Valkyrie Gla-360 Digital ARGB 3-Row CPU Liquid Cooler

1. Introduction

Thank you for choosing the Valkyrie Gla-360 Digital ARGB 3-Row CPU Liquid Cooler. This all-in-one (AIO) liquid cooling system is designed to provide superior thermal performance for your CPU, featuring a vibrant digital display on the pump head and customizable ARGB lighting. This manual will guide you through the installation, operation, and maintenance of your new cooler to ensure optimal performance and longevity.

Figure 1: Valkyrie Gla-360 Digital ARGB 3-Row CPU Liquid Cooler

2. Package Contents

Please inspect the package contents to ensure all components are present and undamaged:

• Valkyrie Gla-360 Radiator with integrated pump and cold plate
• 3 x 120mm ARGB Fans
• Intel Mounting Hardware (backplate, standoffs, brackets)
• AMD Mounting Hardware (standoffs, brackets)
• Fan Screws
• Radiator Screws
• Thermal Paste (pre-applied or in a tube)
• PWM Fan Splitter Cable
• ARGB Splitter Cable
• USB Cable (for pump display/software control)
• User Manual (this document)

3. Specifications

Below are the technical specifications for the Valkyrie Gla-360 Digital ARGB CPU Liquid Cooler:

Figure 2: Digital display on pump head

4. Installation Guide

Before you begin, ensure your system is powered off and unplugged. Refer to your motherboard and PC case manuals for specific instructions on component installation and clearances.

4.1. Prepare the Radiator and Fans

1. Attach the three 120mm ARGB fans to the radiator using the provided fan screws. Ensure the fan airflow direction is appropriate for your case's cooling configuration (typically blowing air through the radiator and out of the case, or into the case).
2. Mount the assembled radiator and fans to an available 360mm mounting location in your PC case (e.g., top, front, or side panel) using the longer radiator screws.

4.2. CPU Block Installation

The installation process varies slightly between Intel and AMD platforms. Follow the instructions relevant to your CPU socket type.

4.2.1. Intel Installation (LGA1700/1200/115X/2011/2066)

1. For LGA1700/1200/115X sockets, install the appropriate Intel backplate behind your motherboard. For LGA2011/2066, use the existing motherboard backplate.
2. Screw the correct Intel standoffs into the backplate (or directly into the LGA2011/2066 socket holes).
3. Attach the Intel mounting brackets to the pump head.
4. Carefully place the pump head onto the CPU, aligning the mounting holes with the standoffs. Ensure the pre-applied thermal paste (if present) makes good contact, or apply your own thermal paste if needed.
5. Secure the pump head by tightening the thumb screws onto the standoffs in a diagonal pattern until snug.

4.2.2. AMD Installation (AM5/AM4/AM3+/AM3/AM2+/AM2/FM2+/FM2/FM1)

1. Remove the stock plastic retention brackets from your motherboard, but retain the original AMD backplate.
2. Screw the correct AMD standoffs into the motherboard's backplate.
3. Attach the AMD mounting brackets to the pump head.
4. Carefully place the pump head onto the CPU, aligning the mounting holes with the standoffs. Ensure the pre-applied thermal paste (if present) makes good contact, or apply your own thermal paste if needed.
5. Secure the pump head by tightening the thumb screws onto the standoffs in a diagonal pattern until snug.

Figure 3: Copper cold plate for efficient heat transfer

4.3. Cable Connections

Proper cable management is essential for both aesthetics and airflow. Refer to your motherboard manual for header locations.

1. Fan Power: Connect the 4-pin PWM cables from the three fans to the included PWM splitter cable. Connect the splitter cable to your motherboard's CPU_FAN header.
2. ARGB Lighting: Connect the 3-pin ARGB cables from the three fans to the included ARGB splitter cable. Connect the splitter cable to a 5V 3-pin ARGB header on your motherboard.
3. Pump Power: Connect the 4-pin PWM cable from the pump to your motherboard's AIO_PUMP or CPU_OPT header. If neither is available, use a SYS_FAN header and ensure it is set to run at full speed in your motherboard's BIOS.
4. Pump Digital Display/Software: Connect the USB cable from the pump head to an available USB 2.0 header on your motherboard. This enables the digital display functionality and software control.

Figure 4: Comprehensive product overview with installation and wiring diagrams

5. Operating Instructions

5.1. Initial Power On

After completing the installation and double-checking all connections, power on your system. The fans and pump should start, and the digital display on the pump head should illuminate.

5.2. Digital Display Functionality

The pump head features a digital display that can show real-time information such as:

• CPU Temperature (°C/°F)
• GPU Temperature (°C/°F)
• CPU Load Percentage
• Fan Speed (RPM)
• Pump Speed (RPM)

The display content can typically be customized and monitored through the dedicated Valkyrie software (if available) or compatible motherboard software.

5.3. ARGB Lighting Control

The Addressable RGB (ARGB) lighting on the fans and pump can be controlled via your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync) or a dedicated ARGB controller (not included unless specified). Ensure your motherboard's ARGB header is enabled in the BIOS/UEFI settings.

5.4. Software Monitoring and Control

For advanced monitoring and control of pump speed, fan curves, and display customization, download the official Valkyrie software from the manufacturer's website. This software typically requires the USB connection from the pump to the motherboard's USB 2.0 header to function correctly.

6. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your liquid cooler.

• Dust Cleaning: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can impede airflow and reduce cooling efficiency. Use compressed air or a soft brush.
• Check Tubing: Occasionally inspect the tubing for any signs of kinks, damage, or leaks. While AIO coolers are sealed systems, it's good practice to check.
• Software Updates: Keep the Valkyrie control software and your motherboard's BIOS/UEFI updated to ensure compatibility and access to the latest features and performance optimizations.

7. Troubleshooting

If you encounter issues with your Valkyrie Gla-360 cooler, try the following steps:

8. User Tips

Based on general user experiences with similar products:

• Optimal Radiator Placement: For best performance, mount the radiator in a position where it can exhaust hot air directly out of the case, or intake cool air if your case airflow supports it.
• Cable Management: Take time to route cables neatly. This improves aesthetics and ensures unobstructed airflow within your PC case.
• BIOS Settings: After installation, enter your motherboard's BIOS/UEFI to ensure the CPU_FAN header (or equivalent) is set to PWM mode and the pump header is set to run at full speed for consistent cooling.
• Software Customization: Explore the Valkyrie software or your motherboard's RGB software to personalize the digital display and ARGB lighting effects to match your build.

9. Warranty and Support

The Valkyrie Gla-360 Digital ARGB 3-Row CPU Liquid Cooler comes with a manufacturer's warranty. Please refer to the warranty card included in your package or visit the official Valkyrie website for detailed warranty terms and conditions.

For technical support, troubleshooting assistance, or warranty claims, please contact Valkyrie customer service through their official website or the contact information provided with your product. When contacting support, please have your product model number (Gla-360 Digital Argb) and proof of purchase ready.