Heltecbms HT-SW01H/HT-SW02H

Contents

Heltec HT-SW01H/HT-SW02H Battery Spot Welding Machine User Manual

Super Energy-Gathered Pulse Technology for Phosphate Iron Lithium Power Battery Aluminum to Nickel Welding

1. Important Safety Information and General Attentions

Please read all safety information and instructions carefully before operating the machine.

  • The power inside the capacitor has been released for safe transportation before leaving the factory. When you receive the machine, please turn it on, charge it for about 18 minutes, and wait for the voltage to rise between 5.6~6V before spot welding.
  • Use the HeltecBMS adapter to work with the welding machine. An adapter from a third-party supplier will damage the device.
  • Always wear appropriate safety glasses and gloves during the welding process.
  • Removing the oxidation layer on welding pins is good for energy transfer and improves weld quality.
  • Unplug the machine when it is not in use.
  • The welding current displayed instantaneously is pulse release, and ordinary testing instruments cannot measure it accurately.
  • Welding materials should be cleaned before welding. Remove any oil stains or oxide layers on the surface to avoid poor welding.
  • Keep out of reach of children.
  • Unauthorized disassembly of the machine is not allowed and is unsafe.
  • Do not use the product in inflammable, explosive, or water-spray environments.

2. Product Overview

The Heltec HT-SW01H/HT-SW02H is a high-performance battery spot welding machine designed for precision welding of various battery types and metal sheets. It features super energy-gathered pulse technology for strong and reliable welds.

Key Features:

  • High-frequency inverter energy storage super capacitor discharge technology.
  • Patented energy storage control and low-loss metal bus technology.
  • Microcomputer-controlled energy-gathering pulse formation.
  • Automotive-grade large-capacity low-resistance super energy storage capacitors.
  • Intelligent program with multi-function parameter display screen.
  • Dedicated "aluminum nickel" welding mode for iron-lithium power batteries.
  • Maximum pulse welding current up to 3500A (HT-SW01H) / 7000A (HT-SW02H).
  • Dual-mode spot welding trigger (MT/AT) for precise and efficient welding.
  • Built-in safe self-discharge device.
  • Real-time display of welding pulse current.
  • Professional welding pens for various applications.

Product Video: HT-SW02H Battery Spot Welder in Action

This video demonstrates the HT-SW02H spot welding machine, highlighting its 42KW power and super energy-gathered pulse welding capabilities for concentrated and deep penetration solder joints.

3. Setup Instructions

3.1. Packing List

Please verify that all components are included in your package:

  • Main machine (1 pc)
  • Power adapter (1 pc)
  • Foot pedal (1 pc)
  • 75Amm² welding pen (1 pair)
  • Welding arm (73SA) (1 pc)
  • Hexagon spanner (1 pc)
  • Base (1 pc)
  • Welding pin on the welding arm (73SA) (2 pairs)
  • Welding pin on the welding pen (HB-75A) (1 pair)
  • User Manual & Warranty Card (1 pc)

3.2. Power Supply and Mobile Welding Pen Installation

  1. Plug the adapter into an AC 100-240 volt wall socket to charge the machine.
  2. Plug the power output plug into the spot welder's power connection port.
  3. Insert the mobile welding pen and ensure the connection is solid.

Note: The capacitor is released for safe transportation. Upon receiving the machine, turn it on, charge it for 20-30 minutes, and wait for the voltage to rise between 5.2-5.8V before spot welding.

3.3. Installation of Handle Controlled Welding Head (HSW01)

For models with the HSW01 column type pneumatic welding head:

  1. Insert the welding head into the corresponding socket on the main unit.
  2. Remove the lid of the welding head.
  3. Tighten the screws to secure the welding head. Ensure copper wires are separate.
  4. Close the lid.

Spot welder with column type pneumatic welding headColumn Type Pneumatic Welding Head (HSW01) connected to the spot welder.

Spot welder with air compressorColumn welding tools can be used with a variety of welding machines, requiring connection to an air compressor.

4. Operating Instructions

4.1. Control Panel Overview

HT-SW01H Spot Welder Control PanelHT-SW01H Spot Welder Control Panel showing display and buttons.

HT-SW02H Spot Welder Control PanelHT-SW02H Spot Welder Control Panel showing display and buttons.

The control panel features an LED operator interface, energy grade setting button, preloading delay select button, Aluminum to Nickel mode button, and Power button/Setting button. It also has a gather energy pulse output interface.

