DAKEFPV F722 60A Stack

Contents

DAKEFPV F722 60A Stack Flight Controller and 4in1 ESC Instruction Manual

Model: F722 60A Stack

Brand: DAKEFPV

1. Introduction

Thank you for choosing the DAKEFPV F722 60A Stack, a high-performance flight controller (FC) and 4-in-1 Electronic Speed Controller (ESC) solution designed for FPV freestyle drones and other multi-rotor aircraft. This stack combines advanced features, robust power delivery, and a compact design to provide an exceptional flying experience. This manual will guide you through the installation, setup, and operation of your new DAKEFPV F722 60A Stack.

DAKEFPV F722 Flight Controller and 70A 4in1 ESC stack components
Figure 1: DAKEFPV F722 Flight Controller and 70A 4in1 ESC stack components.

2. Package Contents

Please check the contents of your package carefully. The exact items may vary slightly depending on the purchased option (Stack, FC only, or ESC only).

Option 1: DAKEFPV F722 70A 30x30 STACK

  • DAKEFPV F722 Flight Controller x 1
  • DAKEFPV BLS 70A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 silicone O Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable* x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  • XT60 Power Cable (70mm) x 1

*Note: When the ESC tail faces the drone's front, use this cable for the flight controller and ESC; both ends plug interchangeably.

Option 2: DAKEFPV F722 70A 30x30 FC (Flight Controller only)

  • DAKEFPV F722 Flight Controller x 1
  • Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
  • FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3: DAKEFPV 8S 70A 4 in 1 ESC (ESC only)

  • DAKEFPV 8S 70A 4 in 1 ESC x 1
  • 35v1000uf Low ESR Capacitor (Buy 12S ESC Send 63V1000uf Capacitor)
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1
DAKEFPV F722 FC + 8S 70A 4in1 ESC package contents
Figure 2: Example package contents for the F722 FC + 8S 70A 4in1 ESC stack.
Package contents for Option 2 (F722 FC) and Option 3 (8S 70A 4in1 ESC)
Figure 3: Package contents for Flight Controller only (Option 2) and ESC only (Option 3).

3. Specifications

DAKE F722 30x30 Flight Controller

Feature Specification
Product NameDAKE F722 30x30 Flight Controller
Main ControlSTM32F722
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENo
WIFINot supported
DJI Air Unit Connection MethodSupports 6-pin plug, two soldering methods
6-pin DJI Air Unit Direct Plug SocketSupported (Compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1)
FLASH (Black Box)16MB memory
AmmeterSupported
Input Voltage3-12S LiPo battery
UART Serial Port8 groups
Buzzer PadSupported (BZ+, BZ- pads for active buzzer)
BOOT ButtonPress and power on simultaneously for DFU mode
RSS PadSupported (Front top of OSD pad)
SmartPort / FPortNot supported
Supported FC FirmwareBetaFlight (default), Ardupilot
Firmware Target NameDAKEFPVF722
Mounting Hole30.5 x 30.5mm (4mm hole diameter)
Size36 x 36 x 8 mm
Weight10.5g
Specifications table for DAKEFPV F722 30x30 Flight Controller (part 1)
Figure 4: DAKE F722 Flight Controller Specifications (Part 1).

DAKE12S 70A 4 in 1 ESC

Feature Specification
Product NameDAKE12S 70A 4 in 1 ESC
FirmwareBLHeli_S / BlueJay
Battery Input3-8S LiPo battery
Continuous Current70A x 4
Maximum Current80A x 4 - 10S
Built-in TVS Transient Suppression DiodeYes
External Capacitor1000uF high frequency low resistance capacitor (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Input Voltage3-8S LiPo battery
Output VoltageVBAT
AmmeterSupported (Scale=400, Offset=0)
Current DetectionNot supported
Mounting Hole30.5 x 30.5mm (4mm hole diameter)
Size45.4 * 42.8 * 6.5mm
Weight23.5g
Specifications table for DAKEFPV F722 Flight Controller and DAKE12S 70A 4 in 1 ESC (part 2)
Figure 5: DAKE F722 Flight Controller and DAKE12S 70A 4 in 1 ESC Specifications (Part 2).

