ETENWOLF ZEPHYR S3C

Contents

ETENWOLF ZEPHYR S3C Portable Air Compressor

User Manual

Model: ZEPHYR S3C | Brand: ETENWOLF

Introduction

Thank you for choosing the ETENWOLF Zephyr S3C Portable Air Compressor. Designed to inflate a wide range of tires and inflatables, this portable power station pump enhances versatility for your outdoor adventures. Please read all instructions and safety warnings before use to reduce the risk of electric shock, fire, and/or serious injury.

Package Content

The following items are included in your ETENWOLF ZEPHYR S3C package:

  • Zephyr S3C Air Compressor x 1
  • Air Chuck x 1
  • Pressure hose x 1
  • Presta valve adapter x 1
  • Inflation needle x 1
  • High-pressure tapered nozzle x 1
  • USB A to C cable x 1
  • User manual x 1
ETENWOLF ZEPHYR S3C Air Compressor and accessories laid out
Image: Contents of the ETENWOLF ZEPHYR S3C package, including the compressor, various nozzles, USB cable, and user manual.

Product Overview

Familiarize yourself with the components and controls of your ETENWOLF ZEPHYR S3C Air Compressor:

Diagram of ETENWOLF ZEPHYR S3C Air Compressor with labeled parts
Image: Front and side view of the ETENWOLF ZEPHYR S3C Air Compressor, highlighting its display, buttons, and ports.

Component List:

No.Component
01Unit button
02Light button
03"-" decrease pressure button
04Mode button
05Start/pause power button
06"+" increase pressure button
07Center display
08LED work light
09Pressure hose
10Type-C port (Input)
11USB-A port (Output)
12Presta valve adapter
13Inflation needle
14High-pressure tapered nozzle
15Manual mode
16Car mode
17Bicycle mode
18Ball mode
19Pressure unit
20Target input value
21Actual pressure value
22Battery level indicator
23Safety alert symbol

Quick Start Guide (Setup)

Follow these steps to quickly set up and begin inflating with your ETENWOLF ZEPHYR S3C:

  1. Remove the pressure hose (09) from its storage channel.
  2. Insert the nozzle (09) clockwise into the object being inflated.
  3. Press the Start/pause power button (05) for three seconds to activate the machine.
  4. Press the Mode button (04) to switch among 4 different modes: Manual mode (15), Car mode (16), Bicycle mode (17), Ball mode (18).
  5. Select the pressure unit between PSI, KPa, and Bar by pressing the Unit button (01).
  6. Press the "-" button (03) to decrease or "+" button (06) to increase the target pressure value.
  7. Press Start/pause power button (05) again to start inflation.
  8. When the inflated item reaches the preset value, the unit will turn off automatically.
Diagram showing inflation steps with dimensions
Image: Visual guide for connecting the hose, starting the compressor, selecting mode, and initiating inflation, including product dimensions.

Notes on Inflation:

  • To stop inflation at any time, press the Start/pause power button (05).
  • The ETENWOLF system will automatically remember the previous pressure settings when the unit is used again.
  • Double check the target input value. Setting a wrong value might lead to an inflated item explosion.
  • After the tire is inflated, the temperature inside the tire will decrease to the ambient temperature, causing the tire pressure to decrease by 0.5 to 1.5 PSI.
  • When finishing pumping a bike tire, don't forget to quickly remove the hose. Otherwise, the losing air may lessen the tire pressure.

Steps to Check Pressure:

  1. Connect the pressure hose (09) to the item.
  2. Press the Start/pause power button (05) to power on.
  3. The center display (07) will show the current pressure.

Operating Instructions

Button Operation Guide

Start/pause power button (05):

  • ON: Long-press Start/pause power button (05) for two seconds to turn on.
  • OFF: When the inflator is turned on, long-press Start/pause power button (05) for two seconds to turn off.

Automatic Shut-off Conditions: The inflator will automatically turn off in the following cases:

  1. 3 minutes of inactivity.
  2. When the charging cable is accidentally disconnected during charging.
  3. 5 minutes of inactivity after being fully charged.
  4. 5 minutes inactivity after being used as a power bank.
  5. When inflating over 5 minutes, but the actual pressure is still below 5 PSI.
  6. When inflating over 5 minutes, but the actual pressure is above 150 PSI.

Preset Pressure Value

The number with the smaller size on the top of the display indicates the target input (20), and the number with the bigger size on the bottom of the display indicates the actual value (21) of the inflated devices.

ModeAdjustable Pressure RangeDefault Pressure
Car mode8-130 PSI35 PSI
Bicycle mode10-145 PSI22 PSI
Ball mode3-16 PSI8.5 PSI
Manual mode3-160 PSI30 PSI

LED Work Light

An LED work light (08) is located on the front of the inflator. To turn the light on, first power on the machine by pressing the Start/pause power button (05) and then press the Light button (02).

