1. Introduction
Thank you for choosing the EDON TIG-200 PULSE ACDC Inverter Welding Machine. This versatile welding unit is designed for high-performance TIG and MMA welding across a variety of metals, including stainless steel, alloy steel, carbon steel, brass, other nonferrous metals, and especially aluminum. Featuring advanced high-frequency inverter technology and square-wave output, it ensures stable and efficient welding. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to help you achieve optimal welding results.

A general view of the EDON TIG-200 PULSE ACDC welding machine, showcasing its compact design and front panel.
2. Safety Precautions
Always prioritize safety when operating welding equipment. Failure to follow safety guidelines can result in serious injury or death.
- Electric Shock: Welding current can cause fatal electric shock. Ensure proper grounding and insulation. Never touch live electrical parts.
- Fumes and Gases: Welding produces fumes and gases that can be hazardous to health. Work in a well-ventilated area or use local exhaust ventilation.
- Arc Rays: Arc rays can burn eyes and skin. Always wear a welding helmet with appropriate shade, safety glasses, and protective clothing.
- Fire and Explosion: Welding sparks and hot metal can cause fires or explosions. Keep flammable materials away from the welding area. Have a fire extinguisher readily available.
- Burns: Hot metal and sparks can cause severe burns. Wear protective gloves and clothing.
- Noise: Excessive noise can damage hearing. Wear ear protection.
3. Product Components and Accessories
The EDON TIG-200 PULSE ACDC welding machine comes with the following standard accessories:

Image showing the standard accessories: TIG torch, ground clamp, electrode holder, gas hose, welding mask, and wire brush.
- TIG Torch
- Ground Clamp
- Electrode Holder
- Gas Hose
- Welding Mask
- Wire Brush
The main unit features a robust design with a digital display and intuitive controls for various welding parameters.

Diagram illustrating the dimensions of the welding machine: 280mm height, 425mm length, and 160mm width.
4. Technical Specifications

A table detailing the technical specifications of the welding machine.
| Parameter | Value |
|---|---|
| Input Voltage | 1PH 110/220V±15%, 50/60Hz |
| Input Current | 24.1 A |
| Output Power Capacity | 4.5 KVA |
| Output Current Range | TIG: 10-200 A / MMA: 20-180 A |
| Arc Force Current | 0-100 A |
| Pre-flow Time | 0-2 seconds |
| AC Output Frequency | 60 Hz |
| Clean Width | 20-80% |
| Down-slope Time | 0-10 seconds |
| Post-flow Time | 0-10 seconds |
| Base Current | 10-90% |
| Pulse Frequency | 0.5-300 Hz |
| Pulse Duty Cycle | 10-90% |
| Arc-leading Method | HF Vibration |
| Rated Duty Cycle @40°C (TIG) | 60% |
| Efficiency | 85% |
| Power Factor | 0.73 |
| Dimensions (L x W x H) | 425 x 160 x 280 mm |
| Weight | 8.5 KG |
| Material / Metal Processed | Carbon Steel, Stainless Steel, Aluminum Alloy, Brass, other nonferrous metals |
| Output Polarity | AC/DC TIG |
| Condition | New |
| Warranty | 1 Year |
5. Setup Instructions
Follow these steps to set up your welding machine:
- Placement: Place the welding machine on a stable, level surface in a well-ventilated area, away from flammable materials.
- Power Connection: Ensure the main power switch on the rear panel is OFF. Connect the power cord to a suitable 110V or 220V AC power outlet, ensuring it matches the machine's input voltage.
- Gas Connection (for TIG welding):

The rear panel showing the main power switch, AC 220V input, cooling fans, and gas inlet connection.
Connect the gas hose from your inert gas cylinder (e.g., Argon) to the GAS inlet connector on the rear panel of the machine. Secure all connections to prevent leaks.
- TIG Torch Connection: Connect the TIG torch cable to the appropriate connector on the front panel. Ensure it is securely fastened.
- Ground Clamp Connection: Connect the ground clamp cable to the negative (-) terminal on the front panel for DC TIG/MMA, or to the appropriate terminal for AC TIG. Attach the ground clamp securely to the workpiece, ensuring good electrical contact.
- Electrode Holder Connection (for MMA welding): If performing MMA welding, connect the electrode holder cable to the positive (+) terminal on the front panel.
- Foot Pedal Connection (Optional): If using a foot pedal for current control, connect it to the designated port on the front panel.
6. Operating Instructions
Familiarize yourself with the control panel before operation.

