Important Safety Instructions
This product is a professional photographic equipment, to be operated by professional personnel only.
All transport protective materials and packaging on the product must be removed before use.
General Precautions:
- Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in serious injury, damage to the product, or other property damage.
- High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
- This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
- This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
- Extreme caution must be exercised when using it; do not touch high-temperature parts such as flash tubes and surrounding metal components to avoid burns.
- Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
- Stop using the product immediately if the flash tube or LED modeling lamp is damaged or thermally deformed, and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
- Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
- Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
- This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
- Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
- Before storing the device, make sure it is completely cooled down and the power cord (if any) is unplugged, then put it in the protective case or a ventilated dry location.
- Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
- Do not use or store this device in potentially explosive environments.
- Do not use accessories not approved by our company, as this may cause fire, electric shock or personal injury.
- Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
Lithium Battery Safety:
- Use only specified charger and follow proper usage instructions for certain products with built-in lithium batteries, within the rated voltage and temperature range.
- This product is powered by lithium batteries, which have limited lifespans, typically lasting 300-500 complete charge-discharge cycles. As usage frequency and duration increase, its maximum storage capacity will gradually decrease, which is a normal phenomenon. Please regularly check the battery's condition, and if the charging time significantly increases or the battery life significantly decreases, consider replacing it with a new battery.
- This product is equipped with lithium batteries. The following are the storage recommendations: Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Failure to perform maintenance charging over an extended period may cause the battery to suffer permanent performance degradation or even become unusable due to excessive discharge. Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.
- For products powered by lithium batteries, please note:
- Do not disassemble, crush, or puncture the battery;
- The battery is not waterproof, do not immerse it in fog or water;
- Avoid short-circuiting the battery contacts;
- Do not expose the battery to or put it into fire;
- Do not expose the battery to temperatures above 60°C;
- Keep out of reach of children;
- Protect the battery from excessive shock or vibration;
- Do not use a damaged battery;
- If the battery leaks, avoid contact with the leaking fluid;
- If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
- Confirm and comply with all relevant local laws and regulations when handling any batteries.
Introduction
Foreword
Thank you for purchasing the Godox iT32 iFlash Camera Flash & X5 Trigger!
The iT32 is a detachable camera flash with a built-in Godox 2.4G Wireless X System. It supports one-press switching between Transmitter and Receiver modes. It can be magnetically attached to the X5 Trigger (sold separately) to form a versatile TTL camera flash.
Main Features
- Detachable Design: The iT32 can be detached from the X5 (sold separately) to form a complete wireless triggering system.
- Color Touch Screen: Interactive operation with physical buttons.
- Professional Functions: Supports TTL, Manual Flash, Stroboscopic Flash, High Speed Sync, Flash Exposure Compensation (FEC), etc.
- Precise Light Control: Power range from 1/128 to 1/1 in 1/3 increments.
- Built-in Modeling Lamp: Brightness adjustable from 1 to 10 levels.
- Outstanding Performance: Max. 1.5 s recycling time at full power. Approx. 510 flashes on a full charge.
Note: The fastest recycle time is based on Godox laboratory test results. After high-intensity continuous flashes, the system will automatically extend the recycle time for safe heat dissipation, which is a normal protection mechanism. Once the device cools down, it can return to peak recycle speed.
Product overview video demonstrating detachable design, TTL & TCM, rotating head, wireless sync, color touchscreen, diffusion & catchlight panels, receiver & sender mode, magnetic accessories, diffuser attachment, and seamless switching between X5 triggers.
What's in the Box
The package includes the following items:

Contents of the Godox iT32 iFlash Camera Flash package.
- Flash Body ×1
- USB-C Cable ×1
- Magnetic Mini Stand ×1
- Diffuser ×1
- Magnetic Color Filter (1/2 orange) ×1
- Magnetic Color Filter (1/1 orange) ×1
- Storage Bag ×1
- Instruction Manual ×1
Separately Sold Accessories
Use with Godox accessory system for the best shooting results and experience:
- TTL wireless flash trigger X5 series
- Flash trigger X2T series
- Flash trigger XProII series
- Flash trigger X3 series
- Magnetic Accessory Kit MA02
Names of Parts
Flash Body

Visual representation of the iT32 flash body features.
