DAKEFPV F722 Flight Controller and ESC Stack

Contents

DAKEFPV F722 Flight Controller and ESC Stack User Manual

For 5-inch RC Drone Accessories

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your DAKEFPC F722 Flight Controller and ESC Stack. Designed for high-performance FPV drones, this stack integrates an F722 Flight Controller with a powerful 4-in-1 ESC, supporting various battery configurations and advanced features.

DAKEFPV F722 BLS 8S 70A Stack
Figure 1: DAKEFPC F722 BLS 8S 70A Stack

2. Package Contents

Please verify that all items are present in your package. Contents may vary slightly based on the specific stack option purchased (e.g., FC only, ESC only, or full stack).

Package contents for DAKEFPC F722 70A 30x30 STACK
Figure 2: Package Contents for F722 70A 30x30 Stack (Option 1)

Option 1 - DAKEFPC F722 70A 30x30 STACK includes:

  1. DAKEFPV F722 Flight Controller x 1
  2. DAKEFPV BLS 70A 4 in 1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable* x 1
  10. M3*30mm Inner-hexagon Screws x 5
  11. GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  12. XT60 Power Cable (70mm) x 1

*When the ESC tail faces the drone's front, use this cable for the flight controller and ESC; both ends plug interchangeably.

3. Specifications

The DAKEFPC F722 Flight Controller and ESC stack boasts advanced features for optimal performance.

F722 Flight Controller Specifications:

FeatureSpecification
Product NameDAKE F722 30 x 30 Flight Controller
Main Control Unit (MCU)STM32F722
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENot supported
WIFINot supported
DJI Air Unit ConnectionSupports 6pin plug, two wiring methods
6-pin DJI Air Unit ConnectorFully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no need to change wiring.
FLASH (Black Box)16MB
AmmeterSupported
Input Voltage3-12S LiPo battery
UART Serial Ports8 groups
Buzzer PadSupports BZ+, BZ- pads connected to 5V active buzzer.
BOOT ButtonPress and hold while powering on to force DFU mode for firmware flashing.
RSSI PadSupported, located on the top RS pad.
SmartPort / FPortNot supported
Supported FirmwareBetaFlight (factory default), ArduPilot
Firmware Target NameDAKEFPCVF722
Mounting Hole30.5 x 30.5mm (4mm hole)
Dimensions36 x 36 x 8mm
Weight10.5g

BLS 70A 4-in-1 ESC Specifications:

FeatureSpecification
Product NameDAKE 12S 70A 4 in 1 ESC
FirmwareBLHeli_s/BlueJay
Battery Input3-8S LiPo battery
Continuous Current70A x 4
Max Current80A x 4 (10 seconds)
TVS Anti-Surge DiodeBuilt-in
External Capacitor1000uF high frequency low ESR capacitor (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Output VoltageVBAT
AmmeterSupported (Scale=400, Offset=0)
Current TelemetryNot supported
Mounting Hole30.5 x 30.5mm (4mm hole)
Dimensions45.4 x 42.8 x 6.5mm
Weight23.5g
Dimensions diagram for F722 Flight Controller and ESC
Figure 3: Dimensions of the F722 Flight Controller and ESC

4. Setup and Installation

Careful installation is crucial for the proper functioning and longevity of your FPV stack. Please follow these guidelines.

4.1 Important Stack Installation Note

Important Stack Installation Note
Figure 4: Critical installation considerations

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It is critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated in the diagram. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

4.2 Connecting the Flight Controller and ESC

The FC and ESC can be connected via the provided 8-pin cable or by direct soldering.

BLS 70A 4-in-1 ESC diagram with motor connections
Figure 5: BLS 70A 4-in-1 ESC layout with motor and capacitor connections
Soldering pads definition and cable connections for DJI Air Units
Figure 6: Soldering pads definition and cable connections for various peripherals

4.3 General Wiring Diagram

Refer to the following diagram for connecting various components to your F722 Flight Controller.

General Wiring Diagram for FC, GPS, receiver, VTX, LED
Figure 7: General Wiring Diagram

4.4 Connection with FC & Motors

The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models requiring more than 4 motors.

Supports 8 motors (M1-M8) diagram
Figure 8: Motor connections M1-M8 on the F722 FC
Connection with FC & Motors diagram
Figure 9: Example connection diagram for FC and motors

4.5 DJI Air Unit and Receiver Connections

The F722 Flight Controller is fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Use the 6-pin cable provided with your Air Unit.

