1. Introduction
This manual provides detailed instructions for the Estardyn 1.3 Inch OLED Display with integrated 4x4 or 4x16 Keyboard Module. Designed for DIY projects, this module is compatible with popular development platforms like Arduino and Raspberry Pi. It features a 128x64 pixel OLED display and an IIC (I2C) interface for communication.

2. Specifications
| Feature | Description |
|---|---|
| Display Type | OLED |
| Display Size | 1.3 inches |
| Resolution | 128x64 pixels |
| Driver IC | SSD1116 (also compatible with SH1116/SH1315) |
| Interface | IIC (I2C) |
| Operating Voltage (VCC) | 2.2V - 5.5V |
| Logic High Level (SCL/SDA) | 2.2V - 5.5V |
| Keypad Options | 4-key or 16-key matrix |
| Module Dimensions (approx.) | Length: 15 cm, Width: 10 cm, Height: 1 cm |
| Module Weight (approx.) | 0.021 kg |
| Customization | Yes |
3. Setup and Connection
This section details the physical connections required to integrate the OLED display and keypad module into your project. The module communicates via the IIC (I2C) protocol.
3.1 Pinout Description
The module typically features the following pins:
- GND: Power Ground
- VCC: Power Supply (2.2V - 5.5V)
- SCL: IIC Clock Line (High level: 2.2V - 5.5V)
- SDA: IIC Data Line (High level: 2.2V - 5.5V)
For the keypad, the pins are typically labeled R1-R4 (Rows) and C1-C4 (Columns) for a 4x4 matrix, or more for a 4x16 matrix.

3.2 Wiring Diagrams
Below are example wiring diagrams for common development boards. Ensure your power supply matches the module's VCC requirements (2.2V-5.5V).
3.2.1 General Wiring and Keypad Matrix

3.2.2 Arduino Compatibility
For Arduino boards, connect the IIC pins as follows:
- GND to Arduino GND
- VCC to Arduino 3.3V or 5V (depending on your module's specific voltage tolerance and Arduino model)
- SCL to Arduino A5 (for Uno/Nano) or SCL pin (for Mega/ESP32/ESP8266)
- SDA to Arduino A4 (for Uno/Nano) or SDA pin (for Mega/ESP32/ESP8266)
Keypad pins will connect to digital I/O pins on your Arduino, configured as inputs with pull-up resistors (internal or external) for reading key presses.

3.2.3 STM32F103C8T6 Compatibility
For STM32F103C8T6 boards, connect the IIC pins as follows:
- GND to STM32 GND
- VCC to STM32 3.3V or 5V
- SCL to STM32 B6 (or other designated SCL pin)
- SDA to STM32 B7 (or other designated SDA pin)
Keypad pins will connect to digital I/O pins on your STM32 board.

4. Operation
Operating this module involves programming your microcontroller (e.g., Arduino, Raspberry Pi) to communicate with the OLED display via IIC and read input from the integrated keypad.
4.1 OLED Display Control
The OLED display uses the SSD1116 (or SH1116/SH1315) driver IC. You will typically use a library compatible with these drivers for your chosen microcontroller. Common libraries for Arduino include Adafruit GFX Library and Adafruit SSD1306/SH1106 Library (often compatible with similar drivers). These libraries provide functions for:
- Initializing the display
- Drawing text, shapes, and bitmaps
- Setting cursor position
- Clearing the display
- Updating the display buffer
Refer to the documentation of your chosen library for specific API calls and examples.
4.2 Keypad Input
The integrated keypad is typically a matrix keypad. To read input, you will need to implement a keypad scanning routine in your code. This involves:
- Setting row pins as outputs and column pins as inputs with pull-up resistors.
- Iterating through each row, setting it LOW while keeping others HIGH.
- Reading the state of each column. If a column pin goes LOW, a key in that row and column is pressed.
- Debouncing the key presses to prevent multiple readings from a single press.
Libraries like the Arduino Keypad Library can simplify this process. For the 4-key module, the keys are typically independent and can be read as individual digital inputs.


5. Maintenance
The Estardyn OLED Display with Keypad Module is a robust electronic component. Proper care will ensure its longevity.
- Handling: Always handle the module by its edges to avoid touching the display surface or sensitive electronic components.
- Cleaning: If necessary, gently wipe the display surface with a soft, lint-free cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the module in a dry, anti-static environment, away from direct sunlight and extreme temperatures.
- Power Supply: Ensure the power supply voltage is within the specified range (2.2V - 5.5V) to prevent damage.
- ESD Protection: Take appropriate electrostatic discharge (ESD) precautions when handling the module to prevent damage to sensitive components.
6. Troubleshooting
If you encounter issues with your OLED display and keypad module, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Display is blank or shows garbage |
|
|
| Keypad not responding |
|
|
| Intermittent display or key issues |
|
|
7. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. However, general tips for working with OLED displays and keypads include:
- Start Simple: Begin with basic "Hello World" examples for the OLED and simple key press detection for the keypad before integrating complex logic.
- Library Compatibility: Be aware that while many OLED libraries are compatible, some specific driver ICs (like SH1116 vs. SSD1306) might require different library versions or initialization parameters. Check the module's markings or product description for the exact driver.
- Power Considerations: While OLEDs are power-efficient, ensure your microcontroller can supply sufficient current, especially if powering other components.
- Code Examples: Search online forums and communities (e.g., Arduino forums, Raspberry Pi forums) for code examples specific to 128x64 IIC OLEDs and matrix keypads.
8. Warranty and Support
For technical support, troubleshooting assistance, or warranty inquiries, please contact the seller or manufacturer directly through the platform where the product was purchased. Provide your order details and a clear description of the issue to facilitate a quicker resolution.
This product is intended for hobbyist and educational use. Users are responsible for ensuring proper integration and safe operation within their projects.