- Flash Head
- Wide-angle Diffuser (Transparent, inside the flash head)
- Catchlight Panel (White, inside the flash head)
- LED Modeling Lamp
- Photocell Sensor
- Sync Cord Jack
- USB-C Port (Charging/firmware upgrade)
- Touch Display
- < MENU > MENU Button
- < SET > Setting Button
- < Test/Power Button
- Select Dial
- Select Dial Alignment Marker
TTL Wireless Flash Trigger X5 (Sold Separately)
- Indicator
- < -/❑ > Decrease / Battery / Power Button
- < +/M > Increase / Mode Button
- Hot Shoe Locking Ring
- Hot Shoe
- Magnetic Point ×4
Note: The appearances and contacts of hot shoes vary in different models.
Setup: Quick Start
1. Install the X5 Trigger
Align the X5 with the bottom of the iT32 in the correct orientation as shown, and attach it magnetically. Ensure it fits securely. Once installed, the "C" icon in the menu interface will light up (Different modes have different icons).
2. Install the Diffuser
Align the diffuser with the flash head in the correct orientation as shown. Insert it until it clicks into place.
3. Attach to Camera
Turn the Hot Shoe Locking Ring to the right to the top (loosen). Slide the hot shoe into the camera hot shoe, then turn the ring to the left to lock. (Ensure both devices are powered off before installation).
4. Power On the Flash
Long Press the < Test/Power > Button. When the unlock icon appears, swipe the screen or turn the Select Dial to unlock as prompted. The device will automatically power off if not unlocked within 6 seconds.
5. Power Off the Flash
Long Press the < Test/Power > Button until the display turns off.
6. Power On/Off the X5 Trigger
Long press the < -/❑ > button. The device will power off automatically after the indicator displays the battery level. To wake up the device, press any button or mount it on a flash. The device cannot be awakened by the camera.
Check the Trigger Status via the Indicator:
| Indicator | Description |
|---|---|
| Flash green | Unconnected to camera in TTL. |
| Constant on green | Connected to camera in TTL. |
| Flash orange | Unconnected to camera in M. |
| Constant on orange | Connected to camera in M. |
| Flash red slowly | Low battery level. |
| Light off | Sleep mode or power off, press any button to wake. |
Battery Level Indication & Charging
iT32 Battery Level Indication
The battery icon is displayed in the top right corner of the screen.
| Battery Level Indication | Meaning |
|---|---|
| 3 grids | Full |
| 2 grids | Middle |
| 1 grid | Low |
| Blank grid | Lower battery, please recharge it. |
| Blinking | The battery level is going to be used out, and the flash is not functional in this status. |
Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long period.
X5 Trigger Battery Level Indication
- Check via the flash: Mount the X5 on the iT32 → Swipe down on the screen to enter the menu → Tap the "C" icon to view the trigger model and battery level.
- Check via the Indicator: Press and hold the < -/❑ > button of flash trigger until the indicator turns red. Then check the battery level by observing the number of red flashes from the indicator. (One flash indicates low battery, four flashes indicate full charge, and so on.)
Charging Instructions
- iT32: Charge the device using the included USB-C cable connected to a power adapter (sold separately). Charging time is approx. 1 hour and 10 minutes.
- X5: Mount the device on the iT32 to charge. It triggers once every 10 seconds at full battery level, for about 4000 times. The charging output port of iT32 is not universal and only supports charging X5.
Operating Modes
Wi-Off Mode (With Flash Trigger X5) - On-Camera Mode
This mode is used when the iT32 is mounted directly on the camera hotshoe with the X5 trigger attached.
- Touch Screen: Slide the screen to enter menu interface, click the "On-Camera Mode" icon to choose.
- Buttons and Select Dial: Press the MENU button to enter menu interface, rotate the select dial to choose the "On-Camera Mode" icon, then press the SET button to choose and enter wi-off mode.
