Jonsbo CA Series

Contents

JONSBO CA Series CPU Cooler User Manual

Models: CA40, CA80, CA90

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JONSBO CA Series CPU Cooler. The CA Series includes models CA40, CA80, and CA90, designed to provide efficient cooling for a wide range of Intel and AMD processors. Please read this manual thoroughly before installation to ensure proper setup and optimal performance.

JONSBO CA Series CPU Coolers (CA40, CA80, CA90) with ARGB fans and integrated top cover.

Figure 1: JONSBO CA Series CPU Coolers (CA40, CA80, CA90)

2. Product Overview

2.1 Features

  • Integrated Hot Stamping Top Cover: Sleek design with metallic texture and diagonal pull hot stamping grille.
  • ARGB Lighting Effects: Esports aesthetic ARGB lighting effects with motherboard synchronization (ASUS AURA, GIGABYTE RGB FUSION, MSI MYSTIC LIGHT SYNC, ASRock POLYCHROME SYNC).
  • High Performance Composite Heat Pipes: Features 6mm heat pipes (4 for CA40, 6 for CA80/CA90) with anti-gravity design and nickel plating for anti-oxidation.
  • Efficient Heat Dissipation: Newly tuned and optimized heat pipes and fans for excellent thermal performance.
  • Memory Compatibility: Twisted neck heat pipe design to avoid interference with RAM modules, ensuring good compatibility with various memory heights.
  • Easy Installation: Designed for straightforward installation across multiple platforms.
  • Quiet Operation: Fan speeds optimized for a balance of cooling and low noise levels.
ARGB lighting effects synchronization with motherboard software.

Figure 2: ARGB Lighting Synchronization

Diagram showing high performance composite heat pipes with anti-gravity design.

Figure 3: High Performance Heat Pipe Design

Diagram illustrating memory compatibility with twisted neck heat pipe design.

Figure 4: Memory Compatibility Design

2.2 Component List

Please verify that all components are present in your package:

Image showing metal buckle strip, various spacer columns for different platforms (LGA115X/1200, LGA1700/1851, AM4/AM5), mounting hardware, and thermal paste.

Figure 5: Mounting Hardware and Accessories

  1. CPU Heatsink Assembly
  2. Intel Backplate
  3. Intel Mounting Brackets
  4. AMD Mounting Brackets
  5. Intel Spacer Columns (LGA115X/1200, LGA1700/1851)
  6. AMD Spacer Columns
  7. Mounting Screws (Intel & AMD)
  8. Thermal Paste
  9. Fan(s) (pre-installed or separate depending on model)

3. Specifications

Attribute CA40 CA80 CA90
Cooler Type Tower
Heat Sink Size (L*W*H) 120mm * 73mm * 157mm 120mm * 135mm * 159mm 130mm * 135mm * 159mm
Heat Pipe Size Ø6mm * 4pcs Ø6mm * 6pcs Ø6mm * 6pcs
D-TDP 225W 260W 270W
Fan Size 120mm * 120mm * 25mm Fan 1: 120mm * 120mm * 25mm
Fan 2: 120mm * 120mm * 25mm
Fan 1: 130mm * 130mm * 25mm
Fan 2: 120mm * 120mm * 25mm
Fan Speed 800-1800 RPM ± 10% Fan 1: 800-1800 RPM ± 10%
Fan 2: 600-1500 RPM ± 10%
Fan 1: 800-1800 RPM ± 10%
Fan 2: 800-1800 RPM ± 10%
Air Volume 29.26-69.61 CFM Fan 1: 29.26-69.61 CFM
Fan 2: 28.05-56.53 CFM
Fan 1: 24.26-76.57 CFM
Fan 2: 29.26-69.61 CFM
Air Pressure 0.35-1.79 mmH2O Fan 1: 0.35-1.79 mmH2O
Fan 2: 0.47-1.32 mmH2O
Fan 1: 0.30-1.98 mmH2O
Fan 2: 0.35-1.79 mmH2O
Noise 17.0-32.6 dB(A) (MAX) Fan 1: 17.0-32.6 dB(A) (MAX)
Fan 2: 15.6-30.2 dB(A) (MAX)
Fan 1: 18.2-31.4 dB(A) (MAX)
Fan 2: 17.0-32.6 dB(A) (MAX)
Fan Life 50,000 hrs (220,000 hours at 25℃ room temp)
Bearing Fluid Bearing
Power Interface PWM 4PIN, 5v-3pin ARGB Fan 1: PWM 4PIN, 5v-3pin ARGB
Fan 2: PWM 4PIN
Fan 1: PWM 4PIN
Fan 2: PWM 4PIN, 5v-3pin ARGB
Supported CPU Sockets Intel: LGA 1150, LGA 1151, LGA 1155, LGA 1156, LGA1200, LGA 1700, LGA 1851
AMD: Socket AM4, Socket AM5
Certification CE, RoHS
CA40 Specifications diagram showing dimensions, fan details, and noise levels.

Figure 6: CA40 Radiator and Fan Specifications

CA80 Specifications diagram showing dimensions, fan details, and noise levels.

Figure 7: CA80 Radiator and Fan Specifications

CA90 Specifications diagram showing dimensions, fan details, and noise levels.

Figure 8: CA90 Radiator and Fan Specifications

4. Setup and Installation

Before starting, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific details on CPU cooler installation if needed.

