1. Introduction
Thank you for purchasing the Baofeng BF-K5 Plus Walkie Talkie. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. To ensure maximum performance and safe operation, please read this manual carefully before use.
1.1 Regulations and Safety Warnings
EU Regulatory Conformance: This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2006/66/EC, 2011/65/EU, and 2012/19/EU. This information applies to EU countries only.
FCC Part 15/IC Compliance: This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the responsible party could void your authority to operate the equipment.
FCC RF Exposure: It is the user's responsibility to operate this radio transmitter safely. Adhere to the following:
- Do not use the radio with a damaged antenna. Contact your local dealer for a replacement.
- For hand-held operation, hold the radio 1 inch (2.5 cm) from your face to comply with FCC RF exposure requirements.
- For body-worn operation, use only supplied or designated accessories to meet Industry Canada RF exposure guidelines. Avoid third-party accessories unless approved by the manufacturer.
Precautions for Portable Terminals:
- Do not operate the product in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate where wireless communication equipment is prohibited.
1.2 Important Tips
To make better use of your radio:
- Do not use unauthorized or damaged accessories.
- Keep the product at least 2.5 cm away from your body during transmission.
- Avoid prolonged reception at high volume.
- In vehicles with airbags, do not place the product in the airbag deployment area.
- Keep the product and accessories out of reach of children and pets.
- Operate the product within the specified temperature range.
- Continuous transmission can cause heat accumulation; allow for proper cooling.
- Handle the product with care.
- Do not disassemble, modify, or repair the product or its accessories without authorization.
1.3 Content of the Packaging
The standard package includes:
- 1 x Radio Unit (BF-K5 Plus)
- 1 x Antenna
- 1 x Li-Ion Battery Pack
- 1 x Belt Clip
- 1 x Hand Strap
- 1 x Type-C Cable
- 1 x Product Manual
- 1 x Box
Please note that the specific contents may vary slightly depending on whether you selected the NO GPS or GPS version. Please verify your selection when ordering.

2. Setup
2.1 Charging the Battery
The Li-ion battery pack is not charged at the factory; charge it before first use. For optimal performance, fully charge and discharge the battery two or three times. The battery pack life may deplete over time; replace if operating time decreases despite proper charging.
Precautions for Batteries:
- Do not charge or replace your battery in locations with fuels, chemicals, or explosive materials.
- Dry a wet battery with a soft, clean cloth before charging.
- Do not charge deformed, leaking, or overheated batteries.
- Use only the specified charger provided by the company.
- Do not charge in areas with strong radiation.
- Avoid overcharging, as it shortens battery life.
2.1.1 How to Charge (Using the Supplied Charger)
- Plug the AC adapter into an AC outlet, then connect its cable to the DC jack on the charger's back. The indicator light blinks orange, ready for charging.
- Plug the battery or the radio into the charger, ensuring good contact with charging terminals. The indicator turns red, indicating charging.
- Full charge takes approximately 2-5 hours. The indicator turns green when charging is complete.
- Remove the battery or radio unit from the charger.
Note: If the radio is powered on during charging, the indicator may not turn green to show full charge. For accurate indication, turn off the radio while charging.
2.1.2 Using the Type-C USB Charger
The Type-C USB port allows convenient charging of your Li-ion battery pack.
- Ensure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet.
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will indicate charging progress.
Note: It is recommended to power off your radio while charging. If powered on and the battery is completely empty, you may not be able to transmit immediately. Allow the battery to charge to at least one bar before attempting to transmit. For optimal battery life, remove the radio from the charger within 6 hours; do not store the radio connected to the charger.

2.1.3 How to Store the Battery
- Store the battery at approximately 80% discharge.
- Keep it in a low-temperature, dry environment, away from heat and direct sunlight.
- Do not short-circuit battery terminals or attempt to remove the casing.
- Never store the battery in unsafe surroundings; a short circuit can cause an explosion.
2.2 Installation of Accessories
2.2.1 Installing / Removing the Antenna
- Installing: Screw the antenna into the connector on top of the transceiver. Hold the antenna at its base and turn clockwise until secure.
- Removing: Turn the antenna counter-clockwise to remove it.
2.2.2 Installing the Belt Clip
- Locate the two parallel screws above the battery on the radio's back. Remove them, align the belt clip holes, and screw them back into the radio body.
