DOVAMAN GT10 APEX

Contents

DOVAMAN GT10 APEX 2800W Garden Shredder User Manual

Model: GT10 APEX

Introduction

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your DOVAMAN GT10 APEX 2800W Garden Shredder. Please read these instructions carefully before assembly, operation, or maintenance to ensure proper use and to prevent injury or damage.

The DOVAMAN GT10 APEX is designed for shredding garden waste, specifically dry branches up to 45mm in diameter. It features a powerful 2800W brushless motor, a 6-tooth roller blade, and a 60L collection box, all designed for quiet and efficient operation.

Safety Warnings

General Safety

  • Read this instruction manual thoroughly before use.
  • Do not allow children or inexperienced individuals to operate the machine.
  • Operate only if you are in good physical condition and fully alert.
  • Never use the machine under the influence of alcohol, drugs, or if feeling tired or ill.
  • Use the machine only for its intended purpose: shredding garden waste.
  • Do not alter the machine or its safety devices.
  • Keep children and bystanders away from the operating area.
  • Operate the machine in an open space on a firm, level surface, away from walls or other objects.
  • Do not operate in explosive atmospheres or on paved/gravel surfaces where ejected material could cause injury.
  • Do not expose the machine to rain or wet conditions.

Personal Protective Equipment (PPE)

  • Dress properly: wear tight-fitting clothing, avoid jewelry or loose clothing that could get entangled.
  • Wear protective hair covering for long hair.
  • Always wear ear protection to prevent hearing loss.
  • Wear protective glasses or goggles to protect eyes from debris.
  • Wear protective gloves to prevent injury to fingers.
  • Wear a face mask when shredding dry, dusty materials.
  • Wear sturdy shoes with a non-slip sole for good footing.

Electrical Safety

  • This is a Class I appliance; connect to a supply socket with an earth terminal.
  • Use only three-wire extension cords with three-prong grounding plugs and receptacles.
  • Avoid body contact with earthed or grounded surfaces during operation.
  • Use IEC60245 (HO7RN-F) outdoor extension cable with splash-proofed connector. Cross-section: at least 1.5 mm² for lengths up to 25m, and 2.5 mm² for lengths over 25m.
  • Ensure extension cables are fully unwound from reels and are not squeezed, bent, or wet.
  • Regularly check extension cables for damage to insulation. Replace damaged cables immediately.
  • Only plug into tested electrical circuits with matching voltage to the rating plate.
  • Never deactivate or bypass protective devices.
  • When using outdoors, always use a residual current-operated circuit-breaker (RCD) with an operating current of 30 mA or less.

Assembly

Before starting assembly, ensure the machine is switched off and unplugged. Wear protective gloves.

Component Identification

Refer to the diagrams below for component identification and assembly steps.

Diagram of shredder components with numbered parts
Figure 1: Main components of the shredder. Key parts include: 1. Feeding funnel, 2. Knob for setting blade, 3. Support, 4. Grass Box, 5. Support frame, 6. Wheel, 7. Interlock switch pusher, 8. Reset button / overload protector, 9. On/Off switch, 10. Rotational direction switch, 11. Power cable.

Assembly Steps

Follow the visual instructions provided in the diagrams for assembling the support frame, wheels, and collection box.

Assembly diagram page 1: Attaching the support frame and wheels
Figure 2: Assembly of the support frame and wheels. Pay attention to the direction of components as indicated.
Assembly diagram page 2: Securing the shredder unit to the base
Figure 3: Securing the shredder unit to the base. Ensure all parts are aligned in the same direction and secured with 4mm and 12mm fasteners as shown.
Assembly diagram page 3: Attaching the collection box
Figure 4: Final assembly step, showing the shredder with the collection box attached and ready for use.

Retaining Basket

The retaining basket (collection box) must be correctly attached and locked for the shredder to operate. The machine will not switch on if the lock lever is in the unlock position, and will automatically stop if the retaining basket is unlocked during operation.

  • Switch off and unplug the machine before attaching or removing the retaining basket.
  • Check the functionality of the interlock feature every two hours for safe operation.
  • Never attempt to override the interlock feature.
  • Lock lever: Upper position = Retaining basket is locked. Lower position = Retaining basket is unlocked.
Shredder with safety lock mechanism for the collection box
Figure 5: Safety lock mechanism for the collection box. The lock must be engaged for the shredder to operate.

