DAKEFPV F405 120A Stack

Contents

DAKEFPV F405 120A Stack Instruction Manual

Model: F405 120A Stack | Brand: DAKEFPV

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your DAKEFPV F405 120A Stack. This high-performance system integrates an F405 Flight Controller and a 120A 4-in-1 Electronic Speed Controller (ESC), designed for FPV freestyle drones and other multi-rotor aircraft requiring robust and reliable control.

The F405 Flight Controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors. It features a built-in 16MB high-speed FLASH for flight data recording and an onboard barometer for real-time altitude sensing.

2. Safety Information

Please read and understand all safety warnings and instructions before using this product. Improper use can lead to damage, injury, or property loss.

  • Always ensure correct polarity when connecting power. Incorrect connections can cause severe damage.
  • Soldering should be performed by experienced individuals. Use appropriate safety gear.
  • Avoid short circuits. Ensure sufficient space between components, especially the FC's USB interface and the ESC.
  • Do not operate the drone in unsafe conditions or near people, animals, or property.
  • Regularly inspect all components for damage before and after each flight.
  • Use only recommended accessories and parts.

3. Package Contents

The DAKEFPV F405 120A Stack package typically includes the following components. Please verify all items are present upon unboxing.

DAKEFPV F405 120A Stack and accessories
Complete DAKEFPV F405 120A Stack with included accessories.
DAKEFPV F405 FC and 12S 120A 4in1 ESC
Individual components: F405 Flight Controller and 12S 120A 4-in-1 ESC.

Option 1 - DAKEFPV F405 120A 30x30 STACK

  • DAKEFPV F405 Flight Controller x 1
  • DAKEFPV BLS 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 silicone O Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable* x 1 (Note: When the ESC tail faces the drone's front, use this cable for FC and ESC; both ends plug interchangeably.)
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6pin cable, Analog VTX 6pin cable, LED/buzzer 4pin cable x 1
  • XT60 Power Cable (70mm) x 1

Option 2 - DAKEFPV F405 30x30 FC (Flight Controller Only)

  • DAKEFPV F405 Flight Controller x 1
  • Silicone Grommets (random colors) x 8
  • Hexagon nuts x 5
  • Silicone rings x 5
  • FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - DAKEFPV 12S 120A 4 in ESC (ESC Only)

  • DAKEFPV 12S 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1

4. Specifications

DAKE F405 30x30 Flight Controller

FeatureDescription
Product NameDAKE F405 30x30 Flight Controller
Main Control Unit (MCU)STM32F405
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENo
WiFiNot supported
DJI Air Unit Connection MethodSupports 6-pin plug-in and soldering methods.
6-pin DJI Sky-side Direct PlugSupports DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no need to change wiring sequence.
FLASH (Black Box)16MB Flash
Current MeterSupported
Input Voltage3-8S LiPo
UART Ports8 groups
Buzzer/LED StripBZ+, BZ- pads connect to 5V powered buzzer.
BOOT ButtonPress BOOT button while powering on to force DFU mode for firmware flashing.
RSSI/Solder PadSupported, top right RSSI pad.
SmartPort/F.PortNot supported
Supported Firmware TypesBetaFlight (default firmware), Ardupilot
Firmware Target NameDAKEFPVF405
Mounting Hole Size30.5 x 30.5 mm (4mm holes)
Dimensions36 x 36 x 8 mm
Weight10.5g

DAKE 12S 120A 4 in 1 ESC

FeatureDescription
Product NameDAKE 12S 120A 4 in 1 ESC
FirmwareBLHeli_S / BLHELI_Jay
Input Voltage3-12S LiPo
Continuous Current120A x 4
Maximum Current125A x 4 - 10S
Built-in TVS DiodeYes
External Capacitor1000uF Low ESR Capacitor (included in package)
ESC ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot.
Input Voltage3-12S LiPo
Output VoltageVBAT
Current MeterSupported (Scale=400, Offset=0)
Temperature SensorNot supported
Mounting Hole Size30.5 x 30.5 mm (4mm holes)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g

General Dimensions

Dimensions of F405 Flight Controller and 120A 4-in-1 ESC
Detailed dimensions for the F405 Flight Controller (36x36mm, 30.5x30.5mm mounting) and the 120A 4-in-1 ESC (60x55mm, 30.5x30.5mm mounting). Total stack height is 15.8mm.