- Removing: Unscrew counter-clockwise to remove the belt clip.
2.2.3 Installing the Battery Pack
Before attaching or removing the battery, ensure your radio is turned off by rotating the power/volume knob fully counter-clockwise.
- Align the battery parallel with the radio body, with its lower edge about 1-2 cm below the radio's edge.
- Slide the battery upward along the guide-rails until it clicks into place.
Removing the Battery Pack: Press the battery release above the battery pack while sliding the battery downward.
2.2.4 Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack. The BF-K5 Plus uses a 2-pin Kenwood jack.
3. Radio Overview
3.1 Buttons and Controls of the Radio

- Power/Volume knob: Rotate to turn on/off the radio and adjust volume.
- SK1 - Broadcast FM and Alarm key: Momentary press for FM radio, press and hold for alarm.
- PTT key (Push-to-Talk): Press and hold to transmit.
- VFO/MR mode key: Switches between Frequency (VFO) and Memory (MR) modes.
- Status LED: Indicates radio status (red for transmitting, green for receiving).
- SK2 - Flashlight and Monitor key: Momentary press for flashlight, press and hold to monitor signal.
- A/B select key: Switches between upper (A) and lower (B) displays.
- MENU key: Enters the menu system.
- Numeric keypad: For inputting frequencies, channel numbers, and menu selections.
- Antenna jack: Connection point for the antenna.
- LED flashlight: Built-in light source.
- Color LCD: Displays radio information.
- Accessory jack: For external speaker/microphone.
- Speaker and microphone: For audio input and output.
- One-Touch search key: Activates one-touch frequency search.
- EXIT key: Exits menus and functions.
- Up/Down navigation keys: For navigating menus and adjusting frequencies/channels.
- Type-C charging port: For charging the battery.
- Type-C charging indicator: Indicates charging status.
- Battery release latch: Releases the battery pack.
3.2 LCD Display Icons
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| DTMF side tone indicator | |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Repeater access: TX shifted higher than RX |
| - | Repeater access: TX shifted lower than RX |
| D | Dual watch enabled |
| Keypad lock enabled | |
| VOX enabled | |
| Confidential calling feature activated | |
| N | Narrowband enabled |
| Battery level indicator | |
| R | Reverse function enabled |
| Indicates active band or channel | |
| SCR | Voice scramble function activated |
Battery Level Indicator: When the battery level indicator shows an empty battery, the radio will beep, flash the backlight, and announce 'Low Voltage' (if voice prompts are enabled), indicating it needs charging.
4. Basic Operations
4.1 Power On/Off
- Turning On: Rotate the Power/Volume knob clockwise until you hear a 'click'. The display will show a message or flash the LCD, then display a frequency or channel. If voice prompt is enabled, it will announce 'frequency mode' or 'channel mode'.
- Turning Off: Rotate the Power/Volume knob counter-clockwise until you hear a 'click'. The unit is now off.
4.2 Adjusting the Volume
Rotate the Power/Volume knob clockwise to increase volume, and counter-clockwise to decrease. Be careful not to turn it too far, as it may turn off the radio. Use the monitor function (press and hold [SK2]) to adjust volume to the un-squelched static.
4.3 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between the upper (A) and lower (B) displays. The selected display's frequency or channel becomes the active listening and transmit frequency. To save frequencies to channel memory, you must be on the A display.
4.4 VFO/Channel Switch
Press the [VFO/MR] key to switch between VFO (Frequency) and Channel (MR) display modes.
- In Channel (MR) mode, the channel number is displayed.
- In Frequency (VFO) mode, 'VFO' is displayed.
4.5 Making a Call
Note: Press the [A/B] key to switch the main channel if two channels are displayed. In standby mode, press [VFO/MR] to switch between VFO and MR modes.
- Channel Mode Call: Select a channel, then hold [PTT] to transmit. Speak into the microphone. The red LED will be on.
- Frequency Mode Call: Switch to VFO mode, input the desired frequency, then hold [PTT] to transmit. Speak into the microphone. The red LED will be on.
- Receiving a Call: Release the [PTT] key to answer. The green LED will be on when receiving.
Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.
4.6 Using the Flashlight
The radio has a high-intensity LED flashlight for emergencies.
