1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your HORACO 10G SFP+ to RJ45 Media Converter. This device is designed to facilitate high-speed data transmission between SFP+ fiber optic networks and RJ45 Ethernet networks, supporting adaptive rates from 10M to 10G. Please read this manual thoroughly before using the product to ensure proper functionality and safety.

Figure 1: HORACO 10G SFP+ to RJ45 Media Converter
2. Product Overview
The HORACO 10G Media Converter offers high-speed, reliable data transmission with flexible rate adjustment and robust features for various networking environments.
2.1 Key Features
- 10G High-Speed Transmission: Supports 100M/1G/2.5G/5G/10G auto-negotiation rate transmission for faster and more stable connections.
- Three DIP Switch Rates: Flexible adjustment of operating rates (10G, 2.5G, Gigabit) via DIP switches to meet different network scenarios.
- Port Lightning Protection: Enhanced device security protection against lightning-induced failures.
- Powerful Heat Dissipation: Multiple heat dissipation openings on both sides with a built-in heat sink ensure normal high-speed operation and withstands harsh environments from -30°C to 75°C.
- DC 5-15V Power Supply: Supports multiple power supply options (DC 5V2A, DC 12V1/2A, DC 15V1A).
- Plug and Play: No complex setup required; simply insert the module, connect Ethernet cables, and power supply. Supports hot-plugging.

Figure 2: 10Gbps High-Speed Transmission Capability

Figure 3: Overview of Six Core Features
2.2 Port Display and Indicators
Familiarize yourself with the ports and indicator lights on the media converter:

Figure 4: Port Display and Indicator Lights
- 10G/2.5G/1G Optical Port (SFP+): Connects to SFP+ optical modules for fiber optic connections.
- 10G/2.5G/1G/100M Ethernet Port (RJ45): Connects to standard Ethernet cables.
- DC Power Port: Connects to the power adapter (5V2A~15V1A recommended).
- Rate DIP Switch (B1, B2): Used to manually set the operating speed of the SFP+ interface and RJ45 port.
- Grounding Screw Hole: For grounding the device to prevent electrical damage.
- Indicator Lights:
- Link/Act (SFP+): Indicates link status and activity for the optical port.
- Misc/Speed/Duplex (RJ45): Indicates miscellaneous status, speed, and duplex mode for the RJ45 port.
- Power: Indicates the device is powered on.
3. Setup
The HORACO Media Converter is designed for easy plug-and-play installation. Follow these steps to set up your device:
3.1 Connection Diagram
A typical connection involves two transceivers to extend an Ethernet connection over fiber, or to convert between fiber and copper for a single device.

Figure 5: Example Connection Diagram
3.2 Installation Steps
- Power Off: Ensure all devices (router, camera, etc.) are powered off before making connections.
- Insert SFP+ Module: Insert a compatible SFP+ optical module into the 10G/2.5G/1G Optical Port (1) of the media converter.
- Connect Fiber Cable: Connect the fiber optic cable to the SFP+ module.
- Connect Ethernet Cable: Connect an Ethernet cable from your network device (e.g., router, camera, PC) to the 10G/2.5G/1G/100M Ethernet Port (2).
- Connect Power: Connect the DC power adapter to the DC Power Port (3) and then plug it into a power outlet.
- Power On: Power on all connected devices. The indicator lights (6) should illuminate, indicating a successful connection.
- Grounding (Optional but Recommended): For enhanced safety and protection against electrical surges, connect a grounding wire to the Grounding Screw Hole (5) and to a suitable ground point.
4. Operating Instructions
The media converter supports various speeds, which can be configured using the DIP switches.
4.1 DIP Switch Rate Adjustment
The Rate DIP Switch (4) allows you to manually set the operating speed. Ensure the device is powered off before adjusting DIP switches.
4.1.1 10G Rate Link

Figure 6: 10G Rate Link DIP Switch Setting
- DIP Switch B1B2: Both switches in the upward position.
- SFP+ Interface: 10G-R mode.
- Ethernet Port: 10M/100M/1G/2.5G/5G/10Gbps.
- Indicator Lights: All three misc/speed/duplex indicator lights remain steadily lit.
4.1.2 2.5G Rate Link

Figure 7: 2.5G Rate Link DIP Switch Setting
- DIP Switch: B1 upward, B2 downward.
- SFP+ Interface: 2500BASE-X mode.
- Ethernet Port: 10M/100M/1G/2.5G rates.
- Indicator Lights: Both misc/duplex indicator lights remain steadily lit.
4.1.3 Gigabit Rate Link

Figure 8: Gigabit Rate Link DIP Switch Setting
- DIP Switch: B1 downward, B2 upward.
- SFP+ Interface: 1000BASE-X mode.
- Ethernet Port: 10M/100M/1G rates.
- Indicator Lights: Both speed/duplex indicator lights remain steadily lit.
5. Maintenance
To ensure the longevity and optimal performance of your media converter, follow these maintenance guidelines:
- Keep Clean: Regularly clean the device and its ports with a soft, dry cloth. Avoid using liquid cleaners.
- Proper Ventilation: Ensure the device is placed in a well-ventilated area to allow for proper heat dissipation. Do not block the ventilation openings.
- Environmental Conditions: Operate the device within the specified temperature range (-30°C to 75°C) and humidity levels. Avoid extreme conditions.
- Cable Management: Keep cables organized and free from kinks or excessive bends to prevent damage and ensure stable connections.
- Power Supply: Use only the recommended power supply (DC 5V2A~15V1A) to prevent damage to the device.

