Flytec V803

Contents

Flytec V803 RC Bait Boat Circuit Board Set

Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Flytec V803 RC Carp Fishing Bait Boat Circuit Board Set. This set includes both the boat's receiving circuit board and the remote control's transmitting circuit board. Please read this manual thoroughly before use to ensure proper functionality and longevity of your product.

Flytec V803 Circuit Board Set
Figure 1: Flytec V803 Circuit Board Set (Boat Receiving Board, Remote Control Transmitting Board, Display Screen)

Setup

  1. Battery Installation (Boat):
    First, open the battery compartment cover on the boat. Remove the dust plug from the power cord. Install the battery into the compartment and connect it to the power source. Close the battery compartment cover securely.
  2. Antenna Installation (Boat):
    Remove the antenna caps from the boat. Install the two antennas, ensuring they are properly positioned and securely attached.
  3. Power On (Boat):
    Turn on the boat's power switch. The stern lights will flash red and blue alternately, indicating it's ready for pairing.
  4. Pairing the Remote Control:
    At this moment, turn on the power switch of the remote control. Press and hold the power button of the remote control for 3 seconds to turn it on. The boat will automatically perform frequency matching. After successful frequency matching, the front light of the boat will be constantly on, and the blue light of the tail light will be constantly on. The tail lights will remain constantly illuminated in blue, and the headlights will stay on. The signal icon will appear on the remote control.

Note: Do not place the boat on a slope before frequency alignment. Always check whether the left and right motors work properly before launching the boat into water.

Pairing Instructions for V803 Circuit Board Set
Figure 2: Pairing instructions for the V803 circuit board set.
Video 1: Demonstrates the setup and basic operation of the Flytec V803 RC Bait Boat, including battery installation, antenna setup, pairing, light functions, baiting, speed control, and cruise control.

Operating Instructions

  1. Headlight Control:
    The headlights have three modes: constant illumination, flashing, and off. When powered on, they default to constant illumination. Pressing the front headlight button on the remote control cycles through these modes. The headlight icon on the remote control display will also switch accordingly.
  2. Tail Light Control:
    The tail lights also feature three modes: constant illumination, flashing, and off. Upon powering on, they default to constant illumination. Pressing the tail light button on the remote control cycles through these modes. The tail light icon on the remote control display will also transition accordingly.
  3. Baiting Function (Hoppers):
    The remote control allows individual control of the bait hoppers. When the remote control icon for a specific hopper flashes blue, it indicates the open state. The same applies to the other three hoppers. After bait release, the hoppers need to be manually reset (closed).
  4. Speed Control:
    The boat defaults to a single gear speed. Pressing the speed button on the remote control triggers an audible "di di" sound, indicating a switch to the second gear speed.
  5. Cruise Control:
    To activate cruise control, press the cruise control button on the remote control while pushing the remote control stick upward. The boat will then maintain a steady straight course. The boat icon on the remote control display will turn red and flash, with a cruise control icon appearing above it. To cancel cruise control, press the cruise control button again. The cruise control icon will disappear, and the boat icon will revert to its normal color.

Important: Before putting the boat on the water, test it on flat ground to ensure the motor is functioning normally.

Maintenance

  • Cleaning: Regularly clean the circuit boards and connectors with a dry, soft cloth to prevent dust and debris buildup. Ensure no moisture enters the electronic components.
  • Storage: Store the circuit board set in a dry, cool place away from direct sunlight and extreme temperatures. If storing for extended periods, ensure batteries are removed from the boat and remote control.
  • Battery Care: Always use the recommended battery type. Avoid overcharging or completely draining the battery. If the boat or remote control is not used for a long time, charge the battery to about 50% before storing.

Troubleshooting

ProblemPossible CauseSolution
Boat/Remote not pairingIncorrect pairing procedure, low battery, interference.Ensure both devices are powered on and follow the pairing steps precisely. Check battery levels. Move away from potential interference sources.
Motors not respondingLow battery, loose connection, motor malfunction.Check battery charge. Verify all connections to the boat's circuit board are secure. Test motors on flat ground before water launch.
Lights not functioningLoose connection, light mode not selected, component failure.Ensure lights are properly connected to the circuit board. Cycle through light modes using the remote control.
Hoppers not opening/closingMechanical obstruction, remote control signal issue, servo malfunction.Check for any physical obstructions in the hopper mechanism. Ensure remote control is paired and has sufficient battery.

Specifications

FeatureDetail
Brand NameFlytec
Model NumberV803-09/V803-01
MaterialComposite Material
For Vehicle TypeBoats
Remote Control Peripherals/DevicesRECEIVERS
RC Parts & AccsRECEIVERS
OriginMainland China
Recommend Age14+y
UseVehicles & Remote Control Toys
CertificationCE
Is ElectricNo Battery
Is Batteries IncludedNo
Quantity2 (boards)
Boat Circuit Board (V803-09) Net Weight26.3g
Boat Circuit Board (V803-09) Size5.6*6.9*1.3cm
Remote Control Circuit Board (V803-01) Net Weight34.4g
Remote Control Circuit Board (V803-01) Size15.2*4.9*3.1cm
Display Screen Size4.6*3.4*0.2cm
Close-up of Flytec V803 Boat Receiving Circuit Board
Figure 3: Close-up view of the Flytec V803 Boat Receiving Circuit Board.
Flytec V803 Boat Circuit Board (V803-09) with antenna and dimensions
Figure 4: Flytec V803 Boat Circuit Board (V803-09) with antenna, showing net weight (26.3g) and size (5.6*6.9*1.3cm).
Detailed diagram of Flytec V803 Boat Receiving Circuit Board (JR-V803RX) with labeled ports
Figure 5: Detailed diagram of the Flytec V803 Boat Receiving Circuit Board (JR-V803RX) with labeled ports for lights, hoppers, battery, switch, and motors.
Flytec V803 Remote Control Circuit Board with display and dimensions
Figure 6: Flytec V803 Remote Control Circuit Board with display, showing dimensions (15.2*4.9*3.1cm for circuit board, 4.6*3.4*0.2cm for display).
Flytec V803 Remote Control Circuit Board Assembly (V803-01) with display and dimensions
Figure 7: Flytec V803 Remote Control Circuit Board Assembly (V803-01) with display, showing net weight (34.4g) and size (15.2*4.9*3.1cm for circuit board, 4.6*3.4*0.2cm for display).

User Tips

  • Careful Handling: Electronic components are delicate. Always handle the circuit boards with care to avoid damage from static electricity or physical impact.
  • Waterproofing: While the boat is designed for water use, ensure all compartments are properly sealed after battery and antenna installation to prevent water ingress to the electronics.
  • Pre-Launch Check: Always perform a quick function check (motors, lights, hoppers) on dry land before launching the boat into water to prevent unexpected issues.
  • Signal Strength: For optimal performance, ensure a clear line of sight between the remote control and the boat, and avoid operating in areas with high electronic interference.

Warranty and Support

For any issues, warranty claims, or technical support, please contact the Flytec Official Store or the retailer from whom you purchased the product. Keep your proof of purchase for any warranty-related inquiries. Specific warranty terms may vary by region and retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.