JIKONG 7 INCH Display V19

Contents

JIKONG 7-inch Display Screen for PB Series JKBMS

Model: 7 INCH Display V19 (LCD-7.0-TTL-P)

1. Introduction

This manual provides detailed instructions for the operation and maintenance of the JIKONG 7-inch Display Screen, specifically designed for JIKONG PB Series JKBMS (V19 version). This display offers a clear interface for monitoring and managing your battery system.

JIKONG 7-inch Display Screen showing main interface with voltage, current, and battery capacity

Figure 1: JIKONG 7-inch Display Screen Main Interface

2. Product Features

  • Wide Power Supply: Supports a working range of 9V to 36V.
  • Comprehensive Display: Shows battery total voltage, battery power, and single series voltage.
  • Communication: Supports TTL/CMOS levels with a maximum baud rate of 921600bps.
  • Multi-language Support: Chinese, English, Thai, and Vietnamese switchover is supported.
  • Customization: Allows for language, logo, and interface customization.

3. Specifications

Table 1: General Specifications
ParameterValue
Display CategoryTFT
Display Size7-inch
Resolution1024 * 600
Backlight Type/BrightnessLED / 200 cd/m²
Viewing Angle (L/R/U/D)60°/60°/50°/40°
Operating Temperature-10°C to +60°C
Storage Temperature-20°C to +70°C
Operating Humidity10% to 90% RH (at 25°C)
Supply Voltage (with reverse protection)9V to 36V
Power Dissipation2.7W (12V@225mA)

3.1. Product Dimensions

Diagram showing the dimensions of the 7-inch display screen

Figure 2: Display Screen Dimensions (Units in mm)

  • Lens Outer Dimensions: 187.00mm (width) x 120.00mm (height)
  • LCD Active Area/Viewing Area: 154.08mm (width) x 85.92mm (height)

4. Package Contents

The product package typically includes:

  • 1 x JIKONG 7-inch Display Screen
  • 1 x Connection Cable (standard length 0.5 meters, customizable)
JIKONG 7-inch touch screen display with its connection cable

Figure 3: Display Screen and Connection Cable

5. Setup and Connection

5.1. External Interfaces

The display screen features several interfaces for power, communication, and control:

Diagram showing the back of the display with labeled connectors for user interface, key extension, and TF card

Figure 4: External Interfaces of the Display Screen

  • User Interface: Used for power supply and serial port signal connection. Socket type: HY2.0mm-6P vertical stick.
  • Key Extension Interface: Used to control BMS startup and shutdown. Socket type: GH1.25-6P vertical sticker.
  • TF Card Interface: Connects a TF card for offline download and interface translation.

5.2. Pin Definitions

Table 2: User Interface Pin Definitions
NumberNameDefinition
1K-Activation signal negative electrode
2K+Activate the positive signal
3GNDGround
4TXDSerial Port Output
5RXDSerial Port Input
6VINPower Supply
Table 3: Key Extension Interface Pin Definitions
NumberNameDefinition
1K-Activation signal negative electrode
2K+Activate the positive signal
3GNDGround
4TXDSerial Port Output
5RXDSerial Port Input
6VINPower Supply
JIKONG V19 7-inch Touch Screen Display connected to a JIKONG V19 PB Serial BMS via UART connector

Figure 5: Display connected to JIKONG V19 PB Serial BMS

6. Operating Instructions

6.1. APP Operation Instructions

To configure the display via the JIKONG BMS APP:

  1. Open the JIKONG BMS APP.
  2. Navigate to the "Parameter Setting" page.
  3. Change the "Serial port 3 protocol" to "015-JK BMS PBxx SERIES LCD Protocol V1.0".
Screenshots of the JIKONG BMS APP interface showing protocol selection

Figure 6: JIKONG BMS APP Protocol Selection Interface

6.2. Display Interface Operation

6.2.1. Battery Interface

The battery interface displays real-time information about your battery string:

  • Current voltage and current of the battery string.
  • Number of online battery packs.
  • Charging and discharging status of the entire battery string.
  • Highest and lowest cell temperature.
JIKONG 7-inch display showing the main battery interface with voltage, current, capacity, and cell details

Figure 7: Battery Interface Display

6.2.2. Battery Pack Interface

In parallel mode, you can select individual battery packs to view detailed information:

  • Design capacity and remaining capacity.
  • Charging and discharging status of each battery pack.
  • Voltage of each cell.
  • Supports display for up to 16 battery packs.
JIKONG 7-inch display showing detailed information for individual battery cells within a pack

Figure 8: Battery Pack Information Display

6.2.3. Protocol Selection Interface

This interface allows you to select the appropriate 485 and CAN communication protocols for your BMS system.

JIKONG 7-inch display showing the protocol selection interface for RS485 and CAN protocols

Figure 9: Protocol Selection Interface

6.2.4. Fault Alarm Interface

When a fault occurs, the alarm icon will light up, and a number indicating the fault code will be displayed. Refer to the table below for fault code descriptions.

Table 4: Fault Code Descriptions
Fault CodeAlarm Description
1Single cell undervoltage alarm (Over-discharge Protection)
2Single cell overvoltage alarm (Over-charge Protection)
3Overcurrent alarm
4MOS overtemperature alarm
5Battery overtemperature alarm
6Short circuit alarm
7Internal communication failure alarm
8Balancing line resistance too high alarm
9Cell string loss

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the display screen. Avoid using abrasive cleaners or solvents that may damage the screen surface.
  • Environmental Conditions: Ensure the display operates within the specified temperature and humidity ranges to prevent damage.
  • Cable Inspection: Periodically check the connection cable for any signs of wear, damage, or loose connections.

8. Troubleshooting

  • Display Not Powering On: Verify that the power supply voltage is within the 9-36V range and that the power connections are secure.
  • No Data Displayed: Check the serial port connection to the BMS. Ensure the correct communication protocol is selected in the JIKONG BMS APP (015-JK BMS PBxx SERIES LCD Protocol V1.0).
  • Incorrect Readings: If readings appear inaccurate, ensure all connections are correct and secure. Refer to the fault alarm interface for any active error codes.
  • Screen Damage: Handle the display with care. Avoid dropping or applying excessive pressure to the screen.

9. User Tips

  • Connection Verification: Always use a multimeter to verify wire connections, especially for power and communication lines, before applying power to the system. This can prevent issues like crossed wires.
  • Readability: If the percentage display or other text appears too small, check if there are any customization options in the APP or display settings to adjust font sizes for better readability.

10. Warranty and Support

For warranty claims, technical support, or further assistance, please contact JIKONG Official Store directly. Keep your purchase records for reference.

11. Product Video

Video: Overview of JIKONG BMS products and manufacturing process.

12. Additional Resources

A detailed user manual in PDF format is available for download. This document provides comprehensive guides and specifications for the JIKONG 7-inch display screen.

Reference: User manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.