JANSNO X50

Contents

JANSNO X50 Electric Bike User Manual

Model: X50 | Brand: JANSNO

JANSNO X50 Electric Bike

The JANSNO X50 Electric Bike, a 48V17AH Fat Tire 20' Off Road Mountain Ebike.

Introduction

About This Manual

This manual provides essential information for the proper assembly, operation, and maintenance of your new JANSNO X50 Electric Bike. Reading this manual thoroughly before your first ride will help you understand its features, maximize performance, and ensure your safety. Your new bicycle was partially assembled at the factory and then partially disassembled for shipping. It may arrive fully assembled or in a partially disassembled state. The instructions herein will guide you through preparing your bicycle for years of enjoyable cycling.

It is crucial that your initial ride on your new bicycle occurs in a controlled environment, free from vehicular traffic, obstacles, and other cyclists.

General Warning

Bicycling is an inherently hazardous activity. Proper maintenance is your responsibility and helps mitigate the risk of injury. This manual contains numerous warnings and cautions regarding the consequences of failing to maintain or inspect your bicycle. Many warnings indicate that "you may lose control and fall." Since any fall can result in serious injury or even death, this manual does not repeatedly state the potential for injury or death where the risk of falling is mentioned.

A Special Note for Parents

Bicycle accidents involving children are a serious concern. As a parent or guardian, you are responsible for the activities and safety of your minor child. This includes ensuring the bicycle is properly fitted, in good repair, and safe operating condition. Both you and your child must learn, understand, and obey all applicable local motor vehicle, bicycle, and traffic laws, as well as common-sense rules for safe bicycling. Please read this manual before allowing your child to ride the bicycle. Always ensure your child wears an ANSI, ASTM, SNELL approved bicycle helmet when riding.

Safety Information

Helmet Safety

HELMETS SAVE LIVES!!!

  • ALWAYS WEAR A PROPERLY FITTED HELMET WHEN YOU RIDE YOUR BICYCLE.
  • DO NOT RIDE AT NIGHT. CPSC RECORDS SHOW THAT ABOUT 35% OF BICYCLE RELATED DEATHS OCCUR AFTER DARK.
  • AVOID RIDING IN WET CONDITIONS.
  • CPSC RECORDS SHOW THAT ABOUT 65% OF INJURIES HAPPEN TO CHILDREN UNDER 15 YEARS OF AGE, RIDE ONLY WITH ADULT SUPERVISION.
  • FOR YOUR SAFETY, WHEN RIDING, PLEASE WEAR A HELMET AND PROTECTIVE GEAR, AND PLEASE OBEY LOCAL LAWS AND REGULATIONS.
Correct helmet fitting

CORRECT FITTING: Ensure your helmet covers your forehead.

Incorrect helmet fitting

INCORRECT FITTING: Forehead is exposed and vulnerable to serious injury.

Factors to Maximize the Range of Your Electric Bicycle

To get the most out of your electric bicycle's range, consider the following factors:

  • Rider Input: The more you pedal, the further you can travel. Continuous riding, as opposed to frequent stopping and starting, yields the greatest range.
  • Elevation Gain: Flatter terrain results in greater travel distance.
  • Weather: Cold weather can negatively impact battery capacity.
  • Wind: Riding with a tailwind increases distance, while riding into a headwind decreases it.
  • Terrain: Smoother terrain (e.g., roadways) allows for greater travel distance compared to rougher surfaces (e.g., fire roads).
  • Rider Weight: A lighter rider results in less battery drain and thus greater travel distance.
  • Bicycle Maintenance: A properly maintained bicycle will achieve the greatest possible range.
  • Tire Pressure: Properly inflated tires reduce rolling resistance and make pedaling easier.
  • Batteries: Properly charged and maintained batteries provide the greatest range. Batteries stored in cold areas (below 50°F / 10°C) will show reduced range. Batteries not kept in optimum condition will also show reduced range and run time.