4.1 Intel Platform Installation (LGA1200/115X/1700/1851)

Intel LGA1200/115X/1700/1851 installation steps diagram.

Figure 9: Intel Installation Overview

  1. Prepare Backplate: Install the Intel backplate to the motherboard from the rear. Secure it with the appropriate Intel spacer columns (11.8mm for LGA115X/1200, 10.8mm for LGA1700/1851).
  2. Install Mounting Brackets: Attach the Intel mounting brackets to the front side of the motherboard, over the spacer columns, and secure them with the provided screws.
  3. Apply Thermal Paste: Apply a small amount of thermal paste to the center of your CPU's IHS (Integrated Heat Spreader). Ensure to remove any protective film from the radiator base before proceeding.
  4. Mount Heatsink: Carefully place the heatsink assembly onto the CPU, aligning the screws on the heatsink base with the mounting points on the brackets. Tighten the screws in a cross pattern until snug, but do not overtighten.
  5. Connect Fan and ARGB: Connect the CPU fan's 4-pin PWM cable to the CPU_FAN header on your motherboard. If your cooler has ARGB lighting, connect the 5V-3pin ARGB cable to an available ARGB header on your motherboard.

4.2 AMD Platform Installation (AM4/AM5)

AMD AM4/AM5 installation steps diagram.

Figure 10: AMD Installation Overview

  1. Prepare Motherboard: Remove the plastic retention module from the stock AMD backplate on your motherboard. The existing AMD backplate will be reused.
  2. Install Spacer Columns: Place the AMD spacer columns (10mm) onto the four screw holes around the CPU socket.
  3. Install Mounting Brackets: Attach the AMD mounting brackets to the front side of the motherboard, over the spacer columns, and secure them with the provided screws.
  4. Apply Thermal Paste: Apply a small amount of thermal paste to the center of your CPU's IHS. Ensure to remove any protective film from the radiator base before proceeding.
  5. Mount Heatsink: Carefully place the heatsink assembly onto the CPU, aligning the screws on the heatsink base with the mounting points on the brackets. Tighten the screws in a cross pattern until snug, but do not overtighten.
  6. Connect Fan and ARGB: Connect the CPU fan's 4-pin PWM cable to the CPU_FAN header on your motherboard. If your cooler has ARGB lighting, connect the 5V-3pin ARGB cable to an available ARGB header on your motherboard.

5. Operating Instructions

Once the cooler is installed and all cables are connected, you can power on your system. The fan speed will be automatically controlled by your motherboard's PWM settings based on CPU temperature. For ARGB lighting, you can control effects through your motherboard's RGB software (e.g., ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, ASRock Polychrome Sync).

Ensure your motherboard's BIOS/UEFI settings are configured to use PWM fan control for the CPU fan header to allow for dynamic fan speed adjustments.

6. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your CPU cooler.

  • Dust Cleaning: Periodically clean dust from the heatsink fins and fan blades using compressed air or a soft brush. Ensure the system is powered off before cleaning.
  • Thermal Paste: Thermal paste typically lasts for several years. If you notice a significant increase in CPU temperatures, consider reapplying fresh thermal paste. This involves carefully removing the heatsink, cleaning off old paste from both the CPU and heatsink base, and applying new paste.
  • Fan Inspection: Check fan blades for any obstructions or damage. Ensure the fan spins freely and quietly.

7. Troubleshooting

  • Fan Not Spinning:
    • Check if the 4-pin PWM fan cable is securely connected to the CPU_FAN header on the motherboard.
    • Verify fan settings in your motherboard's BIOS/UEFI.
  • Poor Cooling Performance (High CPU Temps):
    • Ensure the heatsink is properly seated on the CPU and mounting screws are tightened evenly.
    • Check if thermal paste was applied correctly and evenly. Reapply if necessary.
    • Clean any dust accumulation from the heatsink fins and fan blades.
    • Verify that the fan is spinning at an appropriate speed.
  • ARGB Lights Not Working:
    • Ensure the 5V-3pin ARGB cable is correctly connected to a compatible ARGB header on your motherboard.
    • Check your motherboard's RGB software for lighting control.
    • Verify that the ARGB header is enabled in your motherboard's BIOS/UEFI.
  • Excessive Noise:
    • Check for any cables or obstructions hitting the fan blades.
    • Ensure the fan is securely mounted and not vibrating.
    • Dust accumulation can sometimes cause noise; clean the fan.

8. User Tips

  • Cable Management: Route fan and ARGB cables neatly to avoid interference with other components and to improve airflow within your PC case.
  • BIOS/UEFI Settings: Explore your motherboard's BIOS/UEFI settings for fan curves to customize cooling performance and noise levels to your preference.
  • Thermal Paste Application: A pea-sized dot in the center of the CPU is generally sufficient for most thermal pastes, allowing the pressure from the heatsink to spread it evenly.

9. Warranty and Support

JONSBO CA Series CPU Coolers come with a 3-year product warranty. For warranty claims or technical support, please contact your retailer or the manufacturer directly.

For additional information and detailed diagrams, you may refer to the official user manual PDF: JONSBO CA Series User Manual (PDF).

Manufacturer: Dongguan Sibositong Industrial Co., Ltd.

Address: No.5, Xinglong Lu, Sanzhong Village, Qingxi Town, Dongguan City, Guangdong Province, 523651, China

© 2024 JONSBO. All rights reserved. Specifications are subject to change without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.