Figure 9: High Speed Heat Dissipation Design

Figure 10: Temperature Resistance
6. Troubleshooting
If you encounter issues with your media converter, refer to the following common troubleshooting steps:
- No Power:
- Check if the power adapter is securely connected to both the device and the power outlet.
- Verify that the power outlet is functional.
- Ensure the power adapter meets the specified voltage and current requirements (DC 5V2A~15V1A).
- No Link Light:
- For SFP+ Port: Ensure the SFP+ module is correctly inserted and compatible. Check the fiber optic cable for damage and proper connection.
- For RJ45 Port: Check the Ethernet cable for damage and ensure it's securely connected to both the converter and the network device. Try a different Ethernet cable.
- Verify that the connected network devices are powered on and functioning correctly.
- Incorrect Speed/Duplex:
- Check the DIP switch settings (B1, B2) to ensure they are configured for the desired speed (10G, 2.5G, Gigabit) as described in Section 4.1.
- Ensure the connected network devices support the selected speed and duplex mode.
- Intermittent Connection:
- Check all cable connections for looseness or damage.
- Ensure the device is not overheating. Provide adequate ventilation.
- Test with different cables and SFP+ modules if possible.
- Device Not Recognized:
- Restart the media converter and all connected network devices.
- Ensure the network interface card (NIC) on your connected device is properly installed and its drivers are up to date.
If the problem persists after trying these steps, please contact technical support.
7. Specifications
Below are the technical specifications for the HORACO 10G SFP+ to RJ45 Media Converter (Model LG-T8801S):

Figure 11: Product Parameters
| Feature | Description |
|---|---|
| Product Name | 10G SFP 1 Optical 1 Electrical Media Converter |
| Model Number | LG-T8801S |
| Brand Name | HORACO |
| Origin | Mainland China |
| Certification | CE, FCC, RoHS |
| Ethernet Port | 1* 10G SFP+ Port, 1*10G RJ45 Port |
| RJ45 Port Rates | 100M/1000M/2.5G/5G/10G Adaptive |
| SFP+ Port Rates | 1G/2.5G/10G |
| Backplane Bandwidth | 13.125Gbps |
| Packet Forwarding Rate | 5.784Mpps (29.76Mpps from JSON) |
| MAC Address Table Size | 8K |
| Network Protocol | IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.3ad, IEEE 802.3at |
| Voltage Supply | 5-15V Power Supply, DC 12V/1A~2A Recommended |
| Operating Temperature | -30°C to +75°C |
| Product Dimensions (L x W x H) | 94mm x 70mm x 26mm |
| Net Weight | 197g |
| Package Dimensions | 120mm x 165mm x 85mm |
| Gross Weight | 349g |
| Wireless Function | No |
| High-concerned chemical | None |
| Transmission Distance | 100BASE-TX: Cat5 or later UTP (150m), 2500/1000BASE-TX: Cat6 or later UTP (100m), 5G BASE-TX: Cat6 or later UTP (80m), 10G BASE-TX: Cat6 or later UTP (50m), SFP: 100M/1G/2.5G/10G single-mode/multimode optical module, maximum distance ≤ 120km (depending on the optical module) |
8. Warranty and Support
HORACO provides the following warranty and support for this product:
- Warranty: 1 Year Warranty from the date of purchase.
- Technical Support: Lifetime Professional Technical Support is available for all HORACO products.
For technical assistance or warranty claims, please contact HORACO Official Store customer service.
9. User Tips
Based on general usage and product features, here are some tips for optimizing your experience:
- DIP Switch Configuration: Always power off the device before adjusting the DIP switches to prevent potential damage or incorrect configuration.
- Cable Quality: For optimal 10G performance, use high-quality Cat6a or Cat7 Ethernet cables for RJ45 connections and appropriate fiber optic cables for SFP+ modules.
- SFP+ Module Compatibility: Ensure that the SFP+ optical modules used are compatible with the media converter and meet the requirements of your fiber network.
- Environmental Stability: While the device is designed for wide temperature ranges, maintaining a stable operating environment can further enhance its lifespan and reliability.
- Grounding: Utilize the grounding screw hole for added protection, especially in environments prone to electrical surges.