DJI Air Unit SBUS signal wire disconnection instruction
Figure 10: Important note for DJI Air Unit SBUS connection

Important Notice for ELRS Receiver:

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Importance Notice for SBUS Receiver:

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

5. Operating Instructions

5.1 Flight Controller Features

More Feature!!! diagram
Figure 11: Overview of F722 Flight Controller features
  • Built-in 16MB Black Box Flash: Continuously records flight status (sensor data, control commands, fault codes). Data can be retrieved for accident analysis even after a crash or power outage.
  • Onboard Barometer: Senses aircraft altitude in real-time.
  • DJI Air Unit Direct Plug Interface: Seamless integration with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
  • Dual Independent BEC: 12V 3A + 5V 3A for stable power to peripherals.
  • 8 Groups of UART Serial Ports: Supports receiver, image transmission, camera, and GPS.
  • USB Power: When powered via USB, it can supply power to the receiver for easy debugging.
  • Reserved Pads: A large number of pads are reserved for enthusiasts for custom connections.

5.2 ESC Features

ESC Upgrade to 70A details
Figure 12: ESC design optimizations for 70A current
  • Upgraded to 70A: Optimized circuit design with copper thickness upgraded from 2 ounces to 3 ounces. MOS tube upgraded for higher specification.
  • High Continuous Current: Continuous current of a single channel is 220A, total of 220A for four channels.
  • High Peak Current: Peak current increased to 280A for 10 seconds.
  • Improved Heat Dissipation: New aluminum alloy heat sink added to quickly dissipate heat from the MOS tube, ensuring more stable electronic speed controller output.
  • TVS Protection Diode: Effectively absorbs voltage spikes caused by power-on or crashes.
  • Advanced Filtering: Onboard 21 high-quality imported Japanese TDK 35V 22uF SMD filter energy storage capacitors, plus a standard 1000uF high-frequency low-resistance electrolytic capacitor, effectively filter out signal interference to the flight controller's gyroscope, making flight smoother.

5.3 LED Light Bar Control

LED light bar pads connection
Figure 13: Connecting to LED light bar pads

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the LED light effect control mode, and short presses of the BOOT button let you toggle between various preset light effects.

5.4 Battery Capacity Indicator

The flight controller features a 4-level battery capacity indicator. Upon connecting the battery, you can instantly see the battery level, eliminating the need for an external LiPo checker.

6. Maintenance

  • Regular Inspection: Periodically check all solder joints and cable connections for any signs of wear, corrosion, or looseness.
  • Cleaning: Keep the flight controller and ESC free from dust, dirt, and moisture. Use a soft brush or compressed air for cleaning. Avoid using liquids directly on the electronics.
  • Firmware Updates: Regularly check for firmware updates for Betaflight/INAV and BLHeli_s/BlueJay. Updating firmware can improve performance, add features, and fix bugs.
  • Capacitor Check: Ensure the Low ESR capacitor is securely connected and shows no signs of damage. This capacitor is vital for protecting against voltage spikes.

7. Troubleshooting

  • No Power/Intermittent Power:
    - Check all power connections, especially the XT60 and the main battery lead. Ensure the Low ESR capacitor is properly installed to prevent voltage spikes.
  • Flight Controller Not Responding:
    - Verify USB connection. If unable to connect, try forcing DFU mode by holding the BOOT button while plugging in USB.
  • Motors Not Spinning/Incorrectly Spinning:
    - Check motor wiring and soldering to the ESC.
  • - Verify motor direction and ESC calibration in Betaflight/INAV configurator.
  • - Ensure the correct ESC protocol (Dshot300/600) is selected.
  • Receiver Issues (ELRS/SBUS):
    - For ELRS, ensure TX/RX are connected to T2/R2. If using with DJI Air Unit, disconnect the SBUS signal wire from the Air Unit harness as described in Section 4.5.
  • - For SBUS, ensure the signal wire is connected to the dedicated SBUS pad on the FC.
  • Video Transmission Issues:
    - Check VTX connections and power supply. Ensure the correct VTX protocol is selected in the FC firmware.
  • LEDs Not Working:
    - Check LED strip connections to the FC pads. Try cycling through LED modes using the BOOT button (short press for modes, long press for control mode).
  • Damage from Improper Installation:
    - As noted in Section 4.1, damage due to incorrect installation (e.g., short circuits from USB interface contact with ESC) is not covered under warranty. Always ensure adequate spacing and proper insulation.

8. User Tips

  • Always use the included Low ESR Capacitor: This is critical for protecting your stack from damaging voltage spikes, especially with higher cell count batteries (6S/8S).
  • Double-check all connections: Before powering up, visually inspect all solder joints and cable connections to prevent shorts or incorrect wiring.
  • Backup your firmware settings: Before making significant changes or updating firmware, always save a backup of your current configuration.
  • Test on a bench first: After assembly and initial setup, perform bench tests (e.g., motor spin tests, receiver checks) before your maiden flight.
  • Keep firmware updated: Regularly check for the latest Betaflight/INAV and BLHeli_s/BlueJay firmware versions to benefit from improvements and bug fixes.

9. Warranty and Support

For warranty claims or technical support, please contact the DAKEFPC RC Factory Store directly through your purchase platform. Be prepared to provide your order details and a clear description of the issue. Please note that damage resulting from improper installation, misuse, or unauthorized modifications may void your warranty.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.