- Press [SK2] key once to turn on the flashlight continuously.
- Press [SK2] key again to activate the strobe emergency mode (flashing light).
- Press [SK2] key a third time to turn off the flashlight.
4.7 Emergency Alert
To signal for help, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] again to exit. WARNING: Use this feature only in actual emergencies.
4.8 FM Radio (FM)
The radio can receive FM broadcasts in the 65-108 MHz range. The key switches between 65-75 MHz and 76-108 MHz bands.
- In frequency or channel mode, press [SK1] to turn on the FM radio.
- Select the desired frequency using the Up/Down keys or input directly. Press #z to automatically search for stations.
- Press [SK1] to exit FM radio.
Note: If a signal is received on the A/B display while listening to FM, the radio will automatically switch to that frequency for normal transmitting/receiving. It will return to FM radio mode when the signal disappears.
4.9 Monitor
In standby, press and hold the [SK2] key to enter Monitor mode. This allows you to hear weak signals or matched carriers even if signaling is present. Release [SK2] to exit. If no signal is present, it will emit noise.
4.10 Keypad Lock
The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the * key for about two seconds. You can also configure the radio to automatically lock the keypad after ten seconds via the menu.
4.11 Frequency Reversal
A momentary press of the * key enables the reverse function. If you want to listen to the repeater's input frequency, press * momentarily to reverse your transmit and receive frequencies. 'R' will appear on the screen.
4.12 TX Repeater Tone
Press [PTT] + [SK2] key to send a 1750Hz repeater tone. This is useful for communicating through repeaters. This function works even if the keypad lock is enabled.
4.13 One-Touch Frequency Search
- Press and hold the key. The screen will display 'SEARCH SEARCH...'.
- When a strong, stable signal is received, the frequency will be displayed. If CTCSS/DCS is present, it will also be shown.
- Press the key to save the searched frequency and CTCSS/DCS to a channel.
Note: During search, press #z to switch between UHF or VHF bands.
4.14 Weather Radio/Scan Weather Channel (NOAA)
The radio has a NOAA Weather Radio function to receive weather reports and scan 10 NOAA weather channels.
- To turn on NOAA Weather Scan, press and hold the [0sQL] key for 3 seconds. An icon will appear, and the radio will enter Weather band mode.
- Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Pressing and holding #z again will stop the scan.
- After stopping the scan, you can manually select weather channels using the Up/Down keys.
- To exit Weather Radio broadcast mode, press the key or [PTT] key.
Note: Weather Channels Wx 1-10 are receive-only for NOAA and Canadian weather broadcasts; you cannot transmit on these channels.
5. Advanced Features
5.1 Working the MENU System
The radio's menu system allows customization of various settings. For a complete reference, refer to Appendix C. - Shortcut Menu operations. Note that if your radio is in Memory (MR) mode, certain menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.
5.1.1 Basic Use of the Menu with Arrow Keys
- Press the MENU key to enter the menu.
- Use the Up/Down keys to navigate between menu items.
- Once you find the desired item, press MENU again to select it.
- Use the Up/Down keys to select the desired parameter.
- To confirm your selection, press MENU to save and return to the main menu. To cancel changes, press EXIT to reset and exit the menu.
- To exit the menu at any time, press EXIT.
5.1.2 Using Menu Shortcuts
Each menu item has a numerical value for direct access. The ten most common functions are at the top.
- Press the MENU key to enter the menu.
- Use the numeric keypad to enter the number of the menu item.
- To enter the menu item, press MENU.
- For parameters, use arrow keys or the numeric keypad for the shortcut code.
- To confirm, press MENU to save. To cancel, press EXIT to reset and exit.
- To exit the menu at any time, press EXIT.
5.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your programmed channels. To enable the scanner, press and hold the #z key for about two seconds. Press and hold #z again to exit scanning mode.
5.2.1 Scanning Modes
The scanner can operate in three modes: Time, Carrier, or Search.
- Press MENU to enter the menu.
- Enter '21' for scanner mode.
- Press MENU to select.
- Use Up/Down keys to select the scanning mode.
- Press MENU to confirm and save.
- Press EXIT to exit the menu.
- Time Operation (TO): Scanner stops on a signal, then resumes scanning after a preset time.
