Introduction
Thank you for choosing the ANDELI OPTIM Series Welding Helmet Replacement Lens Kit. This kit provides essential outer and inner protective lenses designed to maintain the safety and clarity of your ANDELI OPTIM series auto-darkening welding helmet. This manual provides important safety information, installation instructions, maintenance guidelines, and troubleshooting tips to ensure proper use and longevity of your replacement lenses.
Safety Information
WARNING: Always read and understand all safety precautions before installing or using these replacement lenses in your welding helmet. Your safety depends on proper installation and maintenance of these protective components.
General Welding Safety
- ARC RAYS CAN BURN: Welding arc rays can injure eyes and burn skin. Always use a welding helmet with properly fitted and undamaged filter and cover plates. Wear appropriate protective clothing.
- ELECTRIC SHOCK CAN KILL: Ensure all welding equipment is properly grounded. Do not touch electrically 'hot' parts with bare skin or wet clothing.
- FUMES AND GASES CAN BE DANGEROUS: Welding produces fumes and gases hazardous to health. Avoid breathing these fumes. Use adequate ventilation or exhaust at the arc.
- WELDING AND CUTTING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area. Have a fire extinguisher readily available.
- PROTECTIVE EQUIPMENT: Always inspect your welding helmet, including all lenses, for damage before each use. Replace any damaged components immediately. Ensure clear lenses are clean and securely attached. Always wear safety glasses or goggles under the welding helmet.
Specifications
These replacement lenses are designed for compatibility with ANDELI OPTIM series auto-darkening welding helmets, including models such as RL-600LA and RL-600LB. They are manufactured from durable plastic (PP) to provide essential protection.
| Feature | Description |
|---|---|
| Material | Plastic (PP) |
| Type | Outer Protective Lens, Inner Protective Lens |
| Compatibility | ANDELI OPTIM Series Welding Helmets (e.g., RL-600LA, RL-600LB) |
| Function | Protects auto-darkening filter from spatter, scratches, and impact |

Figure 1: Gold outer protective lens and inner protective film, shown with compatible ANDELI OPTIM series welding helmets.

Figure 2: Clear outer protective lens and inner protective film, shown with compatible ANDELI OPTIM series welding helmets.
Installation (Setup)
WARNING: Never use the auto-darkening lens without the inside and outside lens covers properly installed. Welding spatter will damage the auto-darkening lens and void the warranty.
Important: Ensure you have removed the protective film from both sides of the new lenses before installation for clear vision.
Replacing the Outer Cover Lens
- Removal: Press down on one side of the buckle with your hand to release and remove the old outer cover lens.
- Installation: To install a new outer cover lens, first align and clip it into the middle groove. Then, press firmly on both sides until it locks securely into place.
Replacing the Inner Cover Lens
- Preparation: Remove the lens cover holder and take out the auto-darkening lens assembly from the helmet.
- Removal: To remove the inner lens cover, gently pry it upward using the thumbnail openings located on both sides. Slide the cover out from either side of the frame.
- Installation: Insert the new inner lens cover into the frame and reassemble the unit by reversing the above steps. Ensure it is seated correctly.

Figure 3: Inner protective films with warning to remove before use.
Maintenance
Cleaning the Lenses
- Regularly clean both outer and inner protective lenses.
- Use a soft, clean cloth to gently wipe the lens surfaces. Avoid abrasive materials or harsh chemicals that could scratch or damage the lenses.
- If lenses are heavily soiled or damaged, replace them immediately.
Storage
- Store replacement lenses in a clean, dry place away from direct sunlight, extreme temperatures, and corrosive substances.
- Keep lenses in their original packaging or a protective container to prevent scratches.
Inspection
- Before each use, inspect the installed lenses for any signs of damage, such as deep scratches, cracks, or excessive spatter buildup.
- Replace lenses if visibility is impaired or if they show any signs of damage that could compromise protection.
Troubleshooting (Lens-Related)
This section addresses common issues related to the protective lenses.
| Fault Description | Possible Cause | Solution |
|---|---|---|
| Irregular darkening or uneven dimming (of auto-darkening filter) | Dirty or damaged outer protective lens. | Clean outer lens with a soft cloth; replace if damaged. |
| Poor visibility through lens | Dirty outer/inner cover lenses or filter. | Replace soiled or scratched lenses. |
WARNING: If troubleshooting steps do not resolve the issue, discontinue use immediately and contact ANDELI support for assistance. Do not use a malfunctioning welding helmet or damaged lenses.
Replacement Parts
The following are the relevant replacement lens parts for ANDELI OPTIM series welding helmets:
- Outer Cover Lens: Part No. ADL-RL-010002
- Inner Cover Lens: Part No. ADL-RL-010004

Figure 4: Example of a replacement kit (gold outer lenses).

Figure 5: Example of a replacement kit (clear outer lenses).
User Tips
- Verify Compatibility: Always verify the compatibility of replacement lenses with your specific welding helmet model (e.g., ANDELI OPTIM series) before purchase to ensure a proper fit and optimal protection.
- Remove Protective Films: Ensure all protective films are removed from both sides of new lenses before installation for clear vision and proper function.
- Regular Replacement: Replace outer lenses frequently as they are exposed to spatter and scratches. Inner lenses should also be replaced if they become scratched or dirty.
Warranty & Support
For any questions, technical assistance, or warranty claims regarding your ANDELI products, please contact our After-Sales Center:
- USA: LIPOINCD-100, 12 Hughes Irvine, CA 92618
- Hong Kong: Workshop60, 3/F, Block A, East Sun, Industrial Centre, No.16 Shing Yip Street, Kwun Tong, Hong Kong
- Telephone: +19496179002 (USA); +85284807265 (HK)
- Email: support@andeligroup.com
- Website: www.andelitools.com