5. Setup and Installation

5.1 Important Stack Installation Note

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated below. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

Stack installation note showing proper spacing between FC and ESC
Ensure sufficient space between the FC and ESC, especially if mounting inverted, to prevent short circuits.

5.2 Wiring Diagram

Refer to the following diagram for general wiring connections. This diagram illustrates connections for motors, receiver, GPS, VTX, and LED strips.

Comprehensive wiring diagram for DAKEFPV F405 stack
Detailed wiring diagram showing connections for FC, ESC, motors, receiver, GPS, VTX, and LED.

5.3 Flight Controller Layout

F405 Flight Controller layout with pin descriptions
F405 Flight Controller layout showing pin assignments for OSD, RX3, M6-M1, BAT, GND, CUR, CAM1, CAM2, 5V, 12V, DP, DM, LED, 3V3, CLK, DIO, R1, T1, SDA, SCL, ELRS, Gyro (ICM42688P, MPU85001), VTX, GPS, DJI, USB, VTX(Analog), DIY, PINIO1, Buzzer LED strip Galvanometer.

The flight controller supports 8 motors, so it can be used on X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors. Connections for M1-M6 are highlighted.

F405 Flight Controller motor output diagram
F405 Flight Controller motor output diagram for M1-M6.

5.4 ESC Layout

BLS 120A 4-in-1 ESC layout with motor connections
BLS 120A 4-in-1 ESC layout showing MOTOR 1-4 connections, BAT+ and GND pads, and capacitor pin holes.

5.5 Receiver Connections

5.5.1 SBUS Receiver Connection

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

SBUS receiver wiring diagram with DJI Air Unit warning
SBUS receiver connection diagram, highlighting the need to disconnect the SBUS wire from the DJI Air Unit harness if using an external SBUS receiver.

5.5.2 ELRS Receiver Connection

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

ELRS receiver wiring diagram with DJI Air Unit warning
ELRS receiver connection diagram, showing connection to T2/R2 pads and a warning about disconnecting the SBUS wire from the DJI Air Unit if issues arise.

5.6 DJI Air Unit Connections

5.6.1 Cable Connection vs DJI O3 Air Unit

Use the 6-pin cable that comes with the O3 Air Unit for connection.

Cable connection for DJI O3 Air Unit
Diagram showing the connection of the F405 FC to a DJI O3 Air Unit using the provided 6-pin cable.

Use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in the package section).

Cable connection for RunCam Link/Caddx Vista Air Unit
Diagram showing the connection of the F405 FC to a RunCam Link or Caddx Vista Air Unit using the specified 6-pin cable.

5.7 Low ESR Capacitor Installation

In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package.

The ESC is equipped with a TVS protection diode, 21 imported Japanese TDK SMD filter capacitors, and a 1000uF ultra-large capacity capacitor. This combination effectively absorbs voltage spikes and filters signal interference from the power supply to the flight controller's gyroscope, resulting in smoother flight.

Low ESR capacitor and filter components on ESC
Illustration of the TVS diode, SMD filter capacitors, and the 1000uF Low ESR capacitor on the ESC for surge protection and filtering.

6. Operating Instructions

6.1 Powering On and Battery Level Indicator

On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on glasses to check the battery status.

Battery level indicator on F405 Flight Controller
The F405 FC features a 4-level battery capacity indicator (FCC, 3V, 5V, 12V) for quick visual battery status checks.

6.2 LED Light Bar Control

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode. Short presses then toggle between various preset light effects.

