1. Introduction
This manual provides detailed instructions for the MIBOXER C8 8-Zone RGB+CCT Remote and C9 SPI Remote. These 2.4GHz RF wireless remote controls are designed for adjusting RGB, brightness, color temperature, and saturation of compatible LED lamps and strips. Please read this manual carefully before use to ensure proper operation and to extend the product's lifespan.
2. Key Features
- 2.4GHz RF Wireless Technology: Ensures fast transmission, stable signal, and strong anti-interference capabilities.
- Control Distance: Up to 30 meters.
- Material: Durable ABS construction.
- High-Precision Touching IC: Provides stable and sensitive touch control.
- Working Voltage: 3V (requires 2 x AAA batteries, not included).
- Working Temperature: -10°C to 40°C.
- Transmitting Power: 6dBm.
- Modulation Method: GFSK.
- Certifications: CCC, CE, ROHS, SAA (C8); CE, EMC, RED (C9).
C8 (8-Zone RGB+CCT Remote) Specific Features:
- Controls 8 independent zones, each capable of controlling countless bulbs.
- Compatible with MiBoxer/Mi-Light 2.4G series products.
- Adjustable RGB color, brightness, color temperature, and saturation.
- Includes a magnetic holder for simple installation.
C9 (SPI Remote) Specific Features:
- Aligns color and adjusts length (number of pixels) for SPI LED strips.
- Allows changing dynamic modes, colors, brightness, and dynamic lighting features.
- Enables editing of width and color for dynamic modes.
- Works with multiple controllers.
3. Setup and Installation
3.1 Battery Installation
Both C8 and C9 remotes require two AAA batteries (not included). To install:
- Open the battery compartment cover on the back of the remote control.
- Insert two AAA batteries, ensuring correct polarity (+ and -).
- Close the battery compartment cover securely.
Note: Please ensure batteries are inserted correctly. Incorrect polarity can damage the device.
3.2 Linking/Unlinking (Pairing) with LED Lights/Controllers
The linking process typically involves the LED light or controller. Refer to your LED light/controller's manual for specific pairing instructions. Generally, the process is as follows:
- Ensure the LED light/controller is powered off.
- Power on the LED light/controller.
- Within 3 seconds of powering on, press the 'I' (Zone ON) button on the C8 remote or the 'ON' button on the C9 remote for the desired zone/controller.
- The LED light should flash to indicate successful linking.
To unlink, repeat steps 1-2, then press the 'O' (Zone OFF) button on the C8 remote or the 'OFF' button on the C9 remote for the desired zone/controller within 3 seconds. The LED light should flash to indicate successful unlinking.
4. Operating Instructions
4.1 MIBOXER C8 (8-Zone RGB+CCT Remote) Button Functions
- Color Ring: Touch to select desired RGB color.
- Indicator Light: Shows remote activity.
- CCT/Saturation Slider: Adjusts color temperature (Cool White to Warm White) or saturation.
- Brightness Dimming Slider: Adjusts light intensity.
- White Light (W): Activates pure white light mode.
- Master ON (ON): Turns all linked lights ON.
- Master OFF (OFF): Turns all linked lights OFF.
- Speed- (S-): Decreases dynamic mode speed.
- Speed+ (S+): Increases dynamic mode speed.
- Mode (M): Cycles through dynamic lighting modes.
- Zone ON (I): Turns selected zone ON (also used for linking).
- Zone OFF (O): Turns selected zone OFF (also used for unlinking).
- Zone Selection (1-8): Buttons to select individual control zones.
4.2 MIBOXER C9 (SPI Remote) Button Functions
- Color Slider: Adjusts color.
- Width Slider: Adjusts the width of dynamic effects.
- Speed Slider: Adjusts the speed of dynamic effects.
- Dimming Slider: Adjusts brightness.
- ON: Turns lights ON.
- OFF: Turns lights OFF.
- Static Mode: Activates static color mode.
- Music Mode (M): Activates music synchronization mode (if supported by controller).
- Lock: Locks the current settings.
- Dynamic Mode: Cycles through dynamic lighting modes.
- Scene Buttons (4 buttons): Save and recall custom lighting scenes.
5. Maintenance and Care
- Keep the remote control dry. Avoid exposure to moisture or liquids.
- Clean the remote with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- If the remote will not be used for an extended period, remove the batteries to prevent leakage.
- Avoid dropping the remote or subjecting it to strong impacts.
- Store in a cool, dry place away from direct sunlight and extreme temperatures.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding | Dead or incorrectly installed batteries. Out of range. Not linked. | Replace batteries, ensuring correct polarity. Move closer to the LED light/controller. Re-link the remote as per Section 3.2. |
| Limited control distance | Obstructions (walls, metal objects). Interference from other 2.4GHz devices. Low battery. | Reduce obstructions between remote and receiver. Minimize other 2.4GHz device usage. Replace batteries. |
| Lights flicker or behave erratically | Interference. Loose connection at the LED controller. | Check for sources of 2.4GHz interference. Ensure all wiring to the LED controller is secure. |
7. Specifications
7.1 MIBOXER C8 Remote Specifications
| Parameter | Value |
|---|---|
| Product Name | 8-Zone RGB+CCT Remote |
| Model No. | C8 |
| Working Voltage | 3V (AAA*2PCS) |
| Working Temperature | -10~40°C |
| EMC Standard (EMC) | ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-3 V2.3.2 (2023-01) |
| Transmitting Power | 6dBm |
| RF | 2.4GHz |
| Modulation Method | GFSK |
| Control Distance | 30m |
| Safety Standard (LVD) | EN 61347-2-11:2001+A1:2019, EN 61347-1:2015+A1:2021, EN 62493:2015+A1:2022 |
| Radio Equipment (RED) | ETSI EN 300 440 V2.2.1 (2018-07) |
| Certification | CE, EMC, RED |
7.2 MIBOXER C9 Remote Specifications
| Parameter | Value |
|---|---|
| Product Name | SPI Remote |
| Model No. | C9 |
| Working Voltage | 3V (AAA*2PCS) |
| Standby Power Consumption | 15μA |
| Working Temperature | -10~40°C |
| EMC Standard (EMC) | ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-3 V2.3.2 (2023-01) |
| Transmitting Power | 6dBm |
| RF | 2.4GHz |
| Modulation Method | GFSK |
| Control Distance | 30m |
| Safety Standard (LVD) | EN 61347-2-11:2001+A1:2019, EN 61347-1:2015+A1:2021, EN 62493:2015+A1:2022 |
| Radio Equipment (RED) | ETSI EN 300 440 V2.2.1 (2018-07) |
| Certification | CE, EMC, RED |
8. Warranty and Support
This MIBOXER remote control comes with a 2-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or improper battery installation.
For technical support or warranty claims, please contact your retailer or the official MIBOXER support channels.
9. User Tips
- Optimal Range: For best performance, try to maintain a clear line of sight between the remote and the receiver, especially when initially linking devices.
- Battery Life: Use high-quality AAA batteries for longer performance and to avoid potential leakage issues.
- Magnetic Holder: Utilize the magnetic holder (for C8) to keep your remote conveniently accessible and prevent misplacement.
- Scene Saving (C9): Experiment with the scene buttons on the C9 remote to quickly recall your favorite lighting configurations for different moods or activities.