TTL Auto Flash
The camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed.
- Touch Screen: Slide the screen to enter menu interface, click the “TTL / M / Multi" icon to choose "TTL" and enter TTL auto flash mode.
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the “TTL/M/Multi“ icon, then press the SET button to choose "TTL".
- FEC Amount Setting: Tap the "-/+" icon or rotate the select dial to set the exposure compensation (Range: -3.0 to +3.0, Increment: 1/3 stop). Drag the yellow progress bar for quick adjustment.
M Manual Flash
S1 and S2 photocell functions are available in M mode, and the flash output is adjustable. To obtain a correct flash exposure, use a handheld flash meter to determine the required flash output. This mode supports S1/S2 optical control triggering.
- Touch Screen: Slide the screen to enter menu interface, click the “TTL/M/Multi" icon to choose "M" and enter M manual flash mode.
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the TTL/M/Multi icon, then press the SET button to choose "M".
- Output Power Setting: Press the "-/+" icon or rotate the select dial to adjust the power from 1/128 to 1/1 with ±1/3 increment each step. Drag the yellow progress bar for quick adjustment.
S1/S2 Photocell
The photocell sensor will enter standby mode to continuously monitor changes in ambient light levels after the photocell triggering is turned on.
- S1 Photocell Unit: With this function, the flash will fire synchronously when the main flash fires.
- S2 Photocell Unit (pre-flash): This is useful when cameras have pre-flash function. With this function, the flash will ignore a single "pre-flash” from the main flash and will only fire in response to the second, actual flash from the main unit.
Note: Enter setting interface to switch between S1/S2 photocell or turn off this function.
Multi Stroboscopic Flash
Fires a rapid series of flashes during a single exposure to capture the continuous trajectory of moving objects. You can set the flash times, frequency (number of flashes per second), and power.
- Number of flashes: 1-100
- Flash frequency: 1-100Hz
- Flash output range: 1/128-1/4
- Touch Screen: Slide the screen to enter menu interface, click the <TTL/M/Multi> icon to choose <Multi>.
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the “TTL/M/Multi" icon, then press the SET button to choose Multi. Press "MENU" Button to return to the menu interface. Directly rotate the select dial can adjust the output power. Press the SET button to choose the “times/frequency" icon on the upper right corner, then rotate the select dial can adjust the respective parameters.
Calculating the Shutter Speed in Multi Flash Mode
During multi flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
Number of Flashes ÷ Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the flash frequency is 5Hz, the shutter speed should be at least 2 seconds.
Note:
- Multi flash is more effective when shooting highly reflective objects against a dark background.
- Using a tripod and TTL flash trigger is recommended.
- This mode supports BULB shooting.
- 1/1 or 1/2 power output, as well as High-speed/Rear-curtain/Front-curtain sync, are not supported in this mode.
Maximum Time of Consecutive Flashes
| Flash Output | Flash Frequency (Hz) | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6-7 | 8-9 | |||
| 1/4 | 8 | 6 | 4 | 3 | 3 | 2 | 2 | ||
| 1/8 | 14 | 14 | 12 | 10 | 8 | 6 | 5 | ||
| 1/16 | 30 | 30 | 30 | 20 | 20 | 20 | 10 | ||
| 1/32 | 60 | 60 | 60 | 50 | 50 | 40 | 30 | ||
| 1/64 | 90 | 90 | 90 | 80 | 80 | 70 | 60 | ||
| 1/128 | 100 | 100 | 100 | 100 | 100 | 90 | 80 | ||
| Flash Output | Flash Frequency (Hz) | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 10 | 11 | 12-14 | 15-19 | 20-50 | 60-100 | ||||
| 1/4 | 2 | 2 | 2 | 2 | 2 | 2 | |||
| 1/8 | 4 | 4 | 4 | 4 | 4 | 4 | |||
| 1/16 | 8 | 8 | 8 | 8 | 8 | 8 | |||
| 1/32 | 20 | 20 | 20 | 18 | 16 | 12 | |||
| 1/64 | 50 | 40 | 40 | 35 | 30 | 20 | |||
| 1/128 | 70 | 70 | 60 | 50 | 40 | 40 | |||
Note: To avoid overheating and deteriorating the flash head, do not use multi flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 minutes. Otherwise, the flash may stop automatically.