LED light bar connection and control via BOOT button
Diagram showing LED pads on the FC and how the BOOT button controls LED lighting modes and effects.

6.3 Firmware Flashing (DFU Mode)

To flash new firmware or troubleshoot issues, you can enter DFU (Device Firmware Upgrade) mode. Press and hold the BOOT button while powering on the flight controller to force it into DFU mode.

6.4 Onboard Barometer and Black Box

The onboard barometer senses the aircraft's altitude in real-time. The built-in 16MB high-speed FLASH continuously records flight status (sensor data, control commands, fault codes). In the event of a crash or power outage, this data can still be retrieved for accident analysis.

F405 Flight Controller with built-in 16MB FLASH for black box recording
The F405 FC features a built-in 16MB FLASH memory for black box flight data recording.

7. Maintenance

  • Regular Inspection: Periodically check all solder joints and connections for looseness or corrosion.
  • Cleaning: Keep the flight controller and ESC free from dust, dirt, and moisture. Use a soft brush or compressed air for cleaning.
  • Firmware Updates: Regularly check for and apply firmware updates for BetaFlight/Ardupilot to ensure optimal performance and access to new features.
  • Capacitor Check: Ensure the Low ESR capacitor is securely attached and shows no signs of damage.

8. Troubleshooting

  • No Power:
    • Check battery connection and polarity.
    • Inspect power cables for damage.
    • Ensure the main power lead is properly soldered to the ESC.
  • Motors Not Spinning/Erratic Behavior:
    • Verify ESC to motor connections.
    • Check motor direction in BetaFlight/ESC configurator.
    • Ensure ESC firmware is compatible and properly configured (e.g., Dshot protocol).
    • Recalibrate ESCs if necessary.
  • Receiver Not Detected:
    • Double-check receiver wiring to the correct UART pads (e.g., SBUS to SBUS pad, ELRS to T2/R2).
    • If using DJI Air Unit, ensure the SBUS signal wire from the Air Unit harness is disconnected if using an external SBUS or ELRS receiver.
    • Verify receiver protocol is correctly set in BetaFlight.
  • Flight Controller Not Connecting to PC:
    • Ensure USB cable is functional and connected securely.
    • Try a different USB port or cable.
    • Install necessary drivers (e.g., STM32 Virtual COM Port Driver, Zadig for DFU mode).
    • Try entering DFU mode (hold BOOT button while plugging in USB).
  • Excessive Vibrations/Unstable Flight:
    • Check for loose propellers or motors.
    • Ensure FC is soft-mounted correctly with silicone grommets.
    • Verify gyro orientation in BetaFlight.
    • Check for bent motor shafts or damaged bearings.
  • Voltage Spikes/Burnout:
    • Ensure the Low ESR capacitor is installed correctly on the ESC power pads.
    • Avoid powering up with loose connections.

9. User Tips

  • Soft Mounting is Key: Always use the provided silicone grommets for soft mounting the FC to minimize vibrations and improve flight performance.
  • Capacitor is Crucial: Do not skip installing the Low ESR capacitor. It significantly protects your ESC and FC from voltage spikes, especially with higher cell count batteries.
  • Clean Soldering: Good soldering practices are essential for reliability. Ensure strong, clean joints and avoid solder bridges.
  • BetaFlight Configuration: Take time to properly configure BetaFlight. Use the latest stable firmware and tune your PIDs for optimal flight characteristics.
  • Wiring Management: Keep wiring neat and secure to prevent interference and accidental disconnections during flight.

10. Warranty and Support

This product is covered by a limited warranty against manufacturing defects. Please refer to the seller's terms and conditions for specific warranty duration and coverage details.

Note: Damage resulting from improper installation, such as short circuits due to insufficient spacing between the FC's USB interface and the ESC, is not covered under warranty.

For technical support, firmware updates, or further assistance, please contact DAKEFPV Model Store directly through their official channels or the platform where the product was purchased.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.