- Carrier Operation (CO): Scanner stops on a signal, then resumes scanning after a preset time with no signal.
- Search Operation (SE): Scanner stops on a signal. You must press and hold #z again to resume scanning.
5.2.2 Frequency Scanning
- In frequency mode, press and hold #z for more than 2 seconds. The radio will scan frequencies according to the set frequency step.
- Change scanning direction with Up/Down keys.
- Press #z to stop scanning.
5.2.3 Channel Scanning
- In channel mode, press and hold #z for more than 2 seconds. The radio will scan channels according to your settings.
- Change scanning direction with Up/Down keys.
- Press #z to stop scanning.
5.2.4 Scan CTCSS
This function scans frequencies with CTCSS tones enabled.
- In standby mode, press MENU, then '14'. 'Scan CTCSS' will appear.
- Press MENU, and CTCSS tone scanning will start.
Note: This function cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.
5.2.5 Scan DCS
This function scans frequencies with DCS codes enabled.
- In standby mode, press MENU, then '15'. 'Scan DCS' will appear.
- Press MENU, and DCS code scanning will start.
Note: This function cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.
5.3 Manual Programming (Channels Memory)
Memory channels store commonly used frequencies, transmit power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier. The radio features up to 999 memory channels (640 for GPS version).
Frequency Mode vs. Channel Mode: In standby mode, press [VFO/MR] key to switch between Frequency (VFO) mode and Channel (MR) mode.
5.3.1 Programming a Channel Repeater Offset with CTCSS Tone (Example for Channel 10)
RX = 432.55000 MHz, TX = 437.55000 MHz (a +5 Offset), TX CTCSS tone 123.0
- Press MENU to switch between menus.
- Press [VFO/MR] to set the radio to VFO mode (VFO icon displayed).
- MENU, '31', '10' (Deletes prior data in channel 10).
- MENU, '12', '123.0' (Selects desired TX encode tone).
- Enter RX frequency (e.g., 43255000).
- MENU, '30', '10' (Enters desired channel 10, RX has been added).
- Enter TX frequency (e.g., 43755000).
- MENU, '30', '10' (Enters same channel 10, TX has been added).
- Press [VFO/MR] to return to MR mode.
5.3.2 Programming a Simplex Channel with CTCSS Tone (Example for Channel 10)
RX = 432.6625 MHz, TX CTCSS tone 123.0
- Press MENU to switch between menus.
- Press [VFO/MR] to set the radio to VFO mode (VFO icon displayed).
- MENU, '31', '10' (Deletes prior data in channel 10).
- MENU, '12', '123.0' (Select desired TX encode tone).
- Enter RX frequency (e.g., 43266250).
- MENU, '30', '10' (Enters desired channel 10, RX has been added).
- Press [VFO/MR] to return to MR mode.
5.4 Repeaters Programming
These instructions assume you know your repeater's transmit/receive frequencies and are authorized to use them.
- Press [VFO/MR] to set the radio to VFO mode (VFO icon displayed).
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press MENU to enter the menu.
- Enter '29' for frequency offset.
- Press MENU to select.
- Use the numeric keypad to enter the specified frequency offset.
- Press MENU to confirm and save.
- Enter '28' for offset direction.
- Use Up/Down keys to select + (positive) or - (negative) offset.
- Press MENU to confirm and save.
- Optional: Save to memory (see Manual Programming) or set up CTCSS (see CTCSS section).
- Press EXIT to exit the menu.
Note: If you experience problems connecting to the repeater, check your settings or contact your dealer for technical support. Some amateur radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater.
5.5 VOX (Voice Activated Transmit)
VOX allows hands-free conversations. Speak into the microphone, and communication activates automatically.
- In standby mode, press MENU, then '17'. The screen will display 'VOX'.
- Press MENU to enter. Use Up/Down keys to select OFF/ON or VOX level (1-10).
- Press MENU to confirm.
- To return to standby, press EXIT.
Note: Level 1 is least sensitive, level 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.
5.6 Dual Watch
Dual Watch allows monitoring two channels simultaneously. The radio features single-receiver Dual Watch functionality, with the ability to lock the transmit frequency to one of the monitored channels.
5.6.1 Enabling or Disabling Dual Watch Mode
- Press MENU to enter the menu.
