Ezonetronics RM-VLV2540F

Contents

Ezonetronics Wireless CarPlay Android Auto Retrofit Kit

Model: RM-VLV2540F

Introduction

Thank you for choosing this Intelligent Car Information System. Our product adds CarPlay and Android Auto to vehicles lacking these features, letting you use them for music, navigation, and more—all via your car's original screen. A seamless upgrade, it bridges your smartphone and in-car display, bringing familiar interfaces without altering your vehicle's factory setup. Easy to integrate, it enhances connectivity safely, turning your existing infotainment system into a smart, intuitive hub. Modernize your drive affordably, leveraging what your car already has.

Safety Precautions

  • Install only by qualified professionals to avoid damaging vehicle electrical systems.
  • Disconnect car battery before installation to prevent short circuits.
  • Ensure all connections are secure and insulated to avoid fire hazards.
  • Do not block airbags, driver visibility, or vehicle controls during installation.
  • Avoid modifying essential vehicle safety systems or wiring.
  • Operate connected devices only when parked; never distract from driving.
  • Regularly check for loose connections or overheating during use.
  • Stop using immediately if unusual smells, sounds, or malfunctions occur.
  • Ensure product usage complies with local traffic laws and regulations.
  • Keep product away from water, extreme temperatures, and direct sunlight when not in use.

Product Features

This intelligent module integrates seamlessly with your vehicle's existing display and controls, offering a range of enhanced functionalities:

  • Apple CarPlay: Connects iPhones to car systems, mirroring key apps for navigation, music, calls, and messages via the car's screen or voice commands. Enables hands-free operation, syncing contacts and playlists, enhancing driving safety and convenience.
  • Android Auto: Connects Android phones to car displays, bringing essential apps safely. Access navigation, music, calls, and messages via voice or touch. Prioritizes driving-focused features for hands-free use, enhancing convenience and safety.
  • Front/Rear/360 Input: Supports video decoding and can be equipped with front view, rear view (with intelligent dynamic trajectory display and radar support), as well as a 360° panoramic view.
  • Built-in 2.4G and 5.8G WIFI for stable connection and Bluetooth 5.0 Technology.
  • Wired/Wireless CarPlay and Android Auto for seamless smartphone integration.
  • Control via steering wheel buttons, central control panel, and touch screen (where applicable), including voice control with "Hey Siri..." or Google Assistant.
  • Supports GPS navigation apps like Google Maps, Waze, and Apple Maps with live traffic information.
  • Built-in DSP for fully adjustable Audio EQ and optimal audio quality.
  • Two RCA inputs allow for adding rear and right PAL/NTSC cameras.
  • Supports HD 360 panoramic cameras and dynamic guidance lines for parking, maintaining OEM parking style.
  • Plug and play, non-destructive installation, free from wire breaks.
  • Switch in/out of CarPlay/Android Auto display at any time using factory controls.
Smart Module Features
Overview of the Smart Module's key features including Bluetooth, CarPlay, Android Auto, and more.
Original Car Functions Integration
The system retains original car functions, allowing control via steering wheel buttons, central control panel, and touch screen.
Intelligent Voice Control
Intelligent voice control for safer driving, supporting Siri and Google Assistant.
Wireless CarPlay Interface
Wireless CarPlay provides freedom and smart control for online maps, music, and phone information.
Wireless Android Auto Interface
Wireless Android Auto allows wired and wireless connection for navigation, media, and voice commands.
Online Navigation Display
Use your favorite navigation app directly on your car's screen.

Compatibility

This retrofit kit is designed for specific Volvo models with a 7-inch screen:

Volvo Model Compatibility Table
Table showing compatible Volvo car models, years, and screen size.
Applicable Volvo Models
Car ModelYearsScreen Size
V402015-20207"
V602015-2019
S60/S60L
XC602015-2017
S80L

Setup and Installation

Installation should only be performed by qualified professionals. Ensure the car battery is disconnected before starting to prevent short circuits.

Package Contents

Package and Accessories
The package includes the main decoder box (139mm x 92mm x 20mm), power cable, LVDS OUT cable, LVDS IN cable, and RCA & USB cable.

Wiring Diagram

Installation Wiring Diagram
Diagram illustrating the connection of the decoder box to the car's head unit, including factory power harness, factory LVDS harness, and original car fiber optic cable.

The main decoder unit connects to the car's existing head unit. The factory power harness and factory LVDS harness are integrated with the decoder box. Ensure all connections are secure.

DIP Settings & Switch

The DIP switches on the decoder box must be set according to your specific car model and screen size. Refer to the table below for the correct settings.

DIP Settings for Volvo Models
Car ModelYearScreen SizeDIP Setting
V402015-20207"2, 4, 5, 6, 7 ON
V602015-20197"2, 5 ON
S60/S60L7"
XC602015-20177"2, 5 ON
S80L7"2, 5, 6, 7 ON

Note: Please ensure that the dial is set to "ON" for the specified numbers. After switching the DIP settings, be sure to restart the decoder for the changes to take effect.