Switch between four different light modes:

  • Bright flashlight
  • Ultra-bright flashlight
  • Slow strobe light: light turns on and off.
  • SOS signal: 3 short strobe signals, followed by 3 long strobe signals, and then 3 more short strobe signals, repeated in a loop.

Note: The light will automatically turn off after 1 hour. After the first automatic turn off, you can manually turn on the LED light for the second time. Once manually turned on for the second time, it will not automatically turn off; it must be manually turned off.

Power Bank Function

The ETENWOLF ZEPHYR S3C can function as a power bank to charge your electronic devices such as phones, tablets, laptops, drones, and cameras. It has a USB-A Output 5V 2A, 10W.

Diagram showing the ETENWOLF ZEPHYR S3C charging a smartphone
Image: The air compressor connected via USB-A to charge a smartphone, demonstrating its power bank capability.

Notes on Power Bank Use:

  • To work as a power bank, the inflator needs to be powered on.
  • After 3 minutes of charging, the display panel will only indicate the battery level to save battery.
  • After 2 minutes of fully charging the devices, the inflator will automatically turn off.

Maintenance

Battery Charging & Indicator

For optimal performance, fully charge the inflator before using it for the first time. Connect it to a certified 5V 3A / 5V 2A charger with the provided charging cable.

Diagram showing the ETENWOLF ZEPHYR S3C connected to a charger
Image: The air compressor connected to an AC power supply for charging.

Charging with AC power supply:

  • For best charging performance, use a 5V 3A 15W PD charger. Full charge (0% to 100%) takes approximately 3.5 hours.
  • Using a 5V 2A 10W charger, full charge takes approximately 6 hours.

Battery Indicator: The battery level indicator (22) is shown by four bars, with each bar representing 25% of capacity.

Notes on Charging:

  • After 2 minutes of inactivity after being fully charged, the inflator will automatically shut off.
  • The inflator cannot be used while it is charging.

Pressure Recalibration

Different altitudes can cause variations in pressure by 1-3 PSI. In high altitude areas (especially over 5000 ft/1524 meters), users can recalibrate the pump's pressure sensor.

Recalibration steps:

  1. Power on the pump (05).
  2. Hold the Light button (02) and Mode button (04) for 10 seconds.
  3. When the entire screen flickers, recalibration is complete.

Notes on Recalibration:

  • Power off the pump before calibration.
  • The Pressure hose (09) should not be connected to any item. Any item which gives pressure to the hose will disable the process of recalibration.
  • A charged battery or other power source is required to process recalibration.
  • There is no memory for the new recalibration settings. Once the power is turned off, it will be reset to sea level calibration (altitude 0 ft/meters).

Troubleshooting

Refer to the table below for common issues and their solutions:

ProblemSolution
Slow inflation speed
  • Check whether the battery is sufficient.
  • Check whether the item inflated is leaking.
  • Check whether the air nozzle connection is tightened.
  • Check whether the inflation hoses are broken.
  • Check whether the ventilation slots are blocked.
Air compressor turns on, but does not inflate
  • Check whether the battery is sufficient.
  • Check whether the pressure of the item being inflated exceeds the preset pressure.
Unable to increase or decrease the preset pressure
  • Make sure the correct mode is chosen, and the preset value does not exceed the range.
  • Select the manual mode and adjust the preset value within the pressure range of 3-160 PSI.
The inflator inflates but the pressure shown on the display is zero.If the air pressure is under 3 PSI, the pressure displayed will show zero due to the pump's minimum pressure range.
The battery level indicator is different when inflating compared to the standby state.The lithium battery's voltage level significantly drops when discharging power, causing the battery level indicator to have a different display when inflating compared to a standby state. It is a normal situation.
The battery level indicator does not show on the screen after charging.Use a certified ETENWOLF charger or standard charger, and the included charging cable, and try to charge it.
There is an air leakage when connecting the high-pressure air hose.Tighten the air nozzle.
Safety alert symbol light on display shows the E08 error code.After shutting down and restarting, if the issue persists, send the device for factory repair.
Display shows the E10 error code.This is a motor malfunction warning. If the issue persists after shutting down and restarting, send the device for factory repair.
Display shows the E11 error code.Low-temperature charging protection. Restore temperature to above 0 degrees Celsius before continuing charging.
Display shows the E12 error code.High-temperature charging protection. Restore temperature to below 45 degrees Celsius before continuing charging.
Display shows the E13 error code.Low-temperature discharge protection. Restore temperature to above -20 degrees Celsius before continuing.
Display shows the E14 error code.High-temperature discharge protection. Restore temperature to below 58 degrees Celsius before continuing.
Display shows the E15 error code.Air pump exceeded working time. Check if the inflated item has any leakage.
Display shows the E16 error code.Overpressure protection. It will return to normal after pressure release.
Display shows the E17 error code.High-pressure operation exceeded working time. Check if the inflated item is functioning abnormally.
Display shows the E18 error code.Battery damage warning. After 30 seconds flashing, the device will shut down. Send for factory repair.