Key Features

  • Supports BetaFlight and Ardupilot firmware.
  • Built-in 16MB high-speed FLASH for black box logging.
  • Onboard barometer for real-time altitude sensing.
  • DJI Air Unit direct plug interface for O3/Vista/Air Unit V1.
  • Dual independent BECs: 12V 3A and 5V 3A.
  • Ample 8 groups of idle serial ports (UARTs).
  • Supports receiver, image transmission, camera, and GPS.
  • Power to receiver via USB for easy debugging.
  • Numerous reserved pads for customization.
  • Supports 8 motors for X8/Y6/fixed-wing aircraft.
  • ESC upgraded to 70A continuous current with optimized circuit design and aluminum heat sink.
  • Integrated TVS protection diode and 21 imported Japanese TDK SMD filter capacitors for surge protection and smooth flight.
  • 4-level battery capacity indicator on the FC.
Overview of additional features including Barometer, Black box Flash, BEC, UARTs, GPS module power, and reserved pads
Figure 6: Overview of additional features.
Description of the ESC upgrade to 70A, including PCB copper thickness and heat sink
Figure 7: ESC Upgrade to 70A details.
Details on TVS diode and filter capacitors for surge protection and signal filtering
Figure 8: TVS diode and filter capacitors for enhanced protection.
Feature highlighting the 4-level battery capacity indicator on the FC
Figure 9: 4-level battery capacity indicator on the Flight Controller.

4. Installation

4.1 Pre-Installation Notes

  • Always use the provided Low ESR capacitor to prevent voltage spikes when powering up, which can damage the stack.
  • Adhere to the standard mounting method. The orientation of the gyroscope and motor sequence can be adjusted through software settings.
  • If opting for an inverted mounting, ensure sufficient space between the frame, the FC, and the ESC to prevent contact.
  • It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Damage from improper installation is not covered under warranty.
Important Stack Installation Note regarding orientation and silicon pads
Figure 10: Important Stack Installation Note.
Wiring Diagram illustrating the recommended space between FC and ESC in the stack
Figure 11: Recommended spacing in the stack assembly.

4.2 Physical Installation

  1. Mount the ESC: Secure the 4-in-1 ESC to your drone frame using the provided M3*30mm screws and M3*8.1mm silicone grommets.
  2. Mount the Flight Controller: Place the F722 Flight Controller on top of the ESC, aligning the mounting holes. Use the M3*8mm silicone grommets for the FC. Ensure the USB port is accessible and facing a convenient direction.
  3. Secure the Stack: Use the M3 nylon nuts to secure the FC to the ESC, forming a stable stack.
Dimensional drawings of the F722 Flight Controller and ESC, including stack height
Figure 12: Dimensions of the Flight Controller and ESC.

4.3 Wiring Connections

Refer to the detailed wiring diagrams below for connecting your motors, receiver, VTX, camera, GPS, and other peripherals.

Comprehensive wiring diagram for connecting the FC and motors, along with various peripherals
Figure 13: Comprehensive Wiring Diagram for FC and Peripherals.
Detailed wiring diagram for the F722 FC, showing connections for various components like LED, USB, GPS, ELRS, VTX, and camera
Figure 14: Detailed F722 FC Wiring Diagram.
Layout of the BLS 70A 4-in-1 ESC, indicating motor connections and capacitor pins
Figure 15: BLS 70A 4-in-1 ESC Layout.

4.3.1 FC-ESC Connection

  • Use the provided SH 1.0mm 8pin cable to connect the FC and ESC.
  • Alternatively, direct soldering is possible. Refer to Figure 16 for soldering pad definitions.
Instructions for connecting the FC and ESC via direct soldering and cable connection with DJI O3 Air Unit
Figure 16: FC-ESC Direct Soldering and DJI O3 Air Unit Connection.