Sender Mode (With Flash Trigger X5)
This chapter explains how to perform wireless multi-flash shooting using the iT32 + X5 as the transmitter unit, combined with flashes that feature 2.4G wireless receiver functions (sold separately).
Outdoor Flash such as AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT32, iT30Pro, V100, V480 and Lux Master.
In this chapter, the iT32 + X5 mounted on the camera is referred to as the "Transmitter," and the controlled flashes are referred to as "Receivers."
Note:
- The channel, group, and ID of the sender and receiver units should be set to the same.
- The above listed are only some models that can be controlled by iT32+X5.
- Group D is only available when the iT32 + X5 C/Cm is set as the transmitter.
Wireless Multiple Flash Shooting in TTL Auto Flash Mode
Set the transmitter groups (A, B, C) to TTL mode and adjust the exposure compensation. Receivers will fire automatically based on their assigned group settings.
Wireless Multiple Flash Shooting in M Manual Flash Mode
Set the transmitter groups (A, B, C) to M mode and adjust the Flash power. Receivers will fire automatically based on their assigned group settings.
Wireless Multiple Flash Shooting in Different Flash Modes
Set the transmitter groups (A, B, C) to different flash modes and adjust the exposure compensation or Flash power. Receivers will fire automatically based on their assigned group settings.
Wireless Multiple Flash Shooting in Multi Flash Mode
Set the transmitter to Multi mode and uniformly set the desired power output, flash times, and frequency. The receivers will automatically sync with the transmitter's settings for shooting.
Receiver Mode (With Flash Trigger X5)
The iT32+X5 combination acts as a receiver unit to receive wireless triggering signals.
- Touch Screen: Slide the screen to enter menu interface, click the "Receiver Mode" icon to choose.
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the "Receiver Mode" icon, then press the < SET > button to choose.
TTL Auto Flash
- Touch Screen: Slide the screen to enter menu interface, click the “TTL/M/Multi" icon to choose "TTL".
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the “TTL/M/Multi" icon, then press the SET button to choose "TTL" and enter TTL auto flash mode.
- Group Selection: Press the group icon, or press the SET button and rotate the select dial to choose a certain group.
M Manual Flash
- Touch Screen: Slide the screen to enter menu interface, click the “TTL/M/Multi" icon to choose "M" and enter “M” manual flash mode.
- Select Dial and Buttons: Press the MENU button to enter menu interface, rotate the select dial to choose the “TTL/M/Multi icon”, then press the < SET > button to choose M.
- Group Selection: Press the group icon, or press the < SET > button and rotate the select dial to choose a certain group.
- Output Power Setting: Press the "-/+" icon or rotate the select dial to adjust the Flash power. Drag the yellow progress bar for quick adjustment.
Multi Stroboscopic Flash
- Touch Screen: Slide the screen to enter menu interface, click the “TTL/M/Multi" icon to choose "Multi", then slide the screen up to enter the main interface. Press the group icon on the upper left corner to choose a certain group. Press the "-/+" icon or directly pull the progress bar can adjust the flash power.
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the TTL/M/Multi icon, then press the SET button to choose Multi. Press the < MENU > button to enter the main interface, Press the < SET > button and rotate the select dial to choose among number of flashes, flash frequency, group and output power, then press the < SET > button and rotate the select dial can adjust the respective parameters.
Receiver Mode (Separated Triggering)
Remove the X5 Transmitter from the iT32 and insert it into the camera's hot shoe to wirelessly trigger the flash via the camera shutter. Once the X5 is removed, the iT32 automatically switches to RX (Receiver) mode.