Operating Instructions

Starting Up the Machine

Before connecting the plug or switching on the machine:

  • Check all screws, nuts, and other fasteners are properly secured.
  • Ensure guards, deflectors, and screens are in place and in good working condition.
  • Replace damaged or unreadable labels.
  • Make sure the filling hopper is empty.
  • Ensure the inlet and discharge opening are properly guarded.
  • Verify all parts of the machine are functioning correctly. Do not use if the switch does not work normally.

To start the shredder:

  1. Lift the 7-Interlock switch pusher up.
  2. Turn the 2-Knob for setting blade clockwise to the end, then counterclockwise for half a circle. This is the optimal initial setting.
  3. Press the 10-Rotational direction switch button down to the end, then press the On button. The machine will start shredding.

Feeding Material

Feed material into the filling hopper from the right side.

The shredder is designed to process:

  • All types of branches up to a maximum diameter of 45 mm (depending on wood type and condition).
  • Garden refuse such as withered plants or wet weeds (feed them alternating with branches).

The shredder is NOT designed to process:

  • Glass, metal, plastic, stones, ceramics, thicker branches, hard wood, thick wood plates, cloth, plastic bags, roots with soil.
  • Garbage in a liquid state, e.g., kitchen garbage.
Diagram showing recommended and not recommended materials for shredding
Figure 6: Recommended materials include dry branches, hardwood branches, and cut garden branches. Not recommended are vines, bamboo, fibrous plants, branches with many leaves, and wet branches.

For best results, shred branches, twigs, and wood just after they are cut, as they become very hard when dry. Remove any side shoots from branches if they are difficult to feed.

Do not let shredded material accumulate in the ejection opening; empty the retaining basket regularly.

Adjusting Blade Clearance

For effective operation, adjust the clearance between the counter blade and cutting roller.

  1. Switch on the device.
  2. Turn the fixing knob counterclockwise to release the adjusting knob.
  3. Turn the adjusting knob clockwise slowly to move the counter blade closer to the cutting roller.
  4. Continue until fine aluminum chips fall from the ejection opening.
  5. Turn the fixing knob clockwise to lock the adjusting knob.

Rotating the Knob for setting blade clockwise narrows the distance between the baffle and blades, resulting in finer cuts. This may increase the risk of overload protection. Rotating it counterclockwise widens the distance, leading to larger pieces. Adjust according to the size of the branches and desired output.

Forward / Reverse Switch

The shredder has a forward/reverse switch to help clear jammed material.

  • Position ↓ (Forward): Blades rotate in the forward direction for shredding.
  • Position ↑ (Reverse): Blades rotate in reverse to release jammed material.

To change to reverse direction, keep pushing the green button of the power switch to rotate the blades. The shredder automatically stops when you release the power switch. Several repetitions of reverse and forward operations may be required to shred a large object.

CAUTION: Switch off the shredder before changing the forward/reverse switch.

CAUTION: Always use a hook or a stick to remove jammed objects. Wait until the shredder stops completely before restarting.

Maintenance

CAUTION: Always ensure the machine is switched off and unplugged before performing any inspection or maintenance. Wear protective gloves. The cutter does not stop immediately after switch-off; wait until all parts stop completely.

General Maintenance

  • After each operation, check all locking screws and tighten if necessary.
  • Lubricate metal parts to protect against corrosion.
  • Keep the vents clean and free from dust.
  • Clean the machine using only a moist cloth and soft brush. Do not use gasoline, benzine, thinner, alcohol, or high-pressure water.
  • Store the machine in a dry room, out of reach of children. Never store outdoors.

Blade Cover Access

CAUTION: Make sure the machine is switched off and unplugged before opening the blade cover. Wear protective gloves.

If material clogs badly in the upper enclosure, remove it by opening the blade cover. The cutting roller and counter blade will wear out over time. Contact an authorized service center for replacement when necessary.

Servicing

Have your machine serviced by an authorized service center using only genuine replacement parts. Incorrect repair and poor maintenance can shorten the life of the machine and increase the risk of accidents.

