RIKA RK500-16

Contents

RIKA RK500-16 Nitrate Ion Sensor

Model: RK500-16 | Brand: RIKA

1. Introduction

The RIKA RK500-16 Nitrate ion (NO3-) sensor is designed to accurately determine the mass of nitrate ions (NO3-) in water. Elevated nitrate ion levels can result from decaying organic matter or industrial waste. This sensor is widely utilized across various sectors including industry, environmental protection, education, and Internet of Things applications. It supports both immersion in water and pipe installation, providing simultaneous NO3- and temperature measurements.

Key Features:

  • High performance sensitive film
  • Automatic temperature compensation
  • Durable PVC and POM housing
  • Simple operation and high reliability
  • Integrated design with no external modules required
  • Simultaneous NO3- and temperature measurement
  • Suitable for immersion in water or pipe installation

2. Technical Specifications

ItemTechnical Specification
NO3- (concentration) (2.5-11PH)Temperature
Range0.1-14000ppm0-50℃
Accuracy±1%FS±0.3℃
Resolution0.001ppm0.1℃
Supply5VDC, 12VDC, 24VDC
Temperature compensation0-60℃
OutputRS485 and 4-20mA at the same time
Pressure resistance0-3bar
Power consumption<0.4W
Operating temperature0-+80℃
Probe materialPC+316L
Weight (probe)0.5kg
Ingress protectionIP68
Cable length5m default, other length optional
Storage10-60℃ / 20%-90%RH

3. Setup and Installation

The RK500-16 sensor is designed for flexible installation, supporting both direct immersion and pipe integration. Proper installation is crucial for accurate and reliable measurements.

3.1. Components Overview

  • RK500-16 Sensor Probe
  • Integrated Cable (5m default, other lengths optional) with exposed wiring for connection.
RIKA RK500-16 Nitrate Ion Sensor with exposed wiring

Image: RIKA RK500-16 Nitrate Ion Sensor, showing the cable with exposed wires for connection.

3.2. Power and Data Connection

The sensor requires a DC power supply and provides data output via RS485 and 4-20mA simultaneously. Ensure correct wiring to your control system or data logger.

  • Power Supply: Connect to a 5VDC, 12VDC, or 24VDC source as required by your system.
  • Data Output: Integrate the RS485 and/or 4-20mA outputs with your monitoring equipment. Refer to your equipment's manual for specific wiring diagrams.

3.3. Physical Installation

The sensor can be installed in two primary ways:

  • Immersion: For direct measurement in tanks, ponds, or open water bodies. Ensure the probe tip is fully submerged in the liquid to be measured.
  • Pipe Installation: For inline monitoring in pipelines. Use appropriate fittings to secure the sensor within the pipe, ensuring no leaks and proper flow past the probe tip.
RIKA RK500-16 Nitrate Ion Sensor probe tip

Image: Close-up view of the RIKA RK500-16 Nitrate Ion Sensor probe tip.

Ensure the sensor is installed in a location that provides a representative sample of the water being monitored and is easily accessible for maintenance.

4. Operation

Once installed and powered, the RK500-16 sensor continuously measures nitrate ion concentration and temperature. The sensor's integrated design and automatic temperature compensation ensure accurate readings across varying environmental conditions.

4.1. Initial Power-Up

After connecting the power supply, allow a few minutes for the sensor to stabilize before taking readings. The sensor will begin transmitting data via its RS485 and 4-20mA outputs.

4.2. Data Acquisition

Connect the sensor's output to a compatible data logger, PLC, or display unit. Configure your receiving device to interpret the RS485 (Modbus protocol) or 4-20mA signals according to the sensor's specifications for nitrate ion concentration (ppm) and temperature (℃).

4.3. Continuous Monitoring

The RK500-16 is designed for continuous monitoring. Regularly check the data output for trends or anomalies that may indicate changes in water quality or sensor performance.

5. Maintenance

Regular maintenance ensures the longevity and accuracy of your RK500-16 sensor.

5.1. Cleaning the Probe

Over time, the sensor's sensitive film and probe tip may accumulate fouling from the water, affecting accuracy. Clean the probe regularly:

  • Gently remove the sensor from its installation point.
  • Rinse the probe tip with clean, distilled water.
  • If stubborn deposits are present, carefully wipe the probe tip with a soft cloth or brush. Avoid abrasive materials that could damage the sensitive film.
  • Do not use strong solvents or harsh chemicals unless specifically recommended by the manufacturer for particular types of fouling.
  • Reinstall the sensor after cleaning.
RIKA RK500-16 Nitrate Ion Sensor probe end

Image: RIKA RK500-16 Nitrate Ion Sensor, showing the probe end for cleaning.