- Flash Mode Switch: Press and hold the < +/M > button of X5 to switch between TTL mode and M mode. The indicator of flash trigger will flash green in TTL auto flash mode, flash orange in M manual flash mode.
- Output Power Setting: In M Mode, press the < -/❑ > or < +/M > button of X5 to set the power.
- FEC Amount Setting: In TTL mode, press the < -/❑ > or < +/M > button of FEC amount X5 to set.
Sync Triggering Other Godox Flashes
Take AD100ProII as an example:
- Remove X5 from iT32, and insert it into the camera hot shoe.
- Set AD100ProII: Press the < MENU > button to enter menu interface, rotate and press the < SET > dial to select and enter wireless settings, set the group, channel, ID to the same as iT32.
- Press the camera shutter to sync trigger iT32 and AD100ProII.
Flash Functions
High-speed Sync (HSS)
High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.
- Touch Screen: Slide the screen to enter menu interface, click the "HSS" icon to choose "HSS".
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the "HSS" icon, then press the < SET > button to switch to "HSS".
Note:
- The minimal flash power is 1/16 in HSS mode.
- Choose HSS mode in camera settings for iT32+X5 F.
- When using Nikon camera with iT32+X5 N, the HSS is on by default in high-speed camera shutter, while HSS is off in low-speed shutter.
Second-curtain Sync
With a slow shutter speed and second-curtain sync, you can create a light train following the subject. The flash fires right before the shutter closes.
- Touch Screen: Slide the screen to enter menu interface, click the "Second-curtain Sync" icon to choose.
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the "Second-curtain Sync" icon, then press the < SET > button to switch.
Note:
- Choose < REAR > flash mode in the settings of Sony camera for iT32+X5 S.
- Choose < MENU > button Flash Light Function Setting, and select REAR < REAR > flash mode on Fujifilm cameras for iT32+X5 F.
- For iT32+X5 N, press < Flash > button on Nikon camera, rotate the dial until the < REAR > appears on the control panel to enter rear-curtain sync mode, set the camera shutter.
- For iT32+X5 O, press <OK> button on OM SYSTEM camera or < MENU > button on Panasonic camera to enter the setting. When the < 2nd-C > appears on the display, set the camera shutter.
First-curtain Sync
With a first-curtain sync, you can create a light train leading the subject. The flash fires when the shutter starts.
- Touch Screen: Slide the screen to enter menu interface, click the "First-curtain Sync" icon to choose.
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the "First-curtain Sync" icon, then press the < SET > button to switch.
Note: Please refer to the second-curtain sync section above for the settings of different cameras.
Modeling Lamp
- Touch Screen: Slide the screen to enter menu interface, click the "Modeling Lamp" icon to enter modeling lamp settings. Tap the "Modeling Lamp Switch" icon to turn the modeling lamp on/off. Once turned on, drag the progress bar to set the brightness (Range: 1–10, Step: 1).
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the "Modeling Lamp" icon, then press the < SET > button to enter modeling lamp settings, press the < SET > button and rotate the select dial to adjust brightness.
- Inter Function: The modeling lamp turns off automatically when the flash fires. In the modeling lamp interface, press the inter switch, or rotate the select dial to choose inter switch and press the < SET > button, to turn on or off the inter function.
Note: Turn on the inter function, the modeling lamp will automatically turn off when flashing.
Screen Lock
- Touch Screen: Slide the screen to enter menu interface, click the "Screen Lock" icon to turn on the screen lock function. Press and hold the < SET > button for 2s to unlock.
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the “Screen Lock” icon, then press the < SET > button to turn on the screen lock function. Press and hold the < SET > button for 2s to unlock.
Wireless Settings
- Touch Screen: Slide the screen to enter menu interface, click the "Wireless Settings" icon to enter wireless settings.
- Select Dial and Buttons: Press the < MENU > button to enter menu interface, rotate the select dial to choose the "Wireless Settings" icon, then press the < SET > button to enter wireless settings.
Channel Settings
If there are other wireless flash systems nearby, you can change the wireless channels to prevent signal interference. Channel Range: 01 - 32.