Setup & Assembly

Getting Started

Open the carton from the top and carefully remove the bicycle. Remove all straps and protective wrapping. Inspect the bicycle and all accessories for any missing parts. It is recommended to lubricate threads and all moving parts in the parts package before installation. Do not discard packing materials until assembly is complete to ensure no required parts are accidentally discarded.

Note: Your bicycle may have components that differ slightly in style from those illustrated.

JANSNO X50 Electric Bike ready for assembly

The JANSNO X50 Electric Bike as it appears before full assembly.

Bicycle Components Overview

Diagram of JANSNO X50 Electric Bike components

Key components of the JANSNO X50 Electric Bike, including Saddle, Rear Turn Light, Shock Absorber, Speed Flywheel, LCD Screen, Double Suspension Fork, Pedal, Chain, Crankset, Accelerator, Headlight, Turn Signal, Removable Battery, and Front Disc Brake.

Pedals & Crank Set Installation

Identify the pedals by the letters "R" for right and "L" for left, stamped on each pedal spindle. Thread each pedal by hand to prevent stripping the threads. The right pedal attaches to the chainwheel side crank arm with a right-hand (clockwise) thread. The left pedal attaches to the other crank arm with a left-hand (counter-clockwise) thread. Tighten with a 15mm narrow open-ended wrench.

After installing the pedals, remove the dust caps from the center of each crank arm. Securely tighten the spindle nuts (approximately 350 in.lbs.) using a 14mm socket wrench or an 8mm Allen wrench, depending on the style, then replace the dust caps.

WARNING: Attachment of an incorrect pedal into a crank arm can strip pedal threads and cause irreparable damage. Before your first ride, please check to ensure your pedals are attached correctly.

Pedal and crank set installation diagram

Diagram illustrating the correct threading direction for left (L) and right (R) pedals, and the location of the dust cap.

Wheel Installation

Front Wheel Bolt-on Installation

  1. Ensure the brakes are loose enough for the wheel to pass through the brake pads easily.
  2. Place the wheel into the fork dropouts.
  3. Install retaining washers with the raised lip pointing towards the fork, inserting them into the small hole of the fork blade. (Note: Some bikes may have step retaining washers instead of standard retaining washers.)
  4. Install and tighten the axle nut. Ensure the wheel is centered between the fork blades.
  5. Spin the wheel to confirm it is centered and clears the brake shoes. Tighten the brakes if necessary.

CRITICAL WARNING: It is very important to check the front wheel connection to the bicycle. Failure to properly tighten may cause the front wheel to dislodge.

Front disc brake assembly

Close-up of the front disc brake assembly.

Rear disc brake assembly

Close-up of the rear disc brake assembly.

Rear Wheel Bolt-on Installation

  1. If your bicycle has rim brakes, ensure they are loose enough for the wheel to pass through the brake pads easily. For disc brakes, no adjustment is required.
  2. Place the wheel into the frame dropouts.
  3. Slide a washer onto each side of the axle.
  4. Install and tighten the axle nuts. Ensure the wheel is centered in the frame. This may be easier with the bike turned upside-down.
  5. Spin the wheel to confirm it is centered and clears the brake shoes. Tighten the brakes if necessary.

WARNING: Tighten both rear wheel axle nuts securely. Failure to do this may cause the rear wheel to dislodge from the frame dropouts, resulting in serious damage or injury.

Periodically, disassemble the mechanism from the bicycle and inspect for any wear or damage, replacing if necessary. When reinstalling, ensure connections are made properly.

Rear Wheel Bolt-on Removal

  1. If the bicycle has rim brakes, ensure they are loose enough for the wheel to pass through the brake pads easily. For disc brakes, no adjustment is required.
  2. Most bikes have a plug or quick-disconnect box on the seat stay or chain stay. These allow the motor to be easily disconnected from the controller. Undo the single large plug or open the black plastic box and undo the five plugs inside.
  3. With the bicycle in a stand or upside-down, loosen the axle nuts and then remove the wheel from the bicycle.