4.2. Basic Operation Steps

  1. Power On: Press the power button to turn on the welding machine.
  2. Initial Charge: If it's the first time powering on, the LED will show "CH" and the real-time voltage. Wait for about 18 minutes until the voltage rises to 5.6V or 6V.
  3. Set Energy Grade: Press the power button when the machine is on. The current number will flash. Use the UP/DOWN buttons to adjust the energy grade (0-99T).
  4. Select Welding Mode (MT/AT): Press the power and A/▼ buttons to switch between MT (foot pedal trigger) and AT (automatic induction) modes.
  5. Select Material Mode (NI-NI/AL-NI): Short press the AL/NI button. The button will light up. Wait 5 minutes after setting.
  6. Set Preload Delay (AT Mode Only): In AT mode, press the "" key to switch the required delay spot welding time. For 500ms, press and hold "LO MISS" until it stops flashing.
  7. Welding:
    • MT Mode: Hold the spot welding pen, press the welding needle tightly onto the workpiece, and step on the wire-controlled foot switch to trigger welding. Observe the real-time welding current.
    • AT Mode: Hold the spot welding pen, press the welding needle tightly, and the machine will automatically trigger welding after the set preload time.
  8. Power Off: Press and hold the "" key for 2 seconds to turn off the spot welding machine. Unplug the power adapter when not in use.

4.3. Welding Tool Options

Welding pen types and applicationsVarious welding pen types and their applications.

The machine supports different welding tools for various applications:

  • S-75A Split Spot Welding Pen: Ideal for single batteries and thick nickel sheets, offering good weld consistency.
  • Fixed Rocker Arm Push-Down Welding Tool: Suitable for welding battery packs or large-size batteries, providing high flexibility.

4.4. Welding Mode Selection Details

Trigger Discharge Welding Mode:

  • MT (Foot Trigger) Mode: Recommended for initial use or new weldments, as it allows for manual adjustment of parameters like current size, pulse width, and needle pressure.
  • AT (Automatic Induction) Mode: Once parameters are determined and proficiency is gained, this mode reduces work intensity and improves efficiency.

"Nickel-Nickel" and "Aluminum-Nickel" Mode:

  • AL-NI Mode: Specifically designed for direct welding of pure nickel connection pieces to high-current single lithium iron phosphate batteries. Provides greater energy output for firm welds on aluminum plates. Suitable for all aluminum and nickel sheets.
  • NI-NI Mode: For welding ternary lithium batteries, use this mode to avoid excessive welding current.

Selection of Welding Pulse Energy Width (Time):

  • The machine uses a "shaped energy pulse" for welding. Select an appropriate pulse width to achieve deep penetration without diffusion, heat, or blackening. Choose the smallest pulse time that ensures firm penetration.

Preload Delay Parameter Selection in AT Mode:

  • In AT mode, selecting appropriate preload delays helps match the welder's operation, preventing issues like large sparks or poor welding due to unstable pressure.

5. Maintenance

5.1. Welding Pin Maintenance

To ensure optimal welding efficiency and quality, follow these guidelines for welding tools:

  1. Regularly inspect welding pin heads for oxidation or blackening. If present, polish them with a fine abrasive cloth to restore brightness and smoothness.
  2. To prevent oxidation, apply a small amount of lubricating oil as an anti-oxidation coating on the welding pin.
  3. Only use the original nano-oxide aluminum alloy welding pins.
  4. If a welding needle becomes too short to be pulled out, and cannot be replaced, ensure at least 2mm of the needle is reserved for flat jaw pliers to clamp and pull it out from the needle seat.
  5. After installing a new welding needle into the clamp, solder it firmly to the clamp. Poor contact between the welding needle and the pen will negatively affect welding performance.

6. Troubleshooting

Refer to the table below for common issues and their solutions:

Error TypeIssuesSolutions
Weak welding
  • Welding pin polluted or oxidized
  • Capillary pressure not uniform
  • Welding pin blunt
  • Workpiece thickness exceeds range
  • Clean oxide layer on welding pins
  • Adjust welding pressure
  • Grind welding pins to a taper of 1-1.5mm
  • Select spot welders with appropriate power
Panel display "E01"
  • Spot welding electrodes touch each other
  • Welding pin oxidized
  • Avoid contact of welding pins/copper wires
  • Polish welding pin to clean oxide
Panel display "E02"
  • Trigger foot switch pressed continuously
  • Foot switch not bouncing back
  • Foot switch damaged
  • Avoid rapid succession within 0.5 seconds
  • Check for obstructions or spring issues
  • Replace foot switch cable or micro switch
Spot welding not firmWelder voltage is lower than 5.2VCharge to 5.2-6.0V with matching adapter. Effect above 6V is better.
MT does not workFoot switch is badReplace or repair the foot switch.
AT does not work
  • Parameters flashing and not confirmed
  • Welding material not conductive
  • Use confirm button
  • Scrape off surface coating for test spot welding
Large spot welding spark
  • Welding pin polluted or oxidized
  • Pressure on workpiece not enough
  • Clean oxide layer on welding pins
  • Increase welding pressure

If the above-mentioned issues cannot be resolved, please contact customer support.

