HITBOX AIT250P

Contents

HITBOX AIXZ AIT250P AC/DC Multi-Function Welding Machine User Manual

Model: AIT250P

Brand: HITBOX

1. Introduction

Thank you for choosing the HITBOX AIXZ AIT250P AC/DC Multi-Function Welding Machine. This versatile inverter welder is designed for a variety of welding tasks, offering MIG, TIG, and MMA (Stick) welding capabilities, including AC/DC TIG for precise aluminum welding. Equipped with advanced IGBT technology, Hot Start, Arc Force, and Anti-Stick functions, it provides reliable performance for both professional and hobbyist welders. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.

HITBOX AIXZ AIT200P AC DC Intelligent IGBT Inverter Welding Machine

Figure 1: HITBOX AIXZ AIT200P AC DC Welding Machine (Note: Model shown in image is AIT200P, features are similar to AIT250P)

2. Safety Information

Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death.

  • Electric Shock: Welding current can kill. Do not touch live electrical parts. Wear dry welding gloves and protective clothing. Ensure the machine is properly grounded.
  • Fumes and Gases: Welding fumes and gases can be hazardous to your health. Work in a well-ventilated area. Use an exhaust fan or fume extractor if necessary.
  • Arc Rays: Arc rays can burn eyes and skin. Wear a welding helmet with appropriate shade lenses and protective clothing.
  • Fire and Explosion: Welding sparks and hot metal can cause fires. Keep flammable materials away from the welding area. Have a fire extinguisher readily available.
  • Hot Parts: Welded parts and equipment can be hot. Allow them to cool before handling or wear appropriate heat-resistant gloves.
  • Noise: Excessive noise can damage hearing. Wear ear protection.

3. Product Overview

3.1 Key Features

  • Multi-Function 5-in-1: Supports TIG AC Square, TIG AC Pulse Square, TIG DC Pulse, TIG DC, and MMA welding modes.
  • IGBT Technology: Advanced Inverter Gate Bipolar Transistor technology for stable arc and efficient power usage.
  • Hot Start: Provides an initial boost of current to ensure easy arc ignition.
  • Arc Force: Automatically increases current to prevent the electrode from sticking during welding.
  • Anti-Stick: Reduces the welding current if the electrode sticks, making it easier to detach.
  • Welding Thickness: Capable of welding materials from 0.7mm to 6mm.
Diagram highlighting IGBT Technology, Hot Start, Arc Force, Anti-Stick, and welding thickness range of 0.7-6mm.

Figure 2: Key Features and Welding Thickness

Graphic illustrating the 5-in-1 multi-function welding modes: TIG AC Square, TIG AC Pulse Square, TIG DC Pulse, TIG DC, and MMA.

Figure 3: Multi-Function Welding Modes

3.2 Control Panel

The control panel allows for selection of welding modes and adjustment of parameters. Refer to Figure 4 for a visual guide.

  • TIG/MMA Selector: Provides selection between TIG and MMA (Stick) welding modes.
  • AC/DC Selector: For TIG welding, choose between AC (for aluminum) or DC (for steel, stainless steel, copper).
  • Mode Selector (MENU button): Enables selection of required mode parameters (e.g., Amperage, AC Balance, Pulse settings).
  • Amperage/Arc Force/Hot Start: Adjust these parameters using the rotary knob and corresponding buttons.
  • 2T/4T/Spot: Torch trigger modes for TIG welding.
Detailed diagram of the HBT250P AC/DC control panel, showing mode selectors, amperage/frequency/balance controls, and 2T/4T/Spot settings.

Figure 4: Control Panel Diagram

3.3 Included Accessories

The welding machine typically comes with the following accessories:

  • Hose Adjuster
  • Gas Nozzle
  • Collet Body
  • Collet
  • Gas Hose
  • Short Torch Tail
  • Long Torch Tail
  • Tungsten Bar
  • Electrode Holder (313cm/123.2in)
  • Earth Clamp (205cm/80.7in)
  • TIG Torch (400cm/157.4in)
  • 110V to 220V Adapter Cable
Image displaying various welding accessories including hose adjuster, gas nozzle, collet body, collet, gas hose, short torch tail, long torch tail, tungsten bar, electrode holder, earth clamp, TIG torch, and 110V to 220V adapter cable.

Figure 5: Included Welding Accessories

4. Specifications

Table 1: Technical Specifications
ParameterValue
Rated input voltage (V)220V
Frequency (HZ)50/60 HZ
Rated input power (KW)TIG: 4.37; MMA: 6.3
Rated input current (A)TIG: 28.1; MMA: 40.5
Rated input apparent power (KVA)TIG: 6.21; MMA: 8.9
Welding current adjust range (A)10 ~ 200
Welding voltage adjust range (V)10 ~ 26
No load voltage (V)50V (adjustable)
Material / Metal ProcessedStainless steel, Carbon steel
Rated Duty Cycle @40°C (MIG)60%
Weight (kg)20
CertificationCE
Table detailing technical specifications such as rated input voltage, frequency, input power, current, apparent power, welding current/voltage range, and no-load voltage.

Figure 6: Product Specifications Table

5. Setup and Connections

5.1 Power Connection

Ensure the welding machine is connected to a stable 220V power supply. Use the provided 110V to 220V adapter cable if necessary. The power switch is located on the rear panel (see Figure 7).

Rear view of the AIXZ Global AIT200P AC DC welding machine showing power input, fan, and gas connection.

Figure 7: Rear Panel with Power and Gas Connections

5.2 Welding Torch Installation

Proper connection of welding accessories is crucial for safe and effective operation. Refer to Figure 8 for visual guidance on various torch installations.