Disc Brakes - Tektro

  1. Check the tightness of the six disc mounting bolts holding the brake rotor onto the wheel. If you need to remove these bolts, use a thread-locking compound when re-installing them.
  2. Ensure the two bolts securing the caliper adaptor bracket to the fork are tight.
  3. Thread the brake cable through the caliper as shown and secure it with the cable fixing bolt.
  4. Loosen the two caliper mounting bolts enough to allow the brake caliper to float freely.
  5. Install the wheel, ensuring the brake rotor fits into the slot in the caliper. Center the caliper around the brake rotor, then tighten the caliper mounting bolts.
  6. Using the inner pad adjusting bolt, adjust the inside brake pad so it is as close as possible to the rotor without rubbing.
  7. Using the caliper barrel adjustor, adjust the outside brake pad so it is as close as possible to the rotor without rubbing.
Disc brake components diagram

Diagram showing Caliper Barrel Adjustor, Cable Fixing Bolt, Caliper Adaptor Bracket Bolts, and Caliper Mounting Bolts.

Disc brake pads close-up

Close-up view of disc brake pads.

WARNING: Brake rotors get hot! Severe injury could result from contact with the hot rotor. Mind your legs, as well as your hands.

IMPORTANT: Disc brakes require breaking in. Ride and use the brakes gently for about 13 miles before using them in downhill conditions, for sudden stops, or any other serious braking. The brake system's performance will change during the wear-in process. Clean the disc brake before the first ride using rubbing alcohol. NEVER use oil or similar products to clean your disc brake system. Avoid touching the rotor (disc) with your fingers at any time, as naturally oily fingers can contaminate the rotor and/or brake pads and diminish braking effectiveness.

Derailleur Systems

The derailleur system, including front and rear derailleurs, shift levers, and control cables, must function correctly for smooth gear shifting.

Rear Derailleur Adjustment

Begin by shifting the rear shifter to the largest indicated number. Loosen the cable from the rear derailleur cable anchor bolt and place the chain on the smallest sprocket. Adjust the High limit screw so the guide pulley and the smallest sprocket are vertically aligned. Re-tighten the cable, pull out any slack, and securely re-tighten the anchor bolt. Shift through the gears to ensure each gear is achieved quietly and without hesitation. If necessary, use the barrel adjuster to fine-tune the cable tension:

  • Turning clockwise loosens cable tension and moves the chain away from the wheel.
  • Turning counter-clockwise tightens cable tension and directs the chain towards the wheel.
Rear wheel and derailleur system

Close-up of the rear wheel and Shimano 7-speed derailleur system.

Final Check After Assembly

After all adjustments, shift through every gear several times at varying speeds to confirm correct adjustments and identify any issues. Refer to relevant sections for troubleshooting. Check tire pressure and inflate to the recommended PSI on the sidewall. Ensure the kickstand operates smoothly and its bolt is tight. Finally, inspect the bicycle to confirm all accessories are attached and all quick releases, nuts, and bolts are securely tightened.

WARNING: Never inflate a tire beyond the maximum pressure marked on the tire's sidewall. Exceeding recommended pressure can cause the tire to blow off the rim, damaging the bicycle and potentially injuring the rider and bystanders.

Installation Procedures (Handlebar, Battery, Power)

  1. Handlebar Installation: When installing the handlebar, be careful not to tear off the waterproof wire connector.
  2. Battery Installation: Ensure the battery is firmly in place by pressing it down hard. The battery key can be used to lock the battery. Then, open the battery in the upper right corner using the red switch.
  3. Power Activation: Turn the power door key to the right until it cannot be pulled out. After these three steps, the headlights and turn signals should function normally.
  4. Instrument Power: Long press the middle button on the instrument to power it on. If the above steps do not work, check if the connector on the handlebar's waterproof line is loose. If still no reaction, check if the controller terminal is plugged in.

NOTE: For European law, please put on a 250W motor sticker.

Operating Instructions

Handlebar Controls Overview

Handlebar controls diagram

Diagram showing the handlebar controls: LCD Screen Display, Brake Cable, Power Off Switch Line, TYPE-C port, L&R turn signal switch, Horn, Electric Speed Button, Gear Increase Button, Brake Lever, Accelerator, and Gear Reduction Button.