7. Specifications

7.1. Main Machine Parameters (HT-SW01H)

HT-SW01H Product ParametersDimensions and key specifications for the HT-SW01H model.

ParameterSpecificationParameterSpecification
ModelHT-SW01HPeak Power21KW
Peak Current3500APreloading Delay Time100/200/300/400/500ms
Voltage Output5~6VWelding Thickness0.05mm-0.5mm
Peak Welding Energy420JPulse Time0~20ms (100 grade)
Charging Current6ACharging TimeAbout 18 min
Energy Storage Voltage5.2~6.0VNet Weight2KG
Dimensions (LxWxH)67x176x126mm

7.2. Column Type Pneumatic Welding Head (HSW01) Information

Column Type Pneumatic Welding Head Product InformationProduct information for the Column Type Pneumatic Welding Head.

ParameterSpecificationParameterSpecification
Product NameColumn Type Pneumatic Welding HeadAdjustable Column Height Range8-16.5cm
Electrode Maximum Pressure Range6KGPower Supply VoltageAC 110V/220V
Maximum Electrode Travel24mmSize21*27*43.7cm
Weight11.9kg

7.3. Welding Capabilities by Material and Thickness

The following table provides a reference for spot welding various metals using the S-75A Split Spot Welding Pen in MT mode:

MaterialThicknessVoltage RangeEnergy GradeBattery TypeMaterial to be Welded
Aluminum-nickel composite slice0.2mm5.6V-6V40t-50tLithium iron phosphate batteryAluminum electrode
Aluminum-nickel composite slice0.15mm5.6V-6V30t-40tLithium iron phosphate batteryAluminum electrode
Pure nickel0.2mm5.6V-6V45t-55tLithium iron phosphate batteryAluminum electrode
Pure nickel0.15mm5.6V-6V40t-45tLithium iron phosphate batteryAluminum electrode
Pure nickel0.1mm5.0V-5.6V06t-08t18650 batteryNickel/Stainless steel
Pure nickel0.15mm5.0V-5.6V10t-15t18650 batteryNickel/Stainless steel
Pure nickel0.2mm5.0V-5.6V15t-20t18650 batteryNickel/Stainless steel
Nickelage0.1mm5.0V-5.6V05t-08t18650 batteryNickel/Stainless steel
Nickelage0.15mm5.0V-5.6V05t-10t18650 batteryNickel/Stainless steel
Nickelage0.2mm5.0V-5.6V10t-15t18650 batteryNickel/Stainless steel

Please choose the proper energy grade and pulse current according to different object materials and thicknesses.

7.4. NI-NI and AL-NI Welding Mode Comparison

ParametersNI-NI (Nickel to nickel)AL-NI (Aluminum to nickel)
Welding voltage5.6V (MAX)6V (MAX)
Welding current3.2KA (MAX)3.5KA (MAX)
Preloading delayNon-adjustableAdjustable
Reinforce double pulsePreloading delay 500 milliseconds idle state

8. User Tips

  • For optimal energy transfer and better weld quality, ensure welding pins are clean and free of oxidation.
  • When using AT (Automatic Induction) mode, which is faster and more efficient, it is crucial to frequently check the process and quality of solder joints to avoid false welds.
  • If you are new to spot welding or using new materials, start with MT (Foot Trigger) mode to fine-tune parameters before switching to AT mode.
  • Consider watching product demonstration videos to better understand the machine's operation and capabilities.
  • Ensure you have all necessary accessories for your specific welding tasks, as the base kit may require additional components depending on the application.

9. Warranty and Support

Thank you for choosing HeltecBMS products. For optimal user experience, please read this manual carefully. HeltecBMS reserves the right to upgrade the machine and modify the manual without further notice.

For further assistance or inquiries, please contact:

  • Website: www.Heltec-BMS.com
  • E-mail: echo@heltec.cn
  • Tel: 18123313360
  • Address: 64th ChengHong road, Chenghua Section, Chengdu, SiChuan, China

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

© 2023 HeltecBMS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.