A diagram of the control panel with numbered labels: 1. TIG-MMA mode selection, 2. AC-DC mode selection, 3. PULSE ON/OFF, 4. 2T-4T trigger mode, 5. Digital Display Meter.
- Power On: Turn on the main power switch on the rear panel. The digital display (5) will illuminate.
- Select Welding Mode (1): Use the TIG-MMA button to switch between TIG and MMA welding modes.
- Select Current Type (2): Use the AC-DC button to select AC (for aluminum) or DC (for stainless steel, carbon steel, etc.) current type.
- Pulse Function (3): Press the PULSE ON/OFF button to activate or deactivate the pulse welding function. Adjust pulse parameters using the main control knob.
- Trigger Mode (4): Select between 2T (2-Touch) or 4T (4-Touch) trigger mode using the 2T-4T button.
- 2T Mode: Press and hold the torch trigger to start welding; release to stop.
- 4T Mode: Press and release the trigger to start welding; press and release again to stop. This mode is useful for longer welds to reduce hand fatigue.
- Adjust Parameters: Use the large rotary knob to adjust welding parameters such as current (Amps), pre-flow time, AC output frequency, clean width, down-slope time, post-flow time, base current, and pulse frequency/duty cycle, as indicated on the display (5) and the graphical interface.
- Begin Welding: Once all parameters are set, put on your welding helmet and protective gear, and begin welding according to standard welding practices for your chosen material and process.

Visual examples of fillet welding results. For stainless steel: 120A welding current, 1.2mm welding wire, 4mm plate thickness. For aluminum: 120A welding current, 2.4mm welding wire, 5mm plate thickness.
A short video demonstrating the physical aspects of the welding machine, including its weight (8.5 KG), new condition, AC/DC TIG output polarity, and suitability for aluminum welding.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Regularly clean the machine's exterior with a dry cloth. Use compressed air to blow out dust and debris from the ventilation openings. Ensure the machine is unplugged before cleaning.
- Cable Inspection: Periodically inspect all cables (power, torch, ground) for damage, cuts, or frayed insulation. Replace damaged cables immediately.
- Connections: Check all electrical and gas connections for tightness and corrosion.
- Storage: Store the machine in a clean, dry environment, away from excessive dust, moisture, and extreme temperatures.
- Fan Operation: Ensure the cooling fans on the rear panel are free from obstructions and operating correctly.
8. Troubleshooting
This section addresses common issues you might encounter. For more complex problems, contact customer support.
- No Power: Check the power cord connection, main power switch, and circuit breaker. Ensure the input voltage matches the machine's requirements.
- No Arc: Verify all connections (ground clamp, torch, electrode). Ensure the workpiece is clean and has good electrical contact. Check welding parameters.
- Poor Weld Quality: Adjust welding current, gas flow, and travel speed. Ensure proper electrode type and size for the material. Check for gas leaks or contaminated shielding gas.
- Overheating: The machine has O.C.&O.H protection. If it overheats, it will shut down. Allow it to cool down. Ensure ventilation is not obstructed and the duty cycle is not exceeded.
- Gas Flow Issues: Check gas cylinder pressure, regulator settings, and hose connections for leaks.
9. User Tips
- Always ensure proper ventilation to avoid inhaling welding fumes.
- For TIG welding, maintain a consistent arc length and torch angle for optimal results.
- Practice on scrap material to fine-tune your settings before working on your main project.
- Keep your tungsten electrode sharp and clean for a stable arc.
- When welding aluminum, ensure the AC balance and frequency are correctly set for effective cleaning action and penetration.
10. Warranty and Support
The EDON TIG-200 PULSE ACDC Inverter Welding Machine comes with a 1-Year Warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
For technical support, service, or warranty inquiries, please contact your retailer or the manufacturer's authorized service center. Do not attempt to repair the machine yourself, as this may void the warranty and pose safety risks.