- Touch Screen: Slide the "Channel" box to settings your desired channel.
- Select Dial and Buttons: Rotate the select dial to choose “Channel” box, then press the < SET > button to enter channel settings, rotate the select dial and press the SET button to choose your desired channel.
ID Settings
In addition to changing the Channel, you can also change the Wireless ID to avoid signal interference. Wireless ID Range: OFF / 01 - 99.
- Touch Screen: Slide the “ID” box to turn off the ID, or settings your desired ID.
- Select Dial and Buttons: Rotate the select dial to choose "ID" box, then press the < SET > button to enter ID settings, rotate the select dial and press the SET button to choose your desired ID.
Wireless Sync
Automatically sets the receiver units to the same channel and ID as the transmitter. Available in Transmitter and Receiver modes only.
Receiver Wireless Sync
Preconditions:
- Set iT32+X5 to sender mode.
- Assume retro camera flash Lux Master as the receiver.
- Touch Screen: Click the iT32 and Lux Master.
- Buttons and Select Dial: Rotate the select dial on iT32 to choose "SYNC” icon, then press the < SET > button. Rotate the select dial on Lux Master to choose “SYNC” icon, then press the < SET > button.
Sender Wireless Sync
Preconditions:
- Set iT32+X5 to receiver mode.
- Assume flash trigger X3 as the sender.
- Touch Screen: Click the iT32 and X3.
- Select Dial and Buttons: Rotate the select dial on iT32 to choose “SYNC” icon, then press the < SET > button. Rotate the select dial on X3 to choose “SYNC” icon, then press the select dial.
iT32+X5 Wireless Sync
When the transmitter and receiver are both iT32+X5, wireless sync is also available.
Troubleshooting
The flash does not fire
- Ensure the flash is securely mounted on the camera hot shoe and the electrical contacts are properly connected.
- If the contacts are dirty, clean them with a dry, lint-free cloth.
- If the < Flash > or < HSS > does not appear in the camera viewfinder, wait for the flash to recycle.
- Check the battery level. If the battery is low, replace or charge it immediately.
Underexposure or Overexposure
- In High Speed Sync mode, the effective flash range is reduced. Ensure the subject is within the effective flash range displayed on the screen.
- If the main subject is too dark or too bright, set the appropriate Flash Exposure Compensation (FEC).
The buttons or touchscreen do not respond
- Software glitch: Press the < Test/Power > and < MENU > buttons simultaneously to force shutdown, then restart the device to check for normal operation.
The Reason & Solution of Not Triggering in Godox 2.4G Wireless
- Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
→To adjust the channel CH setting (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working. - The flash has not completed recycling, or the recycling speed cannot keep up with the continuous shooting speed.
→ Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode (a pre-flash is needed in TTL mode). - The transmitter and receiver are too close to each other.
→ Please turn on the "close distance wireless mode". Set the triggering distance to 0-30m. - Low Battery
→ Please replace the battery or charge it in time. - The flash's firmware is an older version
→ Please upgrade the firmware of the flash. - The camera's firmware is an older version
→ Please upgrade the firmware of the camera referring to its instruction manual.
Firmware Upgrade
Visit the official Godox website at https://www.godox.com.cn/firmware-G3/ to download the Godox G3 software and the latest firmware file.
- Connect: With the device powered off, press and hold the < SET > Button and connect it to a computer using the included USB-C cable.
- Upgrade: Open the Godox G3 software, select the firmware file, and execute the upgrade.