Operating Instructions

Button Control

The system integrates with your vehicle's existing steering wheel and central control panel buttons for seamless operation.

Steering Wheel Button Functions
ButtonOperationFunction
Steering wheel buttons for media controlLong pressSwitch between OEM screen and interface screen (CarPlay/Android Auto)
Steering wheel buttons for media controlShort pressPrevious/Next song
Steering wheel buttons for volume controlShort pressIncrease the volume
Steering wheel buttons for volume controlShort pressDecrease the volume
Central Control Panel Button Functions
ButtonOperationFunction
Central control panel knobSwipe/ClickControl function (navigation, selection)
Central control panel hazard buttonDouble Click Short pressSwitch between OEM screen and interface screen (CarPlay/Android Auto)
Switching between OEM and CarPlay/Android Auto
Long press the 'Previous/Next' button on the car knob to switch between the factory OEM car system and the CarPlay/Android Auto system.

Wireless Connection

The system utilizes wireless CarPlay and Android Auto, supporting audio and video separation. Before using the wireless connection, pair your device via Bluetooth and ensure the vehicle's audio system is set to Bluetooth music mode for optimal connection and audio performance.

Connect Step for Wireless CarPlay/Android Auto:

  1. Turn on your phone's Bluetooth and Wi-Fi, and keep them active.
  2. On your phone, select the Bluetooth device name as “CAR Audio_XXXX”.
  3. A request window will pop up. Confirm pairing and then select “Use CarPlay” or follow the on-screen Android Auto connection process.
Bluetooth Audio Output Steps
Steps for Bluetooth audio output: 1. Pair car Bluetooth, 2. Connect CarPlay, 3. Select sound output to car Bluetooth.

Audio Source

Ensure the sound source on your iPhone is set to the original car radio for proper audio output.

Wireless Android Auto

To connect Wireless Android Auto, go to the Bluetooth settings of the Smart Box. You may need to connect Android Bluetooth or insert a USB cable if wireless connection is not immediately available.

External Settings

Rear View Camera Input

This CarPlay interface supports camera input for clear rearview imagery. Connect the camera as per the guide below.

Optional Aftermarket Rear View Camera
The system supports an optional aftermarket rear view camera for enhanced parking assistance.

Camera Wiring: The rear camera connects to the CAM BVideo input. The front camera (if used) connects to CAM F_Video. Ensure the Rear Camera Detect wire is properly connected.

Radar and Trajectory Settings

To enable reversing trajectory lines and aftermarket radar:

  1. Enter the system settings: Click "Factory mode" > "Advanced mode".
  2. Enter the password "888888".
  3. Go to "MCU setup".
  4. If your aftermarket camera supports reversing trajectory lines, uncheck the A1 box to display them.
  5. If you have an aftermarket radar, uncheck the A2 box to use it.
  6. If you want to connect the front camera, choose the “A3” option.
  7. Return to the previous level and click "Restart system" to apply changes.

Specifications

ParameterValueParameterValue
Operating Voltage9-16V, 14.4V (rated)Storage Temperature-30~+85°C
Operating Temperature-30~+75°CAmbient Humidity≤98% (at 45°C), 65±5% (rated)
Power Consumption Current1A (rated), 3A (Max)Shutdown CurrentCurrent: 300mA (Clock is on)
Quiescent Currentless than 3mACharging Current≤2A; if USB charging current >1A, host machine activates circuit protection to control current within 15A to prevent product damage.

Troubleshooting

8.1 Why will the Box's Bluetooth disconnect?

The following is the working principle of wireless CarPlay: After the device information is confirmed through Bluetooth pairing, a Wi-Fi connection is established to transmit data. To avoid interference, the Bluetooth connection will be disconnected. This is a normal phenomenon.

8.2 I cannot connect the CarPlay, but the Bluetooth is already paired.

Please forget the device Bluetooth and reset Wi-Fi on your iPhone (Settings > General > Transfer or Reset [Device] > Reset > Reset Network Settings).

8.3 Why is the wireless CarPlay not stable?

  1. Ensure that the mounted position of the CarPlay box is not blocked by metal components, as this may impair Wi-Fi signal transmission.
  2. Switch the Wi-Fi channel and then re-enter the CarPlay box. Click: Factory Mode > Connectivity Settings > Hotspot Band > Select 1, 6 or 11, depending on the current region.

User Tips

No specific user tips were available from provided reviews or Q&A content.

Warranty and Support

For any technical issues or support inquiries, please contact our technical support team.

Technical Support: techsupport@anyfar.com

Please refer to the User Manual (PDF) for additional details and diagrams.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.