- Enter '7' on the numeric keypad for Dual Watch.
- Press MENU to select.
- Use Up/Down keys to enable or disable.
- Press MENU to confirm.
- Press EXIT to exit the menu.
5.7 Scrambler
The scrambler protects communications by voice inversion, preventing others from understanding your conversations. The 'SCR' icon appears when enabled.
- In standby mode, press MENU, then '45'. The screen displays 'SCRAMBLE'.
- Press MENU to enter. Use Up/Down keys to select scramble mode (MODE1 to MODE3) to activate.
Note: The M version supports voice scrambling functions. The L version does not support voice scrambling functions.
5.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals for any given code, commonly used in two-way radio systems for automation and remote control (e.g., activating repeaters).
The radio fully implements DTMF, including A, B, C, and D codes. Numeric keys, as well as *, and #z, correspond to DTMF codes. A, B, C, and D codes are located on the Up, Down, MENU, and EXIT keys respectively.
To send DTMF codes, press the key(s) corresponding to the message while holding down the PTT key. This works even with keypad lock enabled.
5.9 Customization
The radio allows customization of visual and audible features.
5.9.1 Display Backlight (ABR) - MENU 7
- In standby mode, press MENU, then '7'. The screen displays 'ABR'.
- Press MENU to enter. Use Up/Down keys to select backlight duration (ON/5sec/10sec/15sec/20sec).
- Press MENU to confirm.
- To return to standby, press EXIT.
5.9.2 Beep PROMPT (BEEP) - MENU 8
If enabled, a beep tone sounds every time a key is pressed.
- In standby mode, press MENU, then '8'. The screen displays 'BEEP PROMPT'.
- Press MENU to enter. Use Up/Down keys to turn ON/OFF the beep function.
5.9.3 Voice Function (VOICE) - MENU 17
Enables/disables voice confirmation of key presses.
- In standby mode, press MENU, then '17'. The screen displays 'VOICE'.
- Press MENU to enter. Use Up/Down keys to select OFF/ON.
- Press MENU to confirm.
- To return to standby, press EXIT.
5.9.4 Language of the MENU (LANGUAGE) - MENU 18
Sets the menu language (English or Chinese).
- In standby mode, press MENU, then '18'. The display will show 'LANGUAGE'.
5.9.5 Working Mode (MDF-A) - MENU 24
The radio has four working modes: Frequency (FREQ), Channel (CH), Channel Name (NAME).
- In standby mode, press MENU, then '24'. Select the desired working mode with Up/Down keys.
- Press MENU to confirm.
5.9.6 Roger Beep, End Transmission Tone (ROGER) - MENU 36
Enables/disables a tone at the end of transmission.
- In standby mode, press MENU, then '36'. The screen displays 'ROGER'.
- Press MENU to enter. Use Up/Down keys to select OFF/ON.
- Press MENU to confirm.
- To return to standby, press EXIT.
5.9.7 Power On Message (POWER ON MSG) - MENU 40
Customizes the welcome message displayed on startup.
- In standby mode, press MENU, then '40'. The display will show 'POWER ON MSG'.
- Press MENU to enter. Use Up/Down keys to select options (VOLTAGE, MESSAGE, LOGO, MODEL NAME).
- Press MENU to confirm.
- To return to standby, press EXIT.
5.9.8 Power On Password (POWER ON PWD) - MENU 43
Enables a password requirement on startup.
- In standby mode, press MENU, then '43'. The display will show 'POWER ON PWD'.
- Press MENU to enter. Use Up/Down keys to enable/disable (ON/OFF).
- Press MENU to confirm.
- To return to standby, press EXIT.
If enabled, 'Input Password' will be displayed on startup.
5.10 Reset - MENU 42
The transceiver has two reset modes: VFO (resets all settings except channels) and ALL (resets all settings).
5.10.1 Reset VFO
- In standby mode, press MENU, then '42'. The screen displays 'RESET'.
- Press MENU to enter. Use Up/Down keys to select VFO.
- Press MENU to confirm. 'Sure to reset?' will display.
- Press MENU again to confirm. 'Wait...' will display, then the transceiver will turn off and reboot.
5.10.2 Reset ALL
- In standby mode, press MENU, then '42'. The screen displays 'RESET'.
