1. Introduction
The DAKEFPV VTX 3.3G 4W is a high-power FPV video transmitter designed for long-range applications in racing drones and other RC aircraft. It features a robust CNC shell for heat dissipation and protection, a built-in brushless fan for active cooling, and multiple power output options. This manual provides essential information for the safe and effective setup, operation, and maintenance of your VTX.
2. Specifications
| Parameter | Value |
|---|---|
| Model | DAKE VTX 4W |
| Frequency Band | 3.3-3.4GHz |
| Input Voltage | DC 7-50V (2-12S BAT) |
| Output Voltage | 5V@1.9A |
| Output Power | 4W (Adjustable: 1.6W, 2.5W, 3W, 5W, 10W options may be available depending on model variant) |
| Agreement | IRC Tramp |
| Weight | 16g |
| Size | 37*28.7*14mm |
| Material | Metal (High-strength CNC shell) |
| Heat Dissipation | Built-in micro brushless fan |
Kind reminder: All dimensions are marked with reasonable errors, and everything is subject to the actual product.
3. Setup
3.1 Component Identification
3.2 Wiring Instructions
Carefully follow the wiring diagrams below to connect your VTX to your flight controller and power source.
Important Warnings:
- Always install the antenna before use. Operating the VTX without an antenna can cause permanent damage.
- To prevent overheating, ensure continuous air circulation and a good ventilation environment.
- If used in a small space, install a cooling 3.5V output terminal only for the camera and cooling fan.
- Do not use the power input terminal to connect the battery to the 5V output port, otherwise the aircraft will be damaged.
- The 5V output terminal is only used for cameras and cooling fans. Do not connect the power input/battery to the 5V output port, otherwise the aircraft will be damaged.
4. Operating Instructions
4.1 Channel, Band, and Power Setting
The VTX features a single button for controlling power, band, and channel settings. Indicator LEDs (Red for Power, Green for Band, Blue for Channel) provide visual feedback.
-
How to set Channel:
Press and hold the button for 2 seconds to enter the Channel Selection mode. The Blue LED will flash. Short press the button to cycle through channels CH1 to CH8. The number of flashes corresponds to the channel number (e.g., 1 flash for CH1, 8 flashes for CH8).
LED Color CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 Blue Flash 1X Flash 2X Flash 3X Flash 4X Flash 5X Flash 6X Flash 7X Flash 8X -
How to set Band:
Press and hold the button for 2 seconds to enter the Band Selection mode. The Green LED will flash. Short press the button to cycle through available bands (e.g., Boscam_A, Boscam_B, FATSHARK, Race Band, etc.). The number of flashes corresponds to the band index.
LED Color Boscam_A Boscam_B Boscam_E FATSHARK Race Band Boscam_D LOWRACE Boscam_X Green Flash 1X Flash 2X Flash 3X Flash 4X Flash 5X Flash 6X Flash 7X Flash 8X -
How to set Power:
Press and hold the button for 2 seconds to enter the Power Selection mode. The Red LED will flash. Short press the button to cycle through power levels (e.g., 25mW, 200mW, 800mW, 1600mW, Pit Mode). The number of flashes corresponds to the power level.
LED Color 25mW 200mW 800mW 1600mW Pit Red Flash 1X Flash 2X Flash 3X Flash 4X Flash 5X
4.2 Frequency Table (3.3G 16CH)
| Band | CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
|---|---|---|---|---|---|---|---|---|
| Band 1 (A) | 3320 | 3345 | 3370 | 3395 | 3420 | 3445 | 3470 | 3495 |
| Band 2 (B) | 3310 | 3335 | 3360 | 3385 | 3405 | 3430 | 3455 | 3480 |
5. Maintenance
5.1 Heat Dissipation
The DAKEFPV VTX is equipped with a built-in micro brushless fan and a high-strength CNC aluminum alloy shell for active heat dissipation. Proper cooling is crucial for the longevity and performance of your VTX, especially at higher power outputs.
- Ensure the VTX is mounted in a location with adequate airflow. Avoid enclosing it completely without ventilation.
- Regularly check the fan for any obstructions (dirt, debris) and clean gently if necessary.
- The CNC shell also aids in passive cooling; avoid covering it with materials that would trap heat.
5.2 General Care
- Keep the VTX clean and free from dust and moisture.
- Avoid exposing the VTX to extreme temperatures or direct sunlight for prolonged periods.
- Handle all wiring and connectors with care to prevent damage.
6. Troubleshooting
-
No Video Signal:
- Ensure the antenna is securely connected to both the VTX and your FPV goggles/receiver.
- Verify that the VTX is powered on and receiving adequate voltage (7-50V).
- Check that your FPV goggles/receiver are set to the correct band and channel as the VTX.
- Inspect the video signal wire connection between the camera, VTX, and flight controller.
-
Poor Video Range/Interference:
- Ensure you are using compatible antennas (e.g., RHCP with RHCP).
- Increase the VTX power output if legally permitted in your region.
- Check for sources of electromagnetic interference near the VTX (e.g., ESCs, motors, power cables). Try to separate components.
- Ensure the VTX antenna is not obstructed by carbon fiber or other materials.
- Verify that the VTX is not overheating, as this can reduce performance.
-
VTX Overheating:
- Ensure the VTX has sufficient airflow, especially when operating at higher power levels.
- Check if the internal fan is spinning.
- Reduce the VTX power output if continuous overheating occurs.
- Ensure the VTX is not short-circuited or improperly wired.
-
VTX Not Powering On:
- Check the input voltage to ensure it is within the 7-50V range.
- Verify all power connections are secure and correctly polarized.
- Inspect for any visible damage to the VTX or wiring.
7. User Tips
- Antenna Choice: For optimal long-range performance, consider using high-gain directional antennas on your ground station/receiver, paired with a good omnidirectional antenna on the VTX.
- Power Management: While the VTX supports high power, always use the lowest power setting necessary for your flight environment to minimize heat generation and reduce interference to other pilots.
- Mounting: Mount the VTX away from other sensitive electronics and carbon fiber frames as much as possible to reduce signal degradation and improve heat dissipation.
- IRC Tramp: Utilize the IRC Tramp protocol for convenient VTX control directly from your flight controller's OSD (On-Screen Display) or Betaflight/INAV configurator. This allows for easy channel and power changes without needing to access the VTX button.
8. Warranty and Support
For warranty claims, technical support, or any product-related inquiries, please contact the DAKEFPV Store directly through the platform where you purchased the product. Provide your order number and a detailed description of the issue to facilitate a quicker resolution.
Please note that damage caused by improper installation, misuse, or unauthorized modifications may void the product warranty.