Before servicing, inspection, adjustment, storage, or changing an accessory:

  • Shut off the power source.
  • Disconnect the machine from the power supply.
  • Make sure all moving parts have come to a complete stop.
  • Allow the machine to cool.

Inspect the machine for possible damage:

  • Check if safety devices work properly.
  • Ensure all moving parts work smoothly.
  • Verify all parts are undamaged and properly installed.
  • Replace or repair any damaged parts via an authorized service center.

Pay extreme attention when servicing the cutter. The cutter can move manually through the interlock feature of the guard functions.

Troubleshooting

WARNING: Before troubleshooting, switch off the machine, pull out the mains plug, and wait until the machine stops completely.

Trouble Possible Cause Remedy
Motor does not start Overload protection is activated Wait until the machine cools down and press the green button.
Safety cut-out device of the retaining basket (retaining basket is unlocked) Check and lock the retaining basket.
Motor sounds but does not start Cutting roller is blocked Turn off the device. Switch the forward/reverse switch into reverse direction. Switch on the machine until the jam has been cleared. Switch the machine off again. Turn back the direction of forward rotation.
Capacitor fault Bring machine to authorized service center for repairing.
Reverse rotation Switch off device and switch over direction of rotation selector switch.
Shredding material is not drawn into the shredder Shredding material caught in filling hopper Switch off device. Switch the forward/reverse switch into reverse direction. Switch on device to release the material, remove any foreign matter. Switch device off again. Turn back the direction of forward rotation.
Shredding material too soft or wet Push down with a branch.
Cutting roller worn Adjust fixed counter blade as described under "Adjusting the blade clearance". If the cutting roller is severely worn, replace it.
Shredding material is not cut cleanly Fixed counter blade is not adequately adjusted Adjust the counter blade.
Device starts but blocked by even slight load, and switches off by protective motor switch soon. Extension cable is too long or cross-section too thin. Socket is too far from mains supply or cross-section of mains cable too thin. Check the extension cable is at least 1.5 mm², maximum 25 m long. If using longer cable, minimum cross-section is 2.5 mm².

Specifications

Feature Detail
Brand Name DOVAMAN
Model GT10 APEX
Motor Type Brushless AC-Motor 230V~50Hz
Motor Rating P1 S6-40% 2800W
Motor Rating P1 S1 2000W
Torque Up to 400 Nm
Rotational Speed Cutting Roller 40 min⁻¹
Max. Branch Diameter (freshly cut wood) 40 mm (up to 45mm for dry branches)
Collection Box Capacity 60 Liters
Power Source Electric
Noise Level (Sound pressure level) 81.5 dB (A) (K=2.50 dB (A))
Noise Level (Sound pressure level at operator's ear) 88.84 dB (A) (K=1.40 dB (A))
Guaranteed Sound Power Level 90 dB (A)
Package Length 58 cm
Package Width 52 cm
Package Height 42 cm
Package Weight 33.0 kg
Diagram of the 2800W induction motor with planetary gear
Figure 7: Internal view of the 2800W induction motor with planetary gear, highlighting high efficiency, low energy loss, self-protection, and low noise level (88dB).

User Tips

  • For optimal performance and to prevent clogging, prioritize shredding dry branches. If you must shred wet garden waste, alternate it with dry wood.
  • Regularly check and adjust the blade clearance. A narrow gap is best for thin branches, while a wider gap suits thicker wood. Fine aluminum chips indicate correct adjustment for fine shredding.
  • Utilize the reverse function promptly if material jams. Always switch off and unplug the machine before attempting to clear any blockages manually with a hook or stick.
  • Keep the 60L collection box from overfilling to maintain a clean working area and prevent material from backing up into the shredder.
  • The brushless motor is designed for quiet operation (around 88 dB), making it suitable for residential use without causing excessive noise disturbance.

Warranty and Support

For any issues not covered in the troubleshooting section, or for parts replacement and professional servicing, please contact an authorized DOVAMAN service center. Always ensure genuine replacement parts are used to maintain the machine's performance and safety.

A user manual in PDF format is available for download. This document contains comprehensive information regarding the product. View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.