Diagrams for connecting welding torches for MIG/MAG, FLUX MIG, MMA, TIG, COLD, and CUT modes.

Figure 8: Welding Torch Installation Diagrams

5.2.1 MMA (Stick) Welding Setup

  • Connect the ground clamp to the negative (-) terminal.
  • Connect the electrode holder to the positive (+) terminal.
  • This setup is ideal for most 6010, 6011, 6013, and 7018 rods, with electrodes up to 5/32 inches.

Video 1: Product demonstration and setup, including MMA welding connections.

5.2.2 TIG Welding Setup

  • Connect the ground clamp to the positive (+) terminal.
  • Connect the TIG torch to the negative (-) terminal.
  • For gas TIG welding, connect the gas hose from your shielding gas cylinder to the gas inlet on the rear of the machine (Figure 7).
  • Tungsten electrodes with diameters of 1/8”, 3/32", 3/16", 1/16", and 5/32" can be used. It is recommended to use tungsten needles within a 3.2mm diameter for arc start.
  • When welding carbon steel in TIG mode, ensure the correct wiring method and appropriate welding wire are used.

6. Operation

6.1 Mode Selection

  1. Turn on the machine using the power switch on the rear panel.
  2. Use the TIG/MMA selector buttons on the control panel to choose your desired welding process.
  3. For TIG welding, select AC for aluminum or DC for other metals using the AC/DC selector buttons.
  4. Press the 'MENU' button to cycle through and select specific parameters for adjustment (e.g., Amperage, AC Balance, Pulse settings).

6.2 Parameter Adjustment

  • Amperage: Adjust the welding current using the main rotary knob. The display will show the current amperage.
  • Arc Force (MMA): Adjust the Arc Force to prevent electrode sticking and improve arc stability.
  • Hot Start (MMA): Adjust the Hot Start feature for easier arc ignition.
  • AC Balance (AC TIG): Controls the cleaning action and penetration when welding aluminum.
  • Pulse Settings (TIG Pulse): Adjust parameters like peak amps, base amps, pulse frequency, and pulse width for controlled heat input and reduced distortion.
  • 2T/4T/Spot (TIG): Select the torch trigger mode: 2T (two-touch) for simple on/off, 4T (four-touch) for continuous welding without holding the trigger, and Spot for tack welding.
Diagrams illustrating AC Square wave TIG Welding and AC Pulsed TIG Welding waveforms.

Figure 9: AC Square Wave and Pulsed TIG Welding Waveforms

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  • Cleaning: Regularly clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to blow out internal components periodically.
  • Cable Inspection: Inspect all welding cables, torch, and ground clamp for damage, fraying, or loose connections before each use. Replace damaged components immediately.
  • Gas System (TIG): Check gas hoses and connections for leaks. Ensure the gas cylinder is securely fastened and the regulator is functioning correctly.
  • Electrode Holder/TIG Torch: Clean the electrode holder jaws and TIG torch collet/collet body regularly. Replace worn-out consumables (nozzles, collets, tungsten).
  • Storage: Store the welding machine in a dry, clean environment, away from excessive dust, moisture, and extreme temperatures.

8. Troubleshooting

This section addresses common issues you might encounter during operation.

  • No Arc / Weak Arc:
    • Check power supply and connections.
    • Ensure ground clamp has good contact with the workpiece.
    • Verify correct welding mode and parameters are selected.
    • For MMA, check electrode type and condition. For TIG, check tungsten tip and gas flow.
  • Overheating:
    • Allow the machine to cool down. The thermal overload protection will reset automatically.
    • Ensure ventilation openings are not blocked.
    • Reduce duty cycle or welding current if continuously overheating.
  • Poor Weld Quality:
    • Adjust welding current, voltage, and travel speed.
    • Ensure proper shielding gas flow (for TIG/MIG).
    • Clean workpiece thoroughly before welding.
    • Check for correct electrode/filler wire size and type.
  • Gas Flow Issues (TIG/MIG):
    • Check gas cylinder pressure and ensure it's open.
    • Inspect gas hose for kinks or leaks.
    • Verify regulator settings.

9. User Tips

  • Practice Makes Perfect: Welding requires practice. Start with scrap materials to get a feel for the machine and different settings before working on important projects.
  • Cleanliness is Key: Always ensure your workpiece is clean and free of rust, paint, or oil. This significantly improves weld quality and reduces spatter.
  • Tungsten Preparation (TIG): Properly grind your tungsten electrode to a sharp point for DC TIG, or a balled end for AC TIG, to achieve a stable arc and good penetration.
  • Gas Flow Rate: For TIG welding, set your shielding gas flow rate correctly (typically 10-15 CFH for argon) to prevent atmospheric contamination of the weld.
  • Electrode Selection (MMA): Choose the correct electrode type and size for the material thickness and welding position.

10. Warranty and Support

10.1 Warranty Information

The HITBOX AIXZ AIT250P welding machine comes with a 1-year warranty from the date of discharge at the destination. This warranty covers manufacturing defects and ensures quality control from the beginning to the end of the production process.

10.2 Customer Support

For any questions, technical assistance, or warranty claims, please contact our customer service team. We are committed to providing high-quality products and excellent customer service.

Image with WhatsApp, Tel, and Email contact information for customer service.

Figure 10: Customer Service Contact Information

Contact Details:

  • WhatsApp: +86 16633953613
  • Tel: +86 166 3395 3613
  • Email: 1428040867@qq.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.