DAKEFPV H743 FC + BLS ESC Stack

Contents

DAKEFPV H743 Flight Controller and ESC Stack User Manual

Brand: DAKEFPV | Model: H743 FC + BLS ESC Stack

1. Introduction

The DAKEFPV H743 Flight Controller and ESC Stack is a high-performance solution designed for advanced RC drone applications. This stack combines a powerful H743 Flight Controller with a robust BLS 4-in-1 Electronic Speed Controller (ESC), offering excellent control and power delivery for your FPV setup. It supports a wide range of battery configurations (6S to 8S) and is compatible with popular firmware like Betaflight, INAV, and ArduPilot.

This manual provides essential information for the proper installation, configuration, and operation of your DAKEFPV H743 stack.

Product overview showing the DAKEFPV H743 Flight Controller and 8S 70A ESC stack components.

2. Package Contents

The DAKEFPV H743 70A 30x30 STACK package typically includes the following items:

Package contents for DAKEFPV H743 70A 30x30 STACK

Package contents for Option 1 - DAKEFPV H743 70A 30x30 STACK, listing components and quantities.

  • DAKEFPV H743 Flight Controller x 1
  • DAKEFPV BLS 70A 4-in-1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 Silicone O-Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1 set
  • M3*8.1mm Silicone Grommets (for ESC) x 1 set
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1

3. Specifications

3.1. Flight Controller (H743)

Flight Controller Specifications Table

Table of Flight Controller specifications.

FeatureDescription
Main Control ChipH743 (better performance than F722)
Supported FirmwareBetaFlight (default), ArduPilot, INAV
Target NameDAKEFPV H743
Motors SupportedUp to 8 motors, plus 4 servos (for X8/Y6/fixed-wing aircraft)
Onboard Flash16MB (for Black Box)
BarometerBuilt-in, real-time altitude sensing
BEC12V 3A + 5V 3A Dual independent BEC
URATs8 groups of idle serial ports
GPS Module PowerPowered by 5.0V
DJI Air Unit InterfaceDirect plug-in compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1
Mounting Holes30.5 x 30.5 mm (4mm hole diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g
GyroscopeDual gyro ICM42688P
Filter Capacitors21 imported Japanese TDK SMD filter capacitors + 1000uF ultra-large capacity
ProtectionTVS protection diode
DAKEFPV H743 Flight Controller Features

Features overview of the DAKEFPV H743 Flight Controller.

3.2. Electronic Speed Controller (BLS 4-in-1 ESC)

ESC Specifications Table

Table of ESC specifications.

FeatureDescription
Product NameDAKE 12S 70A 4 in 1 ESC (Note: Product supports 6S-8S, 70A is max current)
FirmwareBLHeli_S / BlueJay
Battery Input3-8S LiPo
Continuous Current70A x 4
Maximum Current80A x 4 (10 seconds)
Internal TVS DiodeYes, for voltage spike suppression
External Capacitor1000uF high-frequency low-resistance electrolytic capacitor (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Current MeterSupported (Scale=400, Offset=0)
Temperature SensingNot supported
Mounting Holes30.5 x 30.5 mm (4mm hole diameter)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g
ESC Upgrade to 70A

Explanation of the ESC upgrade to 70A, detailing PCB copper thickness, MOS tube upgrade, continuous current, peak current, and aluminum alloy heat sink.

3.3. Stack Dimensions

Dimensions of the DAKEFPV H743 Flight Controller and ESC stack

Dimensions of the DAKEFPV H743 Flight Controller and ESC stack, showing measurements in millimeters.

4. Setup and Installation

4.1. Mounting the Stack

When installing your DAKEFPV H743 stack, adhere to the standard mounting method. The orientation of the gyroscope and motor sequence can be adjusted through software settings. If you opt for an inverted mounting, exercise extreme caution regarding the space between the frame, the Flight Controller (FC), and the Electronic Speed Controller (ESC).

Important Stack Installation Note

Important Stack Installation Note, advising on standard mounting, orientation, and swapping silicon pads to prevent short circuits.

Important Note:

It is critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated in the product documentation. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under warranty.

4.2. Wiring Diagrams

Carefully follow the wiring diagrams below for proper connection of your flight controller and ESC to motors, receiver, GPS, VTX, camera, and other peripherals.

Wiring diagram for DAKEFPV H743 Flight Controller

Comprehensive wiring diagram for the DAKEFPV H743 Flight Controller, showing connections for motors, receiver, GPS, VTX, camera, and LED.