Smart LCD Display

The HD LCD display provides accurate battery speed and mileage. The instrument backlight is clearly visible day and night. It shows real-time speed, power regulation, ODO (odometer), power display, and date view.

Smart LCD display showing bike metrics

The smart LCD display showing speed, mileage, power regulation, ODO, power display, and date view.

TAG (Twist and Go) Function

Before riding, use NFC to unlock the monitor or enter a password. Then, start riding as you would a regular, non-motor-assisted bicycle. Once you begin riding, slowly twist the throttle (on equipped models) towards you. The more you twist the throttle, the more motor power will be applied to the wheels. You may feel the pedals become "lighter" as the motor assists. The speed range is typically 13-30 mph (20-48 km/h), varying with load changes.

The new upgrade adds NFC functionality. The default unlock password for the instrument is 0000.

How to Reset the Power-on Password:

  1. Press and hold '+' and '-' buttons to enter setting mode. Press the middle button to adjust to '22'.
  2. Press '+' to adjust to '0' to cancel the password.
  3. To set a custom password: Adjust to '22' as in step 1. Press '+' to adjust to '1'. You will see a flashing number. Press '+' to set your desired 4-digit password, pressing the middle button to confirm each digit.
  4. Finally, press and hold '+' and '-' to exit the setting mode.

IMPORTANT: Please don't change too many parameters to avoid setting errors and restoring factory settings. Normally, you only need to adjust the following parameters after receiving the bike:

  • P01: Brightness setting (1 for darker, 3 for lighter).
  • P02: Set to 1 to switch to MPH.
  • P03: Select 48V.
  • P06: Setting 20.

Other settings do not need to be changed. If you have set up wrong settings and need to reset, follow instructions in P16 to reset the system.

Comparison of old vs new display controls

Comparison of previous and upgraded display controls, highlighting the 'cancel light button' and the method to turn on headlights by long-pressing the 'Meter +' button on the upgraded version.

Video Demonstration

This video demonstrates the battery installation and throttle operation of the JANSNO X50 Electric Bike.

Maintenance

Safety Checklist (Before Every Ride)

Perform the following checks before each ride:

  1. Brakes:
    • Ensure front and rear brakes function properly.
    • Check brake shoe pads for wear and correct positioning relative to rims.
    • Verify brake control cables are lubricated, adjusted, and free from obvious wear.
    • Ensure brake control levers are lubricated and securely fastened to the handlebar.
  2. Wheels and Tires:
    • Inflate tires to the recommended limit shown on the sidewall.
    • Check tires for tread, bulges, or excessive wear.
    • Ensure rims run true without wobbles or kinks.
    • Verify all wheel spokes are tight and unbroken.
    • Check that axle nuts are tight. If equipped with quick release axles, ensure locking levers are correctly tensioned and in the closed position.
  3. Steering:
    • Ensure handlebar and stem are correctly adjusted, tightened, and allow proper steering.
    • Verify handlebars are set correctly in relation to the forks and direction of travel.
    • Check that the headset locking mechanism is properly adjusted and tightened.
    • If handlebar end extensions are fitted, ensure they are properly positioned and tightened.
  4. Chain:
    • Ensure the chain is oiled, clean, and runs smoothly.
    • Exercise extra care in wet or dusty conditions.
  5. Bearings:
    • Ensure all bearings are lubricated, run freely, and show no excess movement, grinding, or rattling.
    • Check headset, wheel, pedal, and bottom bracket bearings.
  6. Cranks and Pedals:
    • Ensure pedals are securely tightened to the cranks.
    • Ensure cranks are securely tightened to the axle and are not bent.
  7. Derailleurs:
    • Check that front and rear mechanisms are adjusted and function properly.
    • Ensure shift and brake levers are attached to the handlebar.
    • Ensure derailleurs, shift levers, and shift and brake cables are properly lubricated.
  8. Frame and Fork:
    • Check that the frame and fork are not bent or broken.
    • If bent or broken, they should be replaced.
  9. Accessories:
    • Ensure all reflectors are properly fitted and not obscured.
    • Ensure all other fittings on the bike are properly and securely fastened and functioning.
    • Ensure the rider is wearing a helmet.
  10. Motor Drive Assembly and Throttle:
    • Ensure all motor drive components are correctly mounted and functioning properly.
  11. Battery Pack:
    • Ensure the batteries are in good operating condition and kept fully charged.