Specifications
| Model | iT32+X5 S | iT32+X5 C/Cm/N/F/O/L |
|---|---|---|
| Global Shutter Sync Shooting | Provided | Unprovided |
| Radio Wireless Global Shutter Sync | Provided | Unprovided |
| Guide Number (1/1 step) | Approx. GN18 (ISO 100, in meters) | |
| Number of Flashes (1/1 step) | Approx. 510 | |
| Recycle Time (1/1 step) | Approx. 1.5s | |
| Flash Duration (t0.1) | 1/1000s - 1/30000s | |
| Flash Exposure Compensation (FEC) | Range:-3.0~ + 3.0; Step:1/3 | |
| Multi Flash | Supported (Max. 100 times, 100 Hz) | |
| Exposure Control System | TTL auto flash and manual flash | |
| Sync Mode | High-speed sync (up to 1/8000 seconds, first-curtain sync, and second-curtain sync) | |
| Wireless Function | Sender / Receiver | |
| Sender Groups | M, A, B, C (iT32+X5 S / N / F / O / L) A, B, C, D (iT32+X5 C / Cm) | |
| Receiver Groups | A, B, C, D | |
| Transmission Range | Max. 80m (Max. 20m in separated triggering) | |
| Channels | 32:01~32 | |
| IDs | OFF/1-99 | |
| Sync Triggering Mode | Hot shoe, 2.5 mm sync cord | |
| Power Saving | Provide standby and auto off functions | |
| Lithium Battery | iT32: 7.4V/900mAh X5: 3.8V/100mAh | |
| Work Temperature | -10°C - 45°C | |
| Dimension | iT32: 2.2" × 1.54" × 3.98"; X5: 1.26″ × 1.26″ × 1.06" (Minor differences may exist depending on the model.) | |
| Net Weight | iT32: 169 g; X5: 23 g (Minor differences may exist depending on the model.) | |
Note: Specifications and data may subject to changes without notice.
Compatible Camera Models
Note: These tables only list the tested camera models. For the compatibility of other models, a self-test is recommended. Rights to modify these tables are retained.
iT32+X5 C (for Canon)
Can be used on the following Canon camera models: 80D, 90D, 7D, 6D, 70D, 750D, 760D, 5DMarkIV, EOS 1DX, 6DMarkII, 77D, 800D, 5DMarkIII, 5DMarkII, 60D, 7D MarkII, 600D, 50D, 30D, 40D, 500D, M5, M3, M50, R, RP, M6II, R5, 1500D, 3000D, R7, R6II, R50, R8, R5C, R10, R100, R5II, R3, 200DII.
Note: Requires an adapter for cameras with a multi-function shoe.
iT32+X5 Cm (for Canon Multi-function Shoe)
Compatible with the following Canon camera models: EOS R1, EOS R3, EOS R5 Mark II, EOS R6 Mark II, EOS R7, EOS R8, EOS R10, EOS R50, EOS R50V, PowerShot V1.
iT32+X5 N (for Nikon)
Can be used on the following Nikon camera models: D800, D750, D700, D610, D500, D200, D300S, D5, D4, D810, D780, D5300, D5200, D5100, D5000, D3300, D3100, D60, Z6, Z7II, Z8, ZFC.
iT32+X5 S (for Sony)
Can be used on the following Sony camera models: α77II, α99, α77, DSC-RX10, α6000, α7R, α350, α7RII(4.0), α7RIII, α7M3, α9, α7RIV, α7R5, α7MIV, ZV-E10, A9III, A7C, A7CII, α6400, α6500.
iT32+X5 F (for Fujifilm)
Can be used on the following Fujifilm camera models (categorized by control type):
- A: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S20, X-T5
- B: X-Pro1, X-T10, X-E1, X-A3
- C: X100F, X100T
iT32+X5 O (for Olympus / Panasonic)
Can be used on the following OM SYSTEM or Panasonic camera models: OM SYSTEM: E-M1, PEN-F, E-M10II, E-PL8, E-P5, E-M10III. Panasonic: GH4, LX100, DMC-GF1, DMC-G85, DMC-GX85, DMC-LX100, DMC-FZ2500GK, S1.
iT32+X5 L (for Leica)
Compatible with the following Leica camera models: SL2, M10, Q2, TYP 601, 7323, SL3.