- Press MENU to enter. Use Up/Down keys to select ALL.
- Press MENU to confirm. 'Sure to reset?' will display.
- Press MENU again to confirm. 'Wait...' will display, then the transceiver will turn off and reboot.
6. User Tips
- Bluetooth Functionality: Note that neither the GPS nor the non-GPS versions of the BF-K5 Plus Walkie Talkie include Bluetooth functionality.
- Programming Software: For advanced programming and channel management, consider using a programming cable and compatible software. This allows for easier setup of authorized frequencies, bandwidth, and power levels.
- Battery Maintenance: To prolong battery life, avoid fully discharging the battery frequently. Charge it when the low battery indicator appears, and remove it from the charger once fully charged.
7. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio. | Battery installed improperly, battery power low, dirty/damaged battery contacts. | Remove/reattach battery, recharge/replace battery, clean battery contacts. |
| Weak or intermittent voice during reception. | Battery voltage low, volume level low, loose/incorrect antenna, blocked speaker. | Recharge/replace battery, increase volume, reattach antenna, clean speaker. |
| Cannot communicate with other group members. | Inconsistent frequency/signaling type, too far from others, interference from other radios. | Verify TX/RX frequency and signaling, move closer to others, change frequency/adjust squelch. |
| Hear unknown voices or noise. | Radio in analog mode with no signaling, too far from others, unfavorable position (blocked by buildings/underground), external disturbance. | Request dealer to set signaling, move closer to others, move to open area, restart radio, stay away from interference. |
| Radio keeps transmitting. | VOX enabled, headset not installed. | Turn off VOX, check headset. |
Note: If these solutions do not resolve your issues, please contact your dealer for technical support.
8. Technical Specifications

8.1 General
- Frequency Range:
- AM: 108-136MHz (RX)
- FM: 65-108MHz (RX)
- Police: 350-390MHz (RX)
- VHF: 136-174MHz (TX & RX)
- VHF: 200-260MHz (TX & RX)
- UHF: 400-480MHz (TX & RX)
- UHF: 480-520MHz (RX)
- Transmission Frequency: 144-148 & 420-450MHz (America version), 144-148 & 430-450MHz (Canadian version)
- Channel Spacing: 25.0 KHz (Wide) / 12.5 KHz (Narrow)
- Memory Channel: 999 Groups (NO GPS Version), 640 Channels (GPS Version)
- Operation Voltage: DC 7.4 V ±10%
- Operating Temperature: -10℃ to 60℃
- Antenna Impedance: 50Ω
- Radio Dimensions: 135mm X 63mm X 39mm (not including antenna)
- Radio Weight: 290g (with Li-ON battery)
- Waterproof / Water-Resistant: IP45
- Material: Plastic
- Certification: CE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee
8.2 Transmitter
- RF Output Power: 7 Watts Max (5W-10W)
- Modulation: 16KOF3E/11KOF3E
- Spurious Emission: -16 dBm <1GHz, -16 dBm >1GHz
- Frequency Stability: ±2.5 ppm
- Audio Distortion: ≤5%
- FM Hum & Noise: 40 dB
- Transmission Current: ≤2800mA
8.3 Receiver
- Sensitivity: 0.25μV (12dB SINAD)
- Adjacent Channel Selectivity: -60 dBm
- Intermodulation and Rejection: -70 dBm
- Rated Audio Power Output: 0.75 Watts @ 16 Ω (1W @ 16 ohms)
- Rated Audio Distortion: ≤5%
- Receive Current: ≤380mA
Note: All specifications may be modified without prior notice or liability.
9. Warranty and Support
Your Baofeng BF-K5 Plus Walkie Talkie is an electronic product of exact design and should be treated with care. Unauthorized opening of the transceiver will void the warranty.
For tutorials, support, and more information, please visit the official website: www.baofengradio.com
A detailed user manual in PDF format is also available for download: Baofeng UV-5RM PLUS/K5PLUS User's Manual (PDF)
10. Regulatory Information
Disclaimer: The Company endeavors to ensure the accuracy and completeness of this manual. However, all specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed without prior written consent of the Company. We do not guarantee the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and contents involved in this manual.
This product is compliant with relevant FCC, CE, and RoHS standards.