Battery Care and Information

Proper battery maintenance maximizes lifespan and capacity. JANSNO X50 batteries are warranted from the date of purchase only if properly cared for. Li-Ion batteries are used in all JANSNO electric bicycles and scooters, and are user-friendly when maintained correctly.

Care Guidelines:

  • Initial Charge: Fully charge batteries immediately upon receipt and after each use for the recommended charge times.
  • Recommended Charge Time: Li-Ion batteries require 4-6 hours. For a complete 100% charge, leave the battery on the charger for one full hour after the charger indicator light turns green.
  • Avoid Overcharging: Never charge batteries for longer than 24 hours.
  • Partial Discharge/Charge: Li-Ion batteries do not have a "memory." Partial discharge/charge cycles will not harm the battery's capacity or performance.
  • Temperature: The rated output capacity is measured at 77°F (25°C). Variations in temperature will alter performance and shorten life. High temperatures particularly reduce overall battery life and run time.
  • Environmental Responsibility: Recycle old batteries at a local battery-recycling center. Do not dispose of them in regular garbage.

WARNING: Do not charge the battery indoors!

Battery Safety: Storage & Charging

Storage Guidelines:

  • Temperature Control: Store batteries in cool, dry environments (10–25°C / 50–77°F). Avoid garages/basements in extreme climates.
  • Charge Level: Maintain 40–60% charge for long-term storage (>1 month). Check every 2 months; recharge to 50% if below 30%.
  • Location: Keep away from direct sunlight, heaters, or flammable materials. Never store in living spaces or escape routes.

Safe Charging Practices:

  • Avoid Overnight Charging: Unplug immediately after full charge. Use timers/smart plugs to prevent overcharging.
  • Environment: Charge on non-flammable surfaces (e.g., concrete), in ventilated areas. Never cover batteries during charging.
  • Charger Use: Only use the manufacturer-provided charger. Mismatched chargers risk overheating or fire.

Emergency Response to Battery Abnormalities:

Stop using immediately if any of these occur:

  • Overheating (Battery feels hot):
    • Disconnect from the bike/charger.
    • Move outdoors to a concrete/metal surface away from flammables.
    • Allow natural cooling—do NOT use water/ice.
  • Leaking or Strange Odors:
    • Evacuate the area—inhaled fumes are toxic.
    • Ventilate the space; wear a mask if handling.
    • Place the battery in a fireproof container (e.g., metal bucket with sand).
  • Swelling/Deformation:
    • Do not puncture, compress, or charge.
    • Isolate the battery outdoors; contact professional disposal services.
  • Smoke or Fire:
    • Call emergency services immediately.
    • Use Class D fire extinguishers (for metal fires) or smother with sand—never use water.

CRITICAL REMINDERS: Never repair damaged batteries yourself. Replace immediately if abnormalities persist after cooling. Dispose of expired/damaged batteries via certified recycling centers.

Key Warning: Ignoring these protocols may cause fire, explosion, or toxic exposure. Prioritize safety over convenience.

Lubrication Schedule

Regular maintenance ensures smooth running, longer component life, and safer riding. The more you ride, the more frequently maintenance will be required. You should be able to accomplish most tasks; if you need assistance, consult a bicycle specialist.

