4 Gasless MIG (Flux MIG) Welding

  • Requires a spool gun (purchased separately).
  • Use MIG welding wire 0.8/1.0mm.
  • Welding thickness: 1-8mm.
  • Adjust current between 30A-160A.
  • This mode is suitable for welding without external shielding gas.
Flux MIG welding in action, showing a welder using a spool gun.

Figure 13: Gasless MIG Welding in Use

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  • Cleaning: Regularly clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to clear internal components if necessary, ensuring the machine is unplugged.
  • Cable Inspection: Periodically inspect all welding cables, electrode holders, and earth clamps for damage, fraying, or loose connections. Replace damaged components immediately.
  • Storage: Store the welding machine in a dry, clean environment, away from direct sunlight and extreme temperatures.
  • Electrode/Wire Storage: Store welding rods and wires according to manufacturer recommendations to maintain their quality.

8. Troubleshooting

This section covers common issues and their potential solutions. For problems not listed here, contact customer support.

ProblemPossible CauseSolution
No power to the machinePower cable disconnected, power switch off, circuit breaker tripped.Check power cable connection, turn on power switch, reset circuit breaker.
No arc in MMA/TIG modePoor ground connection, incorrect current setting, faulty electrode/tungsten.Ensure ground clamp is securely attached to clean metal, adjust current, replace electrode/tungsten.
Wire feeding issues in MIG modeIncorrect wire tension, clogged liner, wrong drive roller size.Adjust wire tension, clean or replace liner, ensure correct drive roller for wire size.
Machine overheats and shuts downExceeded duty cycle, blocked ventilation.Allow machine to cool down, ensure clear ventilation, operate within rated duty cycle.
Poor weld qualityIncorrect settings (current, voltage), improper technique, contaminated workpiece.Adjust settings according to material and thickness, practice technique, clean workpiece thoroughly.

9. Specifications

FeatureDetail
ModelARC200E
Dimensions (Machine)35 x 16 x 25 cm (13.58 x 6.3 x 8.66 inches)
Weight (Machine)4.31 kg (9.44 lbs)
Input VoltageAC 220V
Plug TypeEU Plug
MMA Current Range20A - 160A
MIG Current Range30A - 160A
TIG Current Range15A - 200A
Rated Duty Cycle60%
MMA Welding Rods1.6 - 4.0 mm (E6010, E6013, E7018)
MIG Welding Wire0.8 / 1.0 mm
TIG Tungsten Needle1.6 - 2.4 mm
Welding Thickness (MMA)2 - 10 mm
Welding Thickness (MIG)1 - 8 mm
Welding Thickness (TIG)1 - 4 mm
Welding MaterialsCarbon Steel, Iron, Galvanized Sheet, Stainless Steel
CertificationCE
Smart DeviceNo
Dimensions of the HITBOX ARC200E welding machine: 13.58 inches length, 6.3 inches width, 8.66 inches height, and 9.44 lbs weight.

Figure 14: Product Dimensions and Weight

10. User Tips

  • For optimal performance, ensure your workpiece is clean and free of rust, paint, or grease before welding.
  • Experiment with different current settings on scrap material to find the ideal parameters for your specific project and material thickness.
  • When using Lift TIG, ensure a consistent flow of Argon gas for proper shielding and a clean weld.
  • Take advantage of the Hot Start and Arc Force features in MMA mode to improve arc stability and reduce electrode sticking, especially for beginners.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official HITBOX website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

© 2024 HITBOX. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.