5.2. Calibration

While the sensor is designed for high reliability, periodic calibration may be necessary to maintain optimal accuracy, especially in demanding applications or after prolonged use. Refer to your specific control system or data logger's instructions for calibration procedures, typically involving standard solutions of known nitrate ion concentrations.

5.3. Storage

When not in use, store the sensor in a dry environment between 10-60℃ with 20%-90%RH. Ensure the probe tip is protected from physical damage.

6. Troubleshooting

This section addresses common issues you might encounter with the RK500-16 sensor.

6.1. Inaccurate Readings

  • Fouling: The most common cause. Clean the sensor probe as described in Section 5.1.
  • Calibration: Sensor may require recalibration. Perform calibration using standard solutions.
  • Interference: Ensure the sensor is not exposed to strong electromagnetic fields or other sources of interference.
  • Environmental Conditions: Verify that the operating temperature and pressure are within the specified ranges.

6.2. No Output or Erratic Data

  • Power Supply: Check if the sensor is receiving the correct voltage (5VDC, 12VDC, or 24VDC).
  • Wiring: Inspect all cable connections for looseness, corrosion, or damage. Ensure correct polarity and signal connections.
  • Communication Settings: For RS485, verify that the baud rate, data bits, parity, and stop bits match your receiving device.
  • Sensor Damage: If physical damage is visible or suspected, the sensor may need replacement.

6.3. Alarm Activation

If the sensor is integrated with a control unit that triggers alarms, ensure the alarm thresholds are set correctly for your application. A testimonial indicates that the sensor works well with alarm systems when set to the correct threshold.

7. User Tips

  • Handle with Care: The sensor features a high-performance sensitive film. Avoid harsh physical contact or abrasive cleaning methods to prevent damage.
  • Leverage Automatic Temperature Compensation: The sensor's automatic temperature compensation feature ensures accurate readings across a wide temperature range (0-60℃). No manual adjustment for temperature variations is typically needed for the nitrate measurement itself.
  • Regular Cleaning is Key: To maintain measurement accuracy, especially in environments with high particulate matter or biological growth, establish a routine cleaning schedule for the probe.
  • Verify System Integration: When connecting to a larger monitoring system, double-check all wiring and communication protocols (RS485, 4-20mA) to ensure seamless data flow.

8. Warranty and Support

The RIKA RK500-16 Nitrate Ion Sensor comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Additionally, the manufacturer offers a 12-month quality guarantee and free exchange within one month for qualifying issues.

For technical support, troubleshooting assistance, or warranty claims, please contact your supplier or the manufacturer directly. Provide your product model (RK500-16) and purchase details when seeking support.

9. Application Industries

The RK500-16 Nitrate Ion Sensor is suitable for a wide range of applications requiring nitrate ion and temperature monitoring:

  • Industrial wastewater treatment
  • Sewage treatment
  • Aquaculture
  • Clean in place (CIP) systems
  • Environmental Engineering
  • General Water quality monitoring
Various application industries for the RIKA RK500-16 sensor

Image: Visual representation of the RK500-16 sensor's application in industrial wastewater, sewage, aquaculture, CIP, environmental engineering, and water quality monitoring.

10. Certifications

The RIKA RK500-16 sensor and its manufacturing processes adhere to international quality and environmental standards. Certifications include:

  • ISO9001 Quality Management System
  • CE Certification
  • RoHS Compliance
  • TÜV Certification
  • Calibration Certificate
  • WMO (World Meteorological Organization) related standards
Certifications for RIKA products including ISO9001, CE, RoHS, TUV

Image: Display of various certifications including ISO9001, CE, RoHS, and TUV, indicating product quality and compliance.

11. Frequently Asked Questions (FAQ)

Q: Are you the final manufacturer?
A: Yes, we are a SENSOR manufacturer and exporter in China with 10+ years experience and with the factory authorized by SGS.
Q: Do you offer OEM service?
A: Yes, we can offer OEM service and design the logo marking for you. The minimum quantity is 10pcs for the first order.
Q: Do you offer free samples?
A: Sorry, we do not offer free samples. You should pay for the samples and freight cost.
Q: What payment ways do you accept?
A: You can pay us by T/T, PayPal, and West Union.
Q: What is your delivery time?
A: It is 6-8 working days since the payment confirmed. If quantity is more than 100pcs/order, it will need an extra 3-5 working days.
Q: What is your normal delivery way?
A: Goods will be sent by DHL / FEDEX / UPS / EMS / TNT / or other proposed forwarders.
Q: How is your quality assurance service?
A: Our service is free exchange within one month and 12 months quality guarantee.
Q: Could we make a visit to your factory?
A: Yes, you are welcomed. But before that, we will do the visiting investigation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.