Compatible Camera Models & Functions Support
| Camera | TTL Flash | M Manual Flash | Multi Flash | ||||
|---|---|---|---|---|---|---|---|
| Front | Rear | HSS | Front | Rear | HSS | ||
| A | √ | √ | √ | √ | √ | √ | √ |
| B | √ | √ | -- | √ | √ | -- | √ |
| C | √ | √ | -- | √ | √ | -- | √ |
| Camera | 2.4G Wireless Control | ||||||
|---|---|---|---|---|---|---|---|
| TTL Flash | M Manual Flash | Multi Flash | |||||
| Front | Rear | HSS | Front | Rear | HSS | ||
| A | √ | √ | √ | √ | √ | √ | √ |
| B | √ | √ | -- | √ | √ | -- | √ |
| C | √ | √ | -- | √ | √ | -- | √ |
Note: X100T do not have second curtain sync (REAR) function.
Maintenance
General Care
- Avoid Drops: The device may malfunction if subjected to strong shocks or vibration.
- Keep Dry: This product is NOT waterproof. Strictly do not operate with wet hands or use in rainy, damp, or high-humidity environments (e.g., bathrooms).
- Avoid Sudden Temperature Changes: Condensation may occur if the product is moved from a cold environment to a warm one. To prevent this, place the product in a carrying bag or plastic bag beforehand to allow it to adjust to the temperature change.
- Avoid Strong Magnetic Fields: Strong static electricity or magnetic fields produced by devices such as radio transmitters may interfere with the normal operation of this product.
X5 Contact Cleaning
After prolonged use, metal contacts may accumulate dust or oxidize, causing poor contact manifested as charging interruption or data loss. Use a dry, lint-free soft cloth to wipe the contact surface in one direction to remove oxides.
Warning: Do not use metal tools, sandpaper, or wet wipes to avoid scratching the contacts or causing a short circuit.
Over-Temperature Protection
- To avoid overheating and deteriorating the flash head, do not fire more than the mentioned below continuous flashes in fast succession at 1/1 full power, or fire more than 40 continuous flashes in fast succession at 1/1 full power in HSS mode.
- If you fire more than the mentioned below continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycle time over 10 seconds. If this occurs, allow a rest time of about 10 minutes.
- When the over-temperature protection is started, a thermometer icon is shown on the display.
Number of flashes that will activate over-temperature protection:
| Power Level | Number of continuous flashes |
|---|---|
| 1/1 | 40 |
| 1/2 | 60 |
| 1/4 | 120 |
| 1/8 | 200 |
| 1/16 | 300 |
| 1/32 | 600 |
| 1/64 | 1200 |
| 1/128 | 2000 |
Number of flashes that will activate over-temperature protection in HSS mode:
| Power Level | Number of continuous flashes |
|---|---|
| 1/1 | 40 |
| 1/2 | 75 |
| 1/4 | 100 |
| 1/8 | |
| 1/16 |
User Tips
- Seamless Operation: Users appreciate the magnetic trigger design, allowing for quick detachment and immediate use as a flash.
- Power & Portability: Despite its small size, the speedlight is noted for being powerful. It fits well on compact cameras like the Sony a6700.
- Trigger Charging: Be aware that the X5 trigger recharges when attached to the iT32 flash unit.
- Compatibility Check: For Canon users, the iT32+X5 C is compatible with models like the T5, T6i, and RP. For other Canon models like the T7, ensure you select the correct X5 variant (C or Cm) and check the compatibility list.
Warranty & Support
Warranty Period
The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time. The purchase date is considered as the date registered on the warranty card when buying the product.
Maintenance and Service Support Information
| Parts | Maintenance Period (month) | Warranty Service Type |
|---|---|---|
| Internal circuit board | 12 | Customer sends the product to designated site |
| Other items (flash tube, optical accessories, cables, package, etc) | NO | Without warranty |
Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases:
- The product or accessory has expired its warranty period;
- Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
- Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
- The original identifying information of product or accessory is modified, alternated, or removed;
- No valid warranty card;
- Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
- Breakage or damage caused by force majeure or accident;
- Breakage or damage that could not be attributed to the product itself.
Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.
How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Godox After-sale Service Call: +86-755-29609320 (8062)