4.3.2 DJI Air Unit Connection

  • The FC supports direct plug-in for DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 using the 6-pin cable.
  • Refer to Figure 16 and Figure 17 for connection details.
Connection instructions for RunCam Link/Caddx Vista Air Unit and DJI Air Unit V1 using the H743 stack cable
Figure 17: Air Unit Connection Options.

4.3.3 Receiver Connection (SBUS & ELRS)

  • SBUS Receiver: Connect the SBUS signal wire of the receiver to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If you are also using a DJI Air Unit (O3/Link/Vista/Air Unit V1), you MUST disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. Use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
  • ELRS Receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. Use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
Important notices for SBUS and ELRS receiver connections, including a diagram showing incorrect SBUS connection
Figure 18: SBUS and ELRS Receiver Connection Notes.

4.3.4 LED Light Bar Connection

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses toggle between various preset light effects.

Diagram showing LED light bar pad connections on the F722 FC
Figure 19: LED Light Bar Pad Connections.

4.3.5 General Layouts

Top and bottom layout diagrams of the F722 Flight Controller, detailing ports and components
Figure 20: F722 Flight Controller Top and Bottom Layout.

5. Operating Instructions

5.1 Firmware Flashing

To flash new firmware (e.g., BetaFlight or Ardupilot), connect the FC to your computer via the Type-C USB port. If the FC is not recognized, press and hold the BOOT button while connecting power to force DFU mode. Use the appropriate configurator software (e.g., BetaFlight Configurator) to flash the DAKEFPVF722 target firmware.

5.2 Battery Level Indicator

The F722 Flight Controller features a convenient 4-level battery capacity indicator. Simply connect your LiPo battery to the stack, and the indicator will instantly display the current battery level, eliminating the need for an external LiPo checker.

5.3 Motor Support

The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors.

Diagram showing support for 8 motors (M1-M8) on the F722 FC
Figure 21: F722 FC Motor Support (M1-M8).

6. Maintenance

  • Keep the stack clean and free from dust and debris. Use compressed air or a soft brush for cleaning.
  • Regularly inspect all solder joints and connections for any signs of damage or corrosion.
  • Ensure proper airflow around the ESC to prevent overheating, especially during aggressive flying.
  • Periodically check for firmware updates for both the FC (BetaFlight/Ardupilot) and ESC (BLHeli_S/BlueJay) to ensure optimal performance and access to new features.

7. Troubleshooting

Common Issues and Solutions:

  • FC not recognized by computer: Try pressing and holding the BOOT button while connecting the USB cable to force DFU mode. Ensure you have the correct drivers installed.
  • Motors not spinning/incorrect direction: Check motor wiring and configuration in your flight controller software (e.g., BetaFlight). Ensure ESC firmware is up to date and calibrated.
  • Intermittent receiver connection (SBUS/ELRS with DJI Air Unit): As noted in Section 4.3.3, ensure the SBUS signal wire from the DJI Air Unit harness is disconnected if using an external SBUS or ELRS receiver.
  • Sudden power loss/burnout: Always use the provided Low ESR capacitor to filter voltage spikes. Inspect for short circuits due to improper installation (e.g., USB port contacting ESC).
  • Unstable flight: Verify all connections are secure. Check for proper gyro orientation and calibration in the flight controller software. Ensure propellers are balanced and undamaged.

8. User Tips

No specific user tips from reviews or Q&A were available for this product. However, general best practices for FPV electronics include:

  • Always double-check wiring before applying power to prevent damage.
  • Use heat shrink tubing or electrical tape to insulate exposed solder joints and wires.
  • Perform a smoke stopper test before connecting a battery for the first time after assembly or major repairs.
  • Keep your firmware updated for the best performance and bug fixes.
  • Calibrate your ESCs and sensors regularly.

9. Warranty and Support

DAKEFPV products are designed for high performance and reliability. Please refer to the seller's terms and conditions for specific warranty details. Damage resulting from improper installation, misuse, or unauthorized modifications may void your warranty.

For technical support, firmware updates, or further assistance, please contact your retailer or visit the official DAKEFPV support channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.