Frequency Component Lubricant How to Lubricate
Weekly Chain Chain Lube or Light Oil Brush On or Squirt
Derailleur Pulleys Chain Lube or Light Oil Brush On or Squirt
Derailleurs Oil Oil Can
Brake Calipers, Brake Levers Oil 3 drops from oil can, 2 drops from oil can
Monthly Shift Levers Lithium Based Grease Disassemble
Every Six Months Freewheel Oil 2 squirts from oil can
Brake Cables Lithium Based Grease Disassemble
Yearly Bottom Bracket Lithium Based Grease Disassemble
Pedals Lithium Based Grease Disassemble
Derailleur Cables Lithium Based Grease Disassemble
Wheel Bearings, Headset, Seat Post Lithium Based Grease Disassemble

Drivetrain and Pedals Inspection

The drivetrain includes all parts that transmit power to the rear wheel: pedals, chain, chainwheel, crank set, and freewheel.

Pedals Inspection:

Pedals should be inspected monthly. Pay attention to the following:

  • Tightness: Check for correct tightness into the crank arms. Loose pedals are dangerous and can cause irreparable damage to the cranks.
  • Bearings: Check that pedal bearings are properly adjusted. Move pedals up and down, right to left, and rotate them by hand. If you detect looseness or roughness, adjustment, lubrication, or replacement is required.
  • Reflectors: Ensure front and rear pedal reflectors are securely fitted.
  • Toe Clips (if fitted): Ensure toe clips are securely attached.

WARNING: Never ride with loose pedals.

Troubleshooting

Common Mechanical Issues

Problem Possible Cause Remedy
Gear shifts not working properly Derailleur cables sticking/stretched/damaged; Front or rear derailleur not adjusted properly; Indexed shifting not adjusted properly Lubricate/tighten/replace cables; Adjust derailleurs; Adjust indexing
Slipping chain Excessively worn/chipped chainring or freewheel sprocket teeth; Chain worn/stretched; Stiff link in chain; Non-compatible chain/chainring/freewheel Replace chainring, sprockets and chain; Replace chain; Lubricate or replace link; Seek advice at a bicycle shop
Chain jumping off freewheel sprocket or chainring Chainring out of true; Chainring loose; Chainring teeth bent or broken; Rear or front derailleur side-to-side travel out of adjustment Re-true if possible, or replace; Tighten mounting bolts; Repair or replace chainring/set; Adjust derailleur travel
Constant clicking noises when pedaling Stiff chain link; Loose pedal axle/bearings; Loose bottom bracket axle/bearings; Bent bottom bracket or pedal axle; Loose crankset Lubricate chain /Adjust chain link; Adjust bearings/axle nut; Adjust bottom bracket; Replace bottom bracket axle or pedals; Tighten crank bolts
Grinding noise when pedaling Pedal bearings too tight; Bottom bracket bearings too tight; Chain fouling derailleurs; Derailleur jockey wheels dirty/binding Adjust bearings; Adjust chain line; Clean and lubricate jockey wheels
Freewheel does not rotate Freewheel internal pawl pins are jammed Lubricate. If problem persists, replace freewheel
Brakes not working effectively Brake blocks worn down; Brake blocks/rim greasy, wet or dirty; Brake cables are binding/stretched/damaged; Brake levers are binding; Brakes out of adjustment Replace brake blocks; Clean blocks and rim; Clean/adjust/replace cables; Adjust brake levers; Center brakes
When applying the brakes they squeal/squeak Brake blocks worn down; Brake block toe-in incorrect; Brake blocks/rim dirty or wet; Brake arms loose Replace blocks; Correct block toe-in; Clean blocks and rim; Tighten mounting bolts
Knocking or shuddering when applying brakes Bulge in the rim or rim out of true; Brake mounting bolts loose; Brakes out of adjustment; Fork loose in head tube True wheel or take to a bike shop for repair; Tighten bolts; Center brakes and/or adjust brake block toe-in; Tighten headset
Wobbling wheel Axle broken; Wheel out of true; Hub comes loose; Headset binding; Hub bearings collapsed; QR mechanism loose Replace axle; True wheel; Adjust hub bearings; Adjust headset; Replace bearings; Adjust QR mechanism
Steering not accurate Wheels not aligned in frame; Headset loose or binding; Front forks or frame bent Align wheels correctly; Adjust/tighten headset; Take bike to a bike shop for possible frame realignment
Frequent punctures Inner tube old or faulty; Tire tread/casing worn; Tire unsuited to rim; Tire not checked after previous puncture; Tire pressure too low; Spoke protruding into rim Replace Inner tube; Replace tire; Replace with correct tire; Remove sharp object embedded in tire; Correct tire pressure; File down spoke