Specifications

NameAir Inflator
ModelZephyr S3/S3 Plus Air Compressor
Dimensions134 x 171 x 96mm
Inflation pressure range3-160 PSI / 0.2-11 Bar
Operating TemperatureCharging: 0°C-45°C / 30°F-113°F
Discharging: -20°C-70°C / -4°F-158°F
Storage temperature-10°C-60°C / -14°F-140°F
High pressure air tube length0.9 meters
Battery capacity7800mAh for S3 / 9600mAh for S3 Plus
Working noiseLower than 85dB within 1 meter
InputType-C: 5V 3A
OutputUSB-A: 5V 2A
Charging time15W: 3.5 hours / 10W: 6 hours
Continuous working timeApproximately 25 minutes at a pressure range of 20-50 PSI, in a 25°C ambient temperature, under full charge.
Sensor accuracy±1 PSI

Unit conversion: 1 Bar = 14.5 PSI. 1 Bar = 100 KPa.

Safety Instructions

  • This product is not a toy and should not be used by children. Users should be above 16 years old. Keep a safe distance between children and the inflator while inflating.
  • There is a built-in lithium battery inside the product. Don't place the product into fire or dispose of the battery improperly.
  • Overheating damage or water ingress may increase the risk of fire or explosion. It's best to keep the product away from heat sources, and not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a chance it could explode.
  • Please store the product within temperatures ranging from -10°C-60°C (-14°F-140°F). Extremely hot or cold environments may damage the battery and shorten the lifetime of the inflator. Long-time storage of the product may decrease the effectiveness of the battery.
  • Charge the inflator at least once every three months to maintain its performance.
  • The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
  • If there is an unusual noise or the temperature becomes very high during inflating, please turn off the inflator immediately.
  • Before setting the inflation pressure value, make sure the pressure unit is correctly selected. Mixing up PSI and Bar could lead to dangerous overinflation.
  • Do not leave the pump unattended while it is in operation.
  • Please use the product in a dry and clean environment. The intrusion of sand and dust may cause damage to the product. Don't wash the product with water.
  • Make sure to use ETENWOLF's charger or other certified PD chargers, and the included charging cable to charge this product. Malfunction caused by actions not in accordance with the above requirements is not covered by the warranty.
  • To reduce the risk of electric shock, do not expose to rain. Store indoors.
Diagram illustrating 8 integrated safety protection features
Image: Visual representation of the ultimate safety protection features, including AI-software, high/low-temperature, over-charge, over-current, over-voltage, short-circuit, and over-load protection.

User Tips

  • Many users find this inflator to be quiet and fast, especially when adjusting pressure for cars, motorcycles, and bicycles.
  • The device is noted for its precision in pressure readings.
  • It generally does not get warm even after inflating multiple tires, and the battery capacity is sufficient for several uses.
  • Remember that various nozzles and adapters are conveniently stored behind the inflator for easy access.
  • The motor intelligently slows down as it approaches the target pressure, ensuring accurate inflation.
  • The built-in power bank function is a useful feature for charging smartphones and other small electronic devices on the go.

Frequently Asked Questions (FAQ)

Q: How do I turn the ETENWOLF ZEPHYR S3C on and off?
A: Long-press the Start/pause power button (05) for two seconds to turn it on. To turn it off, long-press the same button for two seconds while the inflator is on.
Q: How do I switch between inflation modes?
A: Press the Mode button (04) to cycle through the available modes: Manual, Car, Bicycle, and Ball mode.
Q: Can I use this device to charge my phone?
A: Yes, the ETENWOLF ZEPHYR S3C has a power bank function with a USB-A output (5V 2A, 10W). Ensure the inflator is powered on to use this feature.
Q: What should I do if the inflation speed is slow?
A: Check the battery level, ensure the item being inflated is not leaking, tighten the air nozzle connection, inspect inflation hoses for damage, and ensure ventilation slots are not blocked. Refer to the Troubleshooting section for more details.
Q: How long does the battery last on a full charge?
A: The 7800mAh battery provides approximately 25 minutes of continuous working time when inflating within a 20-50 PSI range at 25°C ambient temperature. Standby time is up to 365 days.

Warranty & Support

2-Year Coverage: Within two years of purchase, ETENWOLF provides timely and effective online after-sale service. They will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Information:

A PDF version of this user manual is available at: User Manual (PDF)

Made in P.R.C.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.