Detailed wiring diagram for DAKEFPV H743 Flight Controller

Detailed wiring diagram for the DAKEFPV H743 Flight Controller, showing connections for GPS, ELRS, VTX, USB Type-C, Buzzer, and LED strip.

BLS 70A 4-in-1 ESC motor connections

Detailed view of the BLS 70A 4-in-1 ESC motor connections (Motor 1-4).

4.3. Firmware Flashing

The DAKEFPV H743 Flight Controller supports BetaFlight (default), ArduPilot, and INAV firmware. To flash new firmware or enter DFU mode for troubleshooting, press and hold the BOOT key while connecting the flight controller to your computer via USB.

5. Operation

5.1. Battery Capacity Indicator

The flight controller features a convenient 4-level battery capacity indicator. Once the battery is connected, you can instantly check the battery level without needing external tools or FPV goggles.

Battery capacity indicator on the flight controller

Diagram illustrating the 4-level battery capacity indicator on the flight controller (FCC, 3V, 5V, 12V).

5.2. LED Light Bar Control

The LED pads located at the corners of the flight controller allow for connection of LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button activates the onboard LED light effect control mode, and short presses toggle between various preset light effects.

LED light bar pads connection and control

Illustration of LED light bar pads connection and control via the BOOT button.

6. Maintenance

To ensure the longevity and optimal performance of your DAKEFPV H743 stack, follow these general maintenance guidelines:

  • Regular Inspection: Periodically check all solder joints and connections for any signs of damage, corrosion, or loose wires.
  • Cleaning: Keep the flight controller and ESC free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning. Avoid using liquids directly on the electronics.
  • Environmental Protection: Protect the stack from moisture, extreme temperatures, and static discharge. Consider conformal coating for enhanced protection in humid or wet conditions.
  • Firmware Updates: Regularly check for and apply the latest firmware updates for Betaflight, ArduPilot, or INAV to benefit from performance improvements and bug fixes.

7. Troubleshooting

If you encounter issues with your DAKEFPV H743 stack, consider the following troubleshooting steps:

  • No Power/Intermittent Power: Double-check all power connections, especially the main battery lead and the capacitor. Ensure the capacitor is correctly installed and not damaged.
  • Short Circuit: Refer to the "Important Stack Installation Note" in Section 4.1. Incorrect installation, particularly regarding silicon pads and USB interface contact, can cause short circuits. Inspect for any physical contact between conductive parts.
  • Flight Controller Not Responding: Ensure the FC is receiving power. Try connecting via USB to a configurator (Betaflight Configurator, etc.) to check if it's detected. If not, attempt to enter DFU mode by holding the BOOT button during USB connection and re-flash the firmware.
  • Motor Issues (No Spin/Incorrect Spin): Verify ESC connections to the motors. Check motor direction in the configurator and ensure ESC calibration is correct. Inspect ESC solder joints for cold joints or bridges.
  • Sensor Malfunctions (Gyro/Accelerometer): Ensure the FC is securely mounted and free from excessive vibrations. Check for any physical damage to the FC board.
  • Peripheral Issues (GPS, VTX, Camera, Receiver): Verify all signal and power connections for the specific peripheral. Check the configurator settings to ensure the correct UARTs and protocols are configured.

8. User Tips

  • Proper Insulation: Always ensure adequate insulation between the FC/ESC and the carbon fiber frame to prevent accidental short circuits. Use the provided silicone grommets and nuts.
  • Silicon Pad Orientation: If you need to change the orientation of the FC or ESC, remember to swap the silicon pads accordingly to maintain proper spacing and prevent the USB port from contacting the ESC.
  • Capacitor Installation: The included 35V 1000uF Low ESR Capacitor is crucial for filtering power spikes and ensuring clean power to the flight controller's gyroscope. Install it correctly on the designated pads.
  • Firmware Choice: While Betaflight is the default, explore INAV or ArduPilot if your drone application requires specific features like GPS navigation or advanced flight modes.
  • Heat Management: The 70A ESC features an aluminum alloy heat sink for efficient heat dissipation. Ensure good airflow around the stack, especially during demanding flights, to prevent overheating.

9. Warranty and Support

For warranty claims, technical support, or further assistance, please contact DAKEFPV directly through their official channels or the retailer from whom you purchased the product. Please note that damage resulting from improper installation, modification, or misuse may void your warranty.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.