Instrument Ebike Error Status Code Meaning

Status Code State Meaning Reason
E00 Normal status After the failure of the vehicle during this operation was repaired
E02 Brake failure Try unplugging the left brake plug and see if E02 disappears. If it does, unplug the right brake plug. If it disappears, confirm which brake lever is the problem and contact professional customer service for replacement.
E06 Battery undervoltage Battery drain
E07 Motor failure ① The motor wire plug is loose; ② The motor is damaged.
E08 Handlebar failure ① The turning handle is back to the original position before starting up; ② The plug is loose; ③ The turning handle is damaged.
E09 Controller failure Controller is damaged
E10 Communication (reception) failure ① Check the condition of the plug; ② The controller is damaged; ③ The electric door lock of the meter is damaged; ④ Check whether all the components that use the 5V voltage are damaged.
E11 Communication (send) failure ① Check the plug condition; ② The meter is damaged.
E30 Communication fail The P20 setting item is set to 0 (when this fault occurs in the No. 2 protocol)

Specifications

JANSNO X50 dimensions and weight

Dimensions and weight references for the JANSNO X50 Electric Bike, including recommended height, ebike weight, and maximum load.

JANSNO X50 Electric Off-Road Bike features

Key features of the JANSNO X50 Electric Off-Road Bike: 48V 17AH Lithium battery, 50km-60km max range, 20"x4.0 fat tire, 7-speed driving gear, USB charge port, and approximately 6-8 hours charging time.

Attribute Value
Brand Name JANSNO
Model Number x50-17
Wattage 200 - 250w
Max Speed <25km/h
Range per Power 31 - 60 km
Power Supply Lithium battery
Voltage 48V
Power Source Lithium battery
Origin Mainland China
Wheel Size 20“
Age Range (Description) Adult
Number of Speeds 7
Maximum Weight Recommendation 120kg (330lbs)
Suspension Type Bidirectional
Included Components Mobile phone holder, ring lock, air pump, installation tools
Brake Style Disc Brake
Cycling environment Urban leisure, mountain
Charging Time 6-9 hours
Battery 48V17AH
Removable battery yes
Rated Passenger Capacity One Seat

User Tips

  • Unboxing: Upon receiving your JANSNO X50, carefully check the package contents. It should include the bike, a tire inflation pump, a multi-tool for assembly, a smartphone holder, and an anti-theft lock.
  • Assembly: If you encounter any damaged parts during assembly, particularly critical components like the front wheel fixing rod, contact customer support immediately for replacements.
  • Tires: The bike comes with fat, knobby tires ideal for off-road use. If you plan to primarily ride on paved roads, you might consider exploring options for smoother tires to optimize your riding experience.
  • Accessories: The JANSNO X50 is designed to accommodate additional accessories such as a rear carrier or a front basket, allowing for customization based on your needs.
  • Assembly Videos: If you need further assistance with assembly, check the official website or contact support for assembly videos.

Warranty & Support

For any questions regarding assembly, replacement parts, or after-sales service, please contact JANSNO through the official channels:

  • Official Website: www.jansno.com
  • Business E-mail: bp@jansno.com
  • After-sales Service E-mail: help@jansno.com
  • Address: Room 803B, Building 1, Kanglicheng, No. 66 Pingji Avenue, Shanglilang Community, Nanwan Subdistrict, Longgang District, Shenzhen, Guangdong Province, China

You can also scan the following QR codes for quick access to support and videos:

QR code for After-sales videos

After-sales videos

QR code for Jansno Support (Scan with camera or browser)

Jansno Support (Scan with camera or browser)

QR code for Jansno Support (Scan with WhatsApp)

Jansno Support (Scan with WhatsApp)

A user manual in PDF format